Re: [PATCH 23/37] pinctrl: renesas: rzg2l: index all registers based on port offset

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Claudiu,

Thanks for your patch!

On Tue, Sep 12, 2023 at 6:53 AM Claudiu <claudiu.beznea@xxxxxxxxx> wrote:
> From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
>
> To get address that needs to be read/write for specific port
> functionalities the P(), PM(), PMC(), PFC(), PIN(), IOLH() IEN(), ISEL()
> macros are used. Some of these macros received as argument the hardware
> port identifier, some hardware port offset address (e.g. ISEL() received
> port identifier, IOLH() received port offset address). This makes hard to
> extend the current driver for SoCs were port identifiers are not continuous
> in memory map of pin controller. This is the case for RZ/G3S pin controller
> were ports are mapped as follows:
>
> port offset    port identifier
> -----------    ---------------
> 0x20           P0
> 0x21           P5
> 0x22           P6
> 0x23           P11
> 0x24           P12
> 0x25           P13
> 0x26           P14
> 0x27           P15
> 0x28           P16
> 0x29           P17
> 0x2a           P18
> 0x30           P1
> 0x31           P2
> 0x32           P3
> 0x33           P4
> 0x34           P7
> 0x35           P8
> 0x36           P8
> 0x37           P10
>
> To make this achievable change all the above macros used to get the address
> of a port register for specific port functionality based on port hardware
> address. Shortly, all the above macros will get as argument the port
> offset address listed in the above table.
>
> With this RZG2L_SINGLE_PIN_GET_PORT_OFFSET() and
> RZG2L_PIN_ID_TO_PORT_OFFSET() were replaced by

and RZG2L_GPIO_PORT_GET_INDEX()?

> RZG2L_PIN_CFG_TO_PORT_OFFSET(), RZG2L_SINGLE_PIN_GET_CFGS() and
> RZG2L_GPIO_PORT_GET_CFGS() were replaced by RZG2L_PIN_CFG_TO_CAPS().
>
> Also rzg2l_pinctrl_set_pfc_mode() don't need port argument anymore.
> Also rzg2l_gpio_direction_input() and rzg2l_gpio_direction_output() don't
> need to translate port and bit locally as this can be done by
> rzg2l_gpio_set_direction().
>
> To use the same naming for port, bit/pin and register offset the
> port_offset variable names in different places was replaced by variable
> named off and there is no need to initialize anymore cfg and bit in
> different code places.
>
> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>

This looks like a nice cleanup, thanks a lot!
Prabhakar: do you like it, too?

Reviewed-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
You can find a few suggestions for improvement below...

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -202,9 +202,11 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
>                                  unsigned int group_selector)
>  {
>         struct rzg2l_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> +       const struct pinctrl_pin_desc *pin_desc;
> +       unsigned int i, *psel_val, *pin_data;
>         struct function_desc *func;
> -       unsigned int i, *psel_val;
>         struct group_desc *group;
> +       u32 port, pin, off;

Please move the new variable declarations inside the for(), and
combine them with their initialization.

>         int *pins;
>
>         func = pinmux_generic_get_function(pctldev, func_selector);
> @@ -218,11 +220,17 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
>         pins = group->pins;
>
>         for (i = 0; i < group->num_pins; i++) {
> -               dev_dbg(pctrl->dev, "port:%u pin: %u PSEL:%u\n",
> -                       RZG2L_PIN_ID_TO_PORT(pins[i]), RZG2L_PIN_ID_TO_PIN(pins[i]),
> -                       psel_val[i]);
> -               rzg2l_pinctrl_set_pfc_mode(pctrl, RZG2L_PIN_ID_TO_PORT(pins[i]),
> -                                          RZG2L_PIN_ID_TO_PIN(pins[i]), psel_val[i]);
> +               pin_desc = &pctrl->desc.pins[pins[i]];
> +               pin_data = pin_desc->drv_data;
> +
> +               port = RZG2L_PIN_ID_TO_PORT(pins[i]);

As port is unused but in the debug print, please drop the variable,
and use RZG2L_PIN_ID_TO_PORT() in the debug print below.

> +               pin = RZG2L_PIN_ID_TO_PIN(pins[i]);
> +               off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
> +
> +               dev_dbg(pctrl->dev, "port:%u pin: %u off:%x PSEL:%u\n", port,
> +                       pin, off, psel_val[i]);
> +
> +               rzg2l_pinctrl_set_pfc_mode(pctrl, pin, off, psel_val[i]);
>         }

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux