From: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>
Add the support of SDIO in-band interrupt mode for STM32 and Ux500
variants.
It allows the SD I/O card to interrupt the host on SDMMC_D1 data line.
It is not enabled by default on Ux500 variant as this is unstable and
Ux500 users should use out-of-band IRQs.
Signed-off-by: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>
Signed-off-by: Yann Gautier <yann.gautier@xxxxxxxxxxx>
---
Updates on v2:
* rename use_sdio_irq to supports_sdio_irq and change it to bool
* use common code for ux500 and stm32 variants
---
drivers/mmc/host/mmci.c | 85 +++++++++++++++++++++++++++++
drivers/mmc/host/mmci.h | 7 +++
drivers/mmc/host/mmci_stm32_sdmmc.c | 2 +
3 files changed, 94 insertions(+)
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index dda756a563793..65cc03ee7f23b 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -272,6 +272,7 @@ static struct variant_data variant_stm32_sdmmc = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(12, 5),
.stm32_idmabsize_align = BIT(5),
+ .supports_sdio_irq = true,
.busy_timeout = true,
.busy_detect = true,
.busy_detect_flag = MCI_STM32_BUSYD0,
@@ -299,6 +300,7 @@ static struct variant_data variant_stm32_sdmmcv2 = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(16, 5),
.stm32_idmabsize_align = BIT(5),
+ .supports_sdio_irq = true,
.dma_lli = true,
.busy_timeout = true,
.busy_detect = true,
@@ -327,6 +329,7 @@ static struct variant_data variant_stm32_sdmmcv3 = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(16, 6),
.stm32_idmabsize_align = BIT(6),
+ .supports_sdio_irq = true,
.dma_lli = true,
.busy_timeout = true,
.busy_detect = true,
@@ -423,6 +426,11 @@ static void mmci_write_datactrlreg(struct mmci_host *host, u32 datactrl)
/* Keep busy mode in DPSM if enabled */
datactrl |= host->datactrl_reg & host->variant->busy_dpsm_flag;
+ /* Keep SD I/O interrupt mode enabled */
+ if (host->variant->supports_sdio_irq &&
+ host->mmc->caps & MMC_CAP_SDIO_IRQ)
+ datactrl |= host->variant->datactrl_mask_sdio;
+
if (host->datactrl_reg != datactrl) {
host->datactrl_reg = datactrl;
writel(datactrl, host->base + MMCIDATACTRL);
@@ -817,6 +825,25 @@ static bool ux500_busy_complete(struct mmci_host *host, struct mmc_command *cmd,
return (host->busy_state == MMCI_BUSY_DONE);
}
+void ux500_and_stm32_enable_sdio_irq(struct mmci_host *host, int enable)
+{
+ void __iomem *base = host->base;
+ u32 mask = readl_relaxed(base + MMCIMASK0);
+
+ if (enable)
+ writel_relaxed(mask | MCI_ST_SDIOITMASK, base + MMCIMASK0);
+ else
+ writel_relaxed(mask & ~MCI_ST_SDIOITMASK, base + MMCIMASK0);
+}
+
+void ux500_and_stm32_sdio_irq(struct mmci_host *host, u32 status)
+{
+ if (status & MCI_ST_SDIOIT) {
+ ux500_and_stm32_enable_sdio_irq(host, 0);
+ sdio_signal_irq(host->mmc);
+ }
+}
+
/*
* All the DMA operation mode stuff goes inside this ifdef.
* This assumes that you have a generic DMA device interface,
@@ -1191,6 +1218,8 @@ static void ux500_variant_init(struct mmci_host *host)
{
host->ops = &mmci_variant_ops;
host->ops->busy_complete = ux500_busy_complete;
+ host->ops->enable_sdio_irq = ux500_and_stm32_enable_sdio_irq;
+ host->ops->sdio_irq = ux500_and_stm32_sdio_irq;
}
static void ux500v2_variant_init(struct mmci_host *host)
@@ -1198,6 +1227,8 @@ static void ux500v2_variant_init(struct mmci_host *host)
host->ops = &mmci_variant_ops;
host->ops->busy_complete = ux500_busy_complete;
host->ops->get_datactrl_cfg = ux500v2_get_dctrl_cfg;
+ host->ops->enable_sdio_irq = ux500_and_stm32_enable_sdio_irq;
+ host->ops->sdio_irq = ux500_and_stm32_sdio_irq;
}
static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
@@ -1805,6 +1836,11 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
mmci_data_irq(host, host->data, status);
}
+ if (host->variant->supports_sdio_irq &&
+ host->mmc->caps & MMC_CAP_SDIO_IRQ &&
+ host->ops && host->ops->sdio_irq)
+ host->ops->sdio_irq(host, status);
+
/*
* Busy detection has been handled by mmci_cmd_irq() above.
* Clear the status bit to prevent polling in IRQ context.
@@ -2041,6 +2077,45 @@ static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
return ret;
}
+static void mmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+ struct mmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ if (!host->variant->supports_sdio_irq)
+ return;
+
+ if (host->ops && host->ops->enable_sdio_irq) {
+ if (enable)
+ /* Keep device active while SDIO IRQ is enabled */
+ pm_runtime_get_sync(mmc_dev(mmc));
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->ops->enable_sdio_irq(host, enable);
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ if (!enable) {
+ pm_runtime_mark_last_busy(mmc_dev(mmc));
+ pm_runtime_put_autosuspend(mmc_dev(mmc));
+ }
+ }
+}
+
+static void mmci_ack_sdio_irq(struct mmc_host *mmc)
+{
+ struct mmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ if (!host->variant->supports_sdio_irq)
+ return;
+
+ if (host->ops && host->ops->enable_sdio_irq) {
+ spin_lock_irqsave(&host->lock, flags);
+ host->ops->enable_sdio_irq(host, 1);
+ spin_unlock_irqrestore(&host->lock, flags);
+ }
+}
+
static struct mmc_host_ops mmci_ops = {
.request = mmci_request,
.pre_req = mmci_pre_request,
@@ -2049,6 +2124,8 @@ static struct mmc_host_ops mmci_ops = {
.get_ro = mmc_gpio_get_ro,
.get_cd = mmci_get_cd,
.start_signal_voltage_switch = mmci_sig_volt_switch,
+ .enable_sdio_irq = mmci_enable_sdio_irq,
+ .ack_sdio_irq = mmci_ack_sdio_irq,
};
static void mmci_probe_level_translator(struct mmc_host *mmc)
@@ -2316,6 +2393,14 @@ static int mmci_probe(struct amba_device *dev,
mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
}
+ if (variant->supports_sdio_irq && host->mmc->caps & MMC_CAP_SDIO_IRQ) {
+ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
+
+ if (variant->datactrl_mask_sdio)
+ mmci_write_datactrlreg(host,
+ host->variant->datactrl_mask_sdio);
+ }
+
/* Variants with mandatory busy timeout in HW needs R1B responses. */
if (variant->busy_timeout)
mmc->caps |= MMC_CAP_NEED_RSP_BUSY;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 253197f132fca..5ea4975c18ec5 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -331,6 +331,7 @@ enum mmci_busy_state {
* register.
* @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
* @dma_lli: true if variant has dma link list feature.
+ * @supports_sdio_irq: allow SD I/O card to interrupt the host
* @stm32_idmabsize_mask: stm32 sdmmc idma buffer size.
*/
struct variant_data {
@@ -376,6 +377,7 @@ struct variant_data {
u32 start_err;
u32 opendrain;
u8 dma_lli:1;
+ bool supports_sdio_irq;
u32 stm32_idmabsize_mask;
u32 stm32_idmabsize_align;
void (*init)(struct mmci_host *host);
@@ -400,6 +402,8 @@ struct mmci_host_ops {
bool (*busy_complete)(struct mmci_host *host, struct mmc_command *cmd, u32 status, u32 err_msk);
void (*pre_sig_volt_switch)(struct mmci_host *host);
int (*post_sig_volt_switch)(struct mmci_host *host, struct mmc_ios *ios);
+ void (*enable_sdio_irq)(struct mmci_host *host, int enable);
+ void (*sdio_irq)(struct mmci_host *host, u32 status);
};
struct mmci_host {
@@ -481,6 +485,9 @@ void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data);
void mmci_dmae_error(struct mmci_host *host);
#endif
+void ux500_and_stm32_enable_sdio_irq(struct mmci_host *host, int enable);
+void ux500_and_stm32_sdio_irq(struct mmci_host *host, u32 status);
+
#ifdef CONFIG_MMC_QCOM_DML
void qcom_variant_init(struct mmci_host *host);
#else
diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
index 35067e1e6cd80..fbfaa0bcec51e 100644
--- a/drivers/mmc/host/mmci_stm32_sdmmc.c
+++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
@@ -681,6 +681,8 @@ static struct mmci_host_ops sdmmc_variant_ops = {
.busy_complete = sdmmc_busy_complete,
.pre_sig_volt_switch = sdmmc_pre_sig_volt_vswitch,
.post_sig_volt_switch = sdmmc_post_sig_volt_switch,
+ .enable_sdio_irq = ux500_and_stm32_enable_sdio_irq,
+ .sdio_irq = ux500_and_stm32_sdio_irq,
};
static struct sdmmc_tuning_ops dlyb_tuning_mp15_ops = {
--
2.34.1
