On Fri, 21 Jul 2023 at 12:14, Victor Shih <victorshihgli@xxxxxxxxx> wrote:
>
> From: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
>
> Add UHS-II specific data structures for commands and defines for
> registers, as described in Part 1 UHS-II Addendum Version 1.01.
>
> UHS-II related definitions are listed below:
> 1. UHS-II card capability: sd_uhs2_caps{}
> 2. UHS-II configuration: sd_uhs2_config{}
> 3. UHS-II Command structure: uhs2_command{}
> 4. UHS-II register I/O address and register field definitions: sd_uhs2.h
>
I have a problem reviewing this, mainly because of one reason.
That is, that you are adding things that aren't really directly
related to the UHS-II Addendum, but rather used for how we should
implement the UHS-II support. I suggest we drop the other parts from
$subject patch and move them into the patch that actually needs them.
See comments below.
> Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> Signed-off-by: Jason Lai <jason.lai@xxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
> ---
>
> Updates in V7:
> - Remove unnecessary definitions.
>
> Updates in V6:
> - Remove unnecessary definitions and functions.
>
> ---
>
> include/linux/mmc/card.h | 31 ++++-
> include/linux/mmc/core.h | 13 ++
> include/linux/mmc/host.h | 39 +++++-
> include/linux/mmc/sd_uhs2.h | 240 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 319 insertions(+), 4 deletions(-)
> create mode 100644 include/linux/mmc/sd_uhs2.h
>
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 469fd68f854f..5cfc94b778f4 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -190,6 +190,12 @@ struct sd_switch_caps {
> #define SD_MAX_CURRENT_400 (1 << SD_SET_CURRENT_LIMIT_400)
> #define SD_MAX_CURRENT_600 (1 << SD_SET_CURRENT_LIMIT_600)
> #define SD_MAX_CURRENT_800 (1 << SD_SET_CURRENT_LIMIT_800)
> +
> +#define SD4_SET_POWER_LIMIT_0_72W 0
> +#define SD4_SET_POWER_LIMIT_1_44W 1
> +#define SD4_SET_POWER_LIMIT_2_16W 2
> +#define SD4_SET_POWER_LIMIT_2_88W 3
> +#define SD4_SET_POWER_LIMIT_1_80W 4
> };
>
> struct sd_ext_reg {
> @@ -213,7 +219,30 @@ struct sd_ext_reg {
>
> struct sd_uhs2_config {
> u32 node_id;
> - /* TODO: Extend with more register configs. */
> +
> + u32 n_fcu;
> + u32 maxblk_len;
> + u8 n_lanes;
> + u8 dadr_len;
> + u8 app_type;
> + u8 phy_minor_rev;
> + u8 phy_major_rev;
> + u8 can_hibernate;
> + u8 n_lss_sync;
> + u8 n_lss_dir;
> + u8 link_minor_rev;
> + u8 link_major_rev;
> + u8 dev_type;
> + u8 n_data_gap;
> +
> + u32 n_fcu_set;
> + u32 maxblk_len_set;
> + u8 n_lanes_set;
> + u8 speed_range_set;
> + u8 n_lss_sync_set;
> + u8 n_lss_dir_set;
> + u8 n_data_gap_set;
> + u8 max_retry_set;
> };
>
> struct sdio_cccr {
> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> index 6efec0b9820c..2a0581d87706 100644
> --- a/include/linux/mmc/core.h
> +++ b/include/linux/mmc/core.h
> @@ -23,6 +23,14 @@ enum mmc_blk_status {
> MMC_BLK_NEW_REQUEST,
> };
>
> +struct uhs2_command {
> + u16 header;
> + u16 arg;
> + __be32 *payload;
> + u32 payload_len;
> + u32 packet_len;
> +};
Let's move this to a later patch in the series.
> +
> struct mmc_command {
> u32 opcode;
> u32 arg;
> @@ -109,6 +117,11 @@ struct mmc_command {
> unsigned int busy_timeout; /* busy detect timeout in ms */
> struct mmc_data *data; /* data segment associated with cmd */
> struct mmc_request *mrq; /* associated request */
> +
> + struct uhs2_command *uhs2_cmd; /* UHS2 command */
> + u8 *uhs2_resp; /* UHS2 native cmd resp */
> + u8 uhs2_resp_len; /* UHS2 native cmd resp len */
> + u8 uhs2_tmode0_flag; /* UHS2 transfer mode flag */
Maybe I asked this before, but why can't the uhs2_tmode0_flag be moved
to the struct uhs2_command?
Moreover, let's move these changes to a later patch in the series.
> };
>
> struct mmc_data {
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 6f1be9993e16..8803fe46ed24 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -16,6 +16,7 @@
> #include <linux/mmc/pm.h>
> #include <linux/dma-direction.h>
> #include <linux/blk-crypto-profile.h>
> +#include <linux/mmc/sd_uhs2.h>
>
> struct mmc_ios {
> unsigned int clock; /* clock rate */
> @@ -99,7 +100,29 @@ struct mmc_clk_phase_map {
> };
>
> struct sd_uhs2_caps {
> - /* TODO: Add UHS-II capabilities for the host. */
> + u32 dap;
> + u32 gap;
> + u32 group_desc;
> + u32 maxblk_len;
> + u32 n_fcu;
> + u8 n_lanes;
> + u8 addr64;
> + u8 card_type;
> + u8 phy_rev;
> + u8 speed_range;
> + u8 n_lss_sync;
> + u8 n_lss_dir;
> + u8 link_rev;
> + u8 host_type;
> + u8 n_data_gap;
> +
> + u32 maxblk_len_set;
> + u32 n_fcu_set;
> + u8 n_lanes_set;
> + u8 n_lss_sync_set;
> + u8 n_lss_dir_set;
> + u8 n_data_gap_set;
> + u8 max_retry_set;
> };
>
> enum sd_uhs2_operation {
> @@ -345,6 +368,7 @@ struct mmc_pwrseq;
>
> struct mmc_supply {
> struct regulator *vmmc; /* Card power supply */
> + struct regulator *vmmc2; /* UHS2 VDD2 power supply */
We already added vqmmc2 (below) in a previous patch, to be used for
the VDD2 supply. This should not be needed, right?
In any case, let's drop it from the $subject patch - and if needed,
let's add it later on.
> struct regulator *vqmmc; /* Optional Vccq supply */
> struct regulator *vqmmc2; /* Optional supply for phy */
> };
> @@ -366,10 +390,12 @@ struct mmc_host {
> u32 ocr_avail_sdio; /* SDIO-specific OCR */
> u32 ocr_avail_sd; /* SD-specific OCR */
> u32 ocr_avail_mmc; /* MMC-specific OCR */
> + u32 ocr_avail_uhs2; /* UHS2-specific OCR */
I doubt that we need this, but if so, let's move this to a later patch
in the series.
> struct wakeup_source *ws; /* Enable consume of uevents */
> u32 max_current_330;
> u32 max_current_300;
> u32 max_current_180;
> + u32 max_current_180_vdd2; /* UHS2 vdd2 max curt. */
>
> #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
> #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
> @@ -465,12 +491,13 @@ struct mmc_host {
> #endif
> #define MMC_CAP2_ALT_GPT_TEGRA (1 << 28) /* Host with eMMC that has GPT entry at a non-standard location */
>
> - struct sd_uhs2_caps uhs2_caps; /* Host UHS-II capabilities */
> -
We just added this from a previous patch in the series - and now you
suggest moving it? Please update the original patch instead, if you
want it to be placed somewhere else.
> int flags;
> #define MMC_UHS2_SUPPORT (1 << 0)
> #define MMC_UHS2_SD_TRAN (1 << 1)
>
> + bool uhs2_app_cmd; /* Host UHS-II APP Command */
Let's move this to a later patch in the series.
> + struct sd_uhs2_caps uhs2_caps; /* Host UHS-II capabilities */
> +
> int fixed_drv_type; /* fixed driver type for non-removable media */
>
> mmc_pm_flag_t pm_caps; /* supported pm features */
> @@ -721,6 +748,12 @@ static inline void mmc_debugfs_err_stats_inc(struct mmc_host *host,
> host->err_stats[stat] += 1;
> }
>
> +static inline int mmc_card_uhs2_hd_mode(struct mmc_host *host)
> +{
> + return host->ios.timing == MMC_TIMING_UHS2_SPEED_A_HD ||
> + host->ios.timing == MMC_TIMING_UHS2_SPEED_B_HD;
> +}
Let's move this to a later patch in the series.
> +
> int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> new file mode 100644
> index 000000000000..7abe9bd870c7
> --- /dev/null
> +++ b/include/linux/mmc/sd_uhs2.h
> @@ -0,0 +1,240 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Header file for UHS-II packets, Host Controller registers and I/O
> + * accessors.
> + *
> + * Copyright (C) 2014 Intel Corp, All Rights Reserved.
> + */
> +#ifndef LINUX_MMC_UHS2_H
> +#define LINUX_MMC_UHS2_H
> +
> +/* LINK Layer definition */
> +/*
> + * UHS2 Header:
> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> + * bit [3:0] : DID(Destination ID = Node ID of UHS2 card)
> + * bit [6:4] : TYP(Packet Type)
> + * 000b: CCMD(Control command packet)
> + * 001b: DCMD(Data command packet)
> + * 010b: RES(Response packet)
> + * 011b: DATA(Data payload packet)
> + * 111b: MSG(Message packet)
> + * Others: Reserved
> + * bit [7] : NP(Native Packet)
> + * bit [10:8] : TID(Transaction ID)
> + * bit [11] : Reserved
> + * bit [15:12]: SID(Source ID 0: Node ID of Host)
> + *
> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> + */
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> + * bit [3:0] : MSB of IOADR
> + * bit [5:4] : PLEN(Payload Length)
> + * 00b: 0 byte
> + * 01b: 4 bytes
> + * 10b: 8 bytes
> + * 11b: 16 bytes
> + * bit [6] : Reserved
> + * bit [7] : R/W(Read/Write)
> + * 0: Control read command
> + * 1: Control write command
> + * bit [15:8] : LSB of IOADR
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_NATIVE_PACKET_POS 7
> +#define UHS2_NATIVE_PACKET (1 << UHS2_NATIVE_PACKET_POS)
> +
> +#define UHS2_PACKET_TYPE_POS 4
> +#define UHS2_PACKET_TYPE_CCMD (0 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DCMD (1 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DATA (3 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> +
> +#define UHS2_DEST_ID_MASK 0x0F
> +#define UHS2_DEST_ID 0x1
> +
> +#define UHS2_SRC_ID_POS 12
> +#define UHS2_SRC_ID_MASK 0xF000
> +
> +#define UHS2_TRANS_ID_POS 8
> +#define UHS2_TRANS_ID_MASK 0x0700
> +
> +/* UHS2 MSG */
> +#define UHS2_MSG_CTG_POS 5
> +#define UHS2_MSG_CTG_LMSG 0x00
> +#define UHS2_MSG_CTG_INT 0x60
> +#define UHS2_MSG_CTG_AMSG 0x80
> +
> +#define UHS2_MSG_CTG_FCREQ 0x00
> +#define UHS2_MSG_CTG_FCRDY 0x01
> +#define UHS2_MSG_CTG_STAT 0x02
> +
> +#define UHS2_MSG_CODE_POS 8
> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR 0x8
> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR 0x8
> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR 0x1
> +
> +/* TRANS Layer definition */
> +
> +/* Native packets*/
> +#define UHS2_NATIVE_CMD_RW_POS 7
> +#define UHS2_NATIVE_CMD_WRITE (1 << UHS2_NATIVE_CMD_RW_POS)
> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> +
> +#define UHS2_NATIVE_CMD_PLEN_POS 4
> +#define UHS2_NATIVE_CMD_PLEN_4B (1 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_8B (2 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_16B (3 << UHS2_NATIVE_CMD_PLEN_POS)
> +
> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK 0xF00
> +#define UHS2_NATIVE_CCMD_MIOADR_MASK 0x0F
> +
> +#define UHS2_NATIVE_CCMD_LIOADR_POS 8
> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK 0x0FF
> +
> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG BIT(11)
> +#define UHS2_DEV_INIT_PAYLOAD_LEN 1
> +#define UHS2_DEV_INIT_RESP_LEN 6
> +#define UHS2_DEV_ENUM_PAYLOAD_LEN 1
> +#define UHS2_DEV_ENUM_RESP_LEN 8
> +#define UHS2_CFG_WRITE_PAYLOAD_LEN 2
> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN 4
> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN 5
> +#define UHS2_GO_DORMANT_PAYLOAD_LEN 1
> +
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> + * bit [3:0] : Reserved
> + * bit [6:3] : TMODE(Transfer Mode)
> + * bit 3: DAM(Data Access Mode)
> + * bit 4: TLUM(TLEN Unit Mode)
> + * bit 5: LM(Length Mode)
> + * bit 6: DM(Duplex Mode)
> + * bit [7] : R/W(Read/Write)
> + * 0: Control read command
> + * 1: Control write command
> + * bit [15:8] : Reserved
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_DCMD_DM_POS 6
> +#define UHS2_DCMD_2L_HD_MODE (1 << UHS2_DCMD_DM_POS)
> +#define UHS2_DCMD_LM_POS 5
> +#define UHS2_DCMD_LM_TLEN_EXIST (1 << UHS2_DCMD_LM_POS)
> +#define UHS2_DCMD_TLUM_POS 4
> +#define UHS2_DCMD_TLUM_BYTE_MODE (1 << UHS2_DCMD_TLUM_POS)
> +#define UHS2_NATIVE_DCMD_DAM_POS 3
> +#define UHS2_NATIVE_DCMD_DAM_IO (1 << UHS2_NATIVE_DCMD_DAM_POS)
> +
> +#define UHS2_RES_NACK_POS 7
> +#define UHS2_RES_NACK_MASK (0x1 << UHS2_RES_NACK_POS)
> +
> +#define UHS2_RES_ECODE_POS 4
> +#define UHS2_RES_ECODE_MASK 0x7
> +#define UHS2_RES_ECODE_COND 1
> +#define UHS2_RES_ECODE_ARG 2
> +#define UHS2_RES_ECODE_GEN 3
> +
> +/* IOADR of device registers */
> +#define UHS2_IOADR_GENERIC_CAPS 0x00
> +#define UHS2_IOADR_PHY_CAPS 0x02
> +#define UHS2_IOADR_LINK_CAPS 0x04
> +#define UHS2_IOADR_RSV_CAPS 0x06
> +#define UHS2_IOADR_GENERIC_SETTINGS 0x08
> +#define UHS2_IOADR_PHY_SETTINGS 0x0A
> +#define UHS2_IOADR_LINK_SETTINGS 0x0C
> +#define UHS2_IOADR_PRESET 0x40
> +
> +/* SD application packets */
> +#define UHS2_SD_CMD_INDEX_POS 8
> +
> +#define UHS2_SD_CMD_APP_POS 14
> +#define UHS2_SD_CMD_APP (1 << UHS2_SD_CMD_APP_POS)
> +
> +/* UHS-II Device Registers */
> +#define UHS2_DEV_CONFIG_REG 0x000
> +
> +/* General Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_GEN_CAPS (UHS2_DEV_CONFIG_REG + 0x000)
> +#define UHS2_DEV_CONFIG_N_LANES_POS 8
> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> +#define UHS2_DEV_CONFIG_2L_HD_FD 0x1
> +#define UHS2_DEV_CONFIG_2D1U_FD 0x2
> +#define UHS2_DEV_CONFIG_1D2U_FD 0x4
> +#define UHS2_DEV_CONFIG_2D2U_FD 0x8
> +#define UHS2_DEV_CONFIG_DADR_POS 14
> +#define UHS2_DEV_CONFIG_DADR_MASK 0x1
> +#define UHS2_DEV_CONFIG_APP_POS 16
> +#define UHS2_DEV_CONFIG_APP_MASK 0xFF
> +#define UHS2_DEV_CONFIG_APP_SD_MEM 0x1
> +
> +#define UHS2_DEV_CONFIG_GEN_SET (UHS2_DEV_CONFIG_REG + 0x008)
> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS 8
> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD 0x0
> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD 0x2
> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD 0x3
> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD 0x4
> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> +
> +/* PHY Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_PHY_CAPS (UHS2_DEV_CONFIG_REG + 0x002)
> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK 0xF
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS 4
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK 0x3
> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS 15
> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK 0x1
> +#define UHS2_DEV_CONFIG_PHY_CAPS1 (UHS2_DEV_CONFIG_REG + 0x003)
> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK 0xF
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS 4
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK 0xF
> +
> +#define UHS2_DEV_CONFIG_PHY_SET (UHS2_DEV_CONFIG_REG + 0x00A)
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS 6
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A 0x0
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B 0x1
> +
> +/* LINK-TRAN Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS (UHS2_DEV_CONFIG_REG + 0x004)
> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK 0xF
> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS 4
> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK 0x3
> +#define UHS2_DEV_CONFIG_N_FCU_POS 8
> +#define UHS2_DEV_CONFIG_N_FCU_MASK 0xFF
> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS 16
> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK 0x7
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS 20
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK 0xFFF
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1 (UHS2_DEV_CONFIG_REG + 0x005)
> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK 0xFF
> +
> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET (UHS2_DEV_CONFIG_REG + 0x00C)
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN 0x200
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> +
> +/* Preset register */
> +#define UHS2_DEV_CONFIG_PRESET (UHS2_DEV_CONFIG_REG + 0x040)
> +
> +#define UHS2_DEV_INT_REG 0x100
> +
> +#define UHS2_DEV_STATUS_REG 0x180
> +
> +#define UHS2_DEV_CMD_REG 0x200
> +#define UHS2_DEV_CMD_FULL_RESET (UHS2_DEV_CMD_REG + 0x000)
> +#define UHS2_DEV_CMD_GO_DORMANT_STATE (UHS2_DEV_CMD_REG + 0x001)
> +#define UHS2_DEV_CMD_DORMANT_HIBER BIT(7)
> +#define UHS2_DEV_CMD_DEVICE_INIT (UHS2_DEV_CMD_REG + 0x002)
> +#define UHS2_DEV_INIT_COMPLETE_FLAG BIT(11)
> +#define UHS2_DEV_CMD_ENUMERATE (UHS2_DEV_CMD_REG + 0x003)
> +#define UHS2_DEV_CMD_TRANS_ABORT (UHS2_DEV_CMD_REG + 0x004)
> +
> +#define UHS2_RCLK_MAX 52000000
> +#define UHS2_RCLK_MIN 26000000
> +
> +#endif /* LINUX_MMC_UHS2_H */
Kind regards
Uffe
