On 5/31/23 15:13, Adrian Hunter wrote:
On 31/05/23 14:34, Marek Vasut wrote:
On 5/31/23 07:46, Adrian Hunter wrote:
On 31/05/23 03:27, Marek Vasut wrote:
This reverts commit 08ebf903af57cda6d773f3dd1671b64f73b432b8.
On STM32MP153C DHCOR DRC Compact with microSD card
Kingston Canvas Go! Plus MicroSDXC I 64 GiB U3/V30/A2 SDCG3/64GB
it is no longer possible to mount ext4 filesystem.
Git bisect points to this commit which is being reverted here. A bit of
investigation shows that for non-working microSD cards
cache_enabled=TRUE fua_enabled=false
For working microSD card (Kingston Canvas React Plus, MicroSDXC II
64 GiB U3/V90/A1 SDCR2/64GB)
cache_enabled=FALSE fua_enabled=false
It seems enabling the cache for SD cards causes the issue. Before the
reverted commit, the cache was not reported enabled for SD cards. I am
not sure whether such blunt revert is the correct solution however, any
ideas ?
This does not disable the cache, it disables the block layer from issuing
cache flushes (by telling it there is no cache being used).
It would be good to know what commands are failing, which should be visible
in the kernel messages if dynamic debug is enabled:
Dynamic debug for mmc
---------------------
Kernel must be configured:
CONFIG_DYNAMIC_DEBUG=y
To enable mmc debug via sysfs:
echo 'file drivers/mmc/core/* +p' > /sys/kernel/debug/dynamic_debug/control
echo 'file drivers/mmc/host/* +p' > /sys/kernel/debug/dynamic_debug/control
To enable mmc debug via kernel command line:
dyndbg="file drivers/mmc/core/* +p;file drivers/mmc/host/* +p"
To disable mmc debug:
echo 'file drivers/mmc/core/* -p' > /sys/kernel/debug/dynamic_debug/control
echo 'file drivers/mmc/host/* -p' > /sys/kernel/debug/dynamic_debug/control
More general information in kernel documentation in kernel tree:
Documentation/admin-guide/dynamic-debug-howto.rst
Log is below, I added newlines around the mount failure.
Do you see anything problematic there ?
$ echo 'file drivers/mmc/core/* +p' > /sys/kernel/debug/dynamic_debug/control ; echo 'file drivers/mmc/host/* +p' > /sys/kernel/debug/dynamic_debug/control ; echo 8 > /proc/sys/kernel/printk ; mount /dev/mmcblk1p4 /mnt
[ 61.061029] <mmc1: starting CMD23 arg 00000002 flags 00000015>
[ 61.065637] mmc1: starting CMD18 arg 00002002 flags 000000b5
[ 61.071144] mmc1: blksz 512 blocks 2 flags 00000200 tsac 100 ms nsac 0
[ 61.078096] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.083302] mmci-pl18x 58005000.mmc: blksz 0200 blks 0002 flags 00000200
[ 61.090012] mmci-pl18x 58005000.mmc: op 17 arg 00000002 flags 00000015
[ 61.096531] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.102332] mmci-pl18x 58005000.mmc: op 12 arg 00002002 flags 000000b5
[ 61.108836] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.114575] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.120371] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.127178] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.134084] mmc1: 1024 bytes transferred: 0
[ 61.138658] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.145533] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.150946] mmc1: starting CMD18 arg 00002000 flags 000000b5
[ 61.156609] mmc1: blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
[ 61.163426] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.168759] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000200
[ 61.175368] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.181985] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.187682] mmci-pl18x 58005000.mmc: op 12 arg 00002000 flags 000000b5
[ 61.194185] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.199979] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.205769] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.212574] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.219478] mmc1: 4096 bytes transferred: 0
[ 61.224050] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.231166] <mmc1: starting CMD23 arg 00000002 flags 00000015>
[ 61.236378] mmc1: starting CMD18 arg 00002002 flags 000000b5
[ 61.241983] mmc1: blksz 512 blocks 2 flags 00000200 tsac 100 ms nsac 0
[ 61.248940] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.254169] mmci-pl18x 58005000.mmc: blksz 0200 blks 0002 flags 00000200
[ 61.260779] mmci-pl18x 58005000.mmc: op 17 arg 00000002 flags 00000015
[ 61.267405] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.273101] mmci-pl18x 58005000.mmc: op 12 arg 00002002 flags 000000b5
[ 61.279603] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.285431] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.291125] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.298032] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.304937] mmc1: 1024 bytes transferred: 0
[ 61.309409] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.316256] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.321768] mmc1: starting CMD18 arg 00002000 flags 000000b5
[ 61.327459] mmc1: blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
[ 61.334360] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.339459] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000200
[ 61.346167] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.352782] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.358478] mmci-pl18x 58005000.mmc: op 12 arg 00002000 flags 000000b5
[ 61.365082] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.370776] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.376565] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.383371] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.390275] mmc1: 4096 bytes transferred: 0
[ 61.394848] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.401885] <mmc1: starting CMD23 arg 00000002 flags 00000015>
[ 61.407193] mmc1: starting CMD18 arg 00002002 flags 000000b5
[ 61.412794] mmc1: blksz 512 blocks 2 flags 00000200 tsac 100 ms nsac 0
[ 61.419748] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.424973] mmci-pl18x 58005000.mmc: blksz 0200 blks 0002 flags 00000200
[ 61.431582] mmci-pl18x 58005000.mmc: op 17 arg 00000002 flags 00000015
[ 61.438204] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.443901] mmci-pl18x 58005000.mmc: op 12 arg 00002002 flags 000000b5
[ 61.450404] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.456232] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.461927] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.468834] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.475739] mmc1: 1024 bytes transferred: 0
[ 61.480210] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.487054] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.492462] mmc1: starting CMD18 arg 00002000 flags 000000b5
[ 61.498251] mmc1: blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
[ 61.505160] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.510260] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000200
[ 61.516969] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.523592] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.529288] mmci-pl18x 58005000.mmc: op 12 arg 00002000 flags 000000b5
[ 61.535789] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.541583] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.547271] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.554177] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.561082] mmc1: 4096 bytes transferred: 0
[ 61.565654] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.572440] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.578017] mmc1: starting CMD18 arg 00002008 flags 000000b5
[ 61.583653] mmc1: blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
[ 61.590465] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.595686] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000200
[ 61.602396] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.608915] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.614712] mmci-pl18x 58005000.mmc: op 12 arg 00002008 flags 000000b5
[ 61.621215] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.627034] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.632727] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.639633] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.646437] mmc1: 4096 bytes transferred: 0
[ 61.651010] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.658908] <mmc1: starting CMD23 arg 00000108 flags 00000015>
[ 61.663421] mmc1: starting CMD18 arg 00003be8 flags 000000b5
[ 61.669102] mmc1: blksz 512 blocks 264 flags 00000200 tsac 100 ms nsac 0
[ 61.676155] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.681355] mmci-pl18x 58005000.mmc: blksz 0200 blks 0108 flags 00000200
[ 61.688064] mmci-pl18x 58005000.mmc: op 17 arg 00000108 flags 00000015
[ 61.694589] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.700284] mmci-pl18x 58005000.mmc: op 12 arg 00003be8 flags 000000b5
[ 61.706887] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.712581] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.718372] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000100
[ 61.724060] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.730965] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.737870] mmc1: 135168 bytes transferred: 0
[ 61.742544] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.749064] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.755336] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.760649] mmc1: starting CMD18 arg 00442000 flags 000000b5
[ 61.766327] mmc1: blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
[ 61.773144] mmc1: CMD12 arg 00000000 flags 00000095
[ 61.778489] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000200
[ 61.785100] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.791616] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.797414] mmci-pl18x 58005000.mmc: op 12 arg 00442000 flags 000000b5
[ 61.803916] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.809710] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.815399] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.822306] mmc1: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 61.829211] mmc1: 4096 bytes transferred: 0
[ 61.833683] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.833952] mmc0: starting CMD7 arg fffd0000 flags 00000015
[ 61.840205] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.845820] mmci-pl18x 48004000.mmc: op 07 arg fffd0000 flags 00000015
[ 61.853036] <mmc1: starting CMD23 arg 00000008 flags 00000015>
[ 61.858074] mmci-pl18x 48004000.mmc: irq0 (data+cmd) 00000040
[ 61.858098] mmc0: req done (CMD7): 0: 00001ed7 00000000 00000000 00000000
[ 61.876506] mmc1: starting CMD25 arg 00002000 flags 000000b5
[ 61.882106] mmc1: blksz 512 blocks 8 flags 00000100 tsac 3000 ms nsac 0
[ 61.889107] mmc1: CMD12 arg 00000000 flags 0000049d
[ 61.894346] mmci-pl18x 58005000.mmc: blksz 0200 blks 0008 flags 00000100
[ 61.900957] mmci-pl18x 58005000.mmc: op 17 arg 00000008 flags 00000015
[ 61.907588] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.913283] mmci-pl18x 58005000.mmc: op 19 arg 00002000 flags 000000b5
[ 61.919786] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.925612] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000140
[ 61.931309] mmc1: req done <CMD23>: 0: 00000900 00000000 00000000 00000000
[ 61.938219] mmc1: req done (CMD25): 0: 00000900 00000000 00000000 00000000
[ 61.945125] mmc1: 4096 bytes transferred: 0
[ 61.949598] mmc1: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 61.956107] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.961888] mmc1: starting CMD13 arg 50480000 flags 00000195
[ 61.967581] mmci-pl18x 58005000.mmc: op 0d arg 50480000 flags 00000195
[ 61.974026] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 61.979718] mmc1: req done (CMD13): 0: 00000900 00000000 00000000 00000000
[ 61.986630] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 61.992588] mmc1: starting CMD49 arg 10020a00 flags 00000035
[ 61.998152] mmc1: blksz 512 blocks 1 flags 00000100 tsac 3000 ms nsac 0
[ 62.005158] mmci-pl18x 58005000.mmc: blksz 0200 blks 0001 flags 00000100
[ 62.011778] mmci-pl18x 58005000.mmc: op 31 arg 10020a00 flags 00000035
[ 62.018317] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 62.024011] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000100
[ 62.029801] mmc1: req done (CMD49): 0: 00000900 00000000 00000000 00000000
[ 62.036708] mmc1: 512 bytes transferred: 0
[ 62.041083] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
[ 62.046988] mmc1: starting CMD48 arg 10020a00 flags 000000b5
[ 62.052487] mmc1: blksz 512 blocks 1 flags 00000200 tsac 100 ms nsac 0
[ 62.059443] mmci-pl18x 58005000.mmc: blksz 0200 blks 0001 flags 00000200
[ 62.066154] mmci-pl18x 58005000.mmc: op 30 arg 10020a00 flags 000000b5
[ 62.072688] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000040
[ 62.078382] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000100
[ 62.084173] mmc1: req done (CMD48): 0: 00000900 00000000 00000000 00000000
[ 62.091081] mmc1: 512 bytes transferred: 0
[ 62.095455] mmci-pl18x 58005000.mmc: irq0 (data+cmd) 00000000
CMD48 was successful but it still became an error, which must have
been because it indicated the flush had not completed. We do not
allow for mmc_poll_for_busy() being too quick i.e. card has not
had a chance to indicate busy yet.
Please try this:
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 72b664ed90cf..9c3123867a99 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -1313,6 +1313,8 @@ static int sd_flush_cache(struct mmc_host *host)
{
struct mmc_card *card = host->card;
u8 *reg_buf, fno, page;
+ unsigned long timeout;
+ bool expired;
u16 offset;
int err;
@@ -1338,11 +1340,15 @@ static int sd_flush_cache(struct mmc_host *host)
goto out;
}
+ timeout = jiffies + msecs_to_jiffies(SD_WRITE_EXTR_SINGLE_TIMEOUT_MS) + 1;
+again:
err = mmc_poll_for_busy(card, SD_WRITE_EXTR_SINGLE_TIMEOUT_MS, false,
MMC_BUSY_EXTR_SINGLE);
if (err)
goto out;
+ expired = time_after(jiffies, timeout);
+
/*
* Read the Flush Cache bit. The card shall reset it, to confirm that
* it's has completed the flushing of the cache.
@@ -1354,8 +1360,12 @@ static int sd_flush_cache(struct mmc_host *host)
goto out;
}
- if (reg_buf[0] & BIT(0))
- err = -ETIMEDOUT;
+ if (reg_buf[0] & BIT(0)) {
I am getting here, multiple times, with expired=0 .
After that, once, I get here with expired=1 and then the ext4 mount
failure occurs.
+ if (expired)
+ err = -ETIMEDOUT;
+ else
+ goto again;
+ }
out:
kfree(reg_buf);
return err;
Also, I made another observation -- if I reduce the SD bus clock
frequency to 10 MHz (current is 50 MHz), then I don't observe this problem.