From: Arnd Bergmann <arnd@xxxxxxxx>
All Atmel (now Microchip) machines boot using DT, so the
old platform_data for this driver is no longer used by any
boards.
Removing the pdata probe lets us simplify the GPIO handling
with the use of the descriptor API.
Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx>
---
drivers/mmc/host/atmel-mci.c | 179 +++++++++++++++--------------------
include/linux/atmel-mci.h | 46 ---------
2 files changed, 77 insertions(+), 148 deletions(-)
delete mode 100644 include/linux/atmel-mci.h
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index bb9bbf1c927b..40006a960277 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -30,7 +30,6 @@
#include <linux/mmc/host.h>
#include <linux/mmc/sdio.h>
-#include <linux/atmel-mci.h>
#include <linux/atmel_pdc.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
@@ -40,6 +39,30 @@
#include <asm/io.h>
#include <asm/unaligned.h>
+#define ATMCI_MAX_NR_SLOTS 2
+
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ * @detect_is_active_high: The state of the detect pin when it is active
+ * @non_removable: The slot is not removable, only detect once
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ *
+ * Note that support for multiple slots is experimental -- some cards
+ * might get upset if we don't get the clock management exactly right.
+ * But in most cases, it should work just fine.
+ */
+struct mci_slot_pdata {
+ unsigned int bus_width;
+ bool detect_is_active_high;
+ bool non_removable;
+};
+
/*
* Superset of MCI IP registers integrated in Atmel AT91 Processor
* Registers and bitfields marked with [2] are only available in MCI2
@@ -388,8 +411,8 @@ struct atmel_mci_slot {
#define ATMCI_CARD_NEED_INIT 1
#define ATMCI_SHUTDOWN 2
- int detect_pin;
- int wp_pin;
+ struct gpio_desc *detect_pin;
+ struct gpio_desc *wp_pin;
bool detect_is_active_high;
struct timer_list detect_timer;
@@ -593,7 +616,6 @@ static void atmci_init_debugfs(struct atmel_mci_slot *slot)
&host->completed_events);
}
-#if defined(CONFIG_OF)
static const struct of_device_id atmci_dt_ids[] = {
{ .compatible = "atmel,hsmci" },
{ /* sentinel */ }
@@ -601,23 +623,13 @@ static const struct of_device_id atmci_dt_ids[] = {
MODULE_DEVICE_TABLE(of, atmci_dt_ids);
-static struct mci_platform_data*
-atmci_of_init(struct platform_device *pdev)
+static int
+atmci_of_init(struct platform_device *pdev, struct mci_slot_pdata *pdata)
{
struct device_node *np = pdev->dev.of_node;
struct device_node *cnp;
- struct mci_platform_data *pdata;
u32 slot_id;
- if (!np) {
- dev_err(&pdev->dev, "device node not found\n");
- return ERR_PTR(-EINVAL);
- }
-
- pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
- if (!pdata)
- return ERR_PTR(-ENOMEM);
-
for_each_child_of_node(np, cnp) {
if (of_property_read_u32(cnp, "reg", &slot_id)) {
dev_warn(&pdev->dev, "reg property is missing for %pOF\n",
@@ -633,31 +645,18 @@ atmci_of_init(struct platform_device *pdev)
}
if (of_property_read_u32(cnp, "bus-width",
- &pdata->slot[slot_id].bus_width))
- pdata->slot[slot_id].bus_width = 1;
-
- pdata->slot[slot_id].detect_pin =
- of_get_named_gpio(cnp, "cd-gpios", 0);
+ &pdata[slot_id].bus_width))
+ pdata[slot_id].bus_width = 1;
- pdata->slot[slot_id].detect_is_active_high =
+ pdata[slot_id].detect_is_active_high =
of_property_read_bool(cnp, "cd-inverted");
- pdata->slot[slot_id].non_removable =
+ pdata[slot_id].non_removable =
of_property_read_bool(cnp, "non-removable");
-
- pdata->slot[slot_id].wp_pin =
- of_get_named_gpio(cnp, "wp-gpios", 0);
}
- return pdata;
-}
-#else /* CONFIG_OF */
-static inline struct mci_platform_data*
-atmci_of_init(struct platform_device *dev)
-{
- return ERR_PTR(-EINVAL);
+ return 0;
}
-#endif
static inline unsigned int atmci_get_version(struct atmel_mci *host)
{
@@ -1509,8 +1508,8 @@ static int atmci_get_ro(struct mmc_host *mmc)
int read_only = -ENOSYS;
struct atmel_mci_slot *slot = mmc_priv(mmc);
- if (gpio_is_valid(slot->wp_pin)) {
- read_only = gpio_get_value(slot->wp_pin);
+ if (slot->wp_pin) {
+ read_only = gpiod_get_value(slot->wp_pin);
dev_dbg(&mmc->class_dev, "card is %s\n",
read_only ? "read-only" : "read-write");
}
@@ -1523,8 +1522,8 @@ static int atmci_get_cd(struct mmc_host *mmc)
int present = -ENOSYS;
struct atmel_mci_slot *slot = mmc_priv(mmc);
- if (gpio_is_valid(slot->detect_pin)) {
- present = !(gpio_get_value(slot->detect_pin) ^
+ if (slot->detect_pin) {
+ present = !(gpiod_get_value(slot->detect_pin) ^
slot->detect_is_active_high);
dev_dbg(&mmc->class_dev, "card is %spresent\n",
present ? "" : "not ");
@@ -1637,8 +1636,8 @@ static void atmci_detect_change(struct timer_list *t)
if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
return;
- enable_irq(gpio_to_irq(slot->detect_pin));
- present = !(gpio_get_value(slot->detect_pin) ^
+ enable_irq(gpiod_to_irq(slot->detect_pin));
+ present = !(gpiod_get_value(slot->detect_pin) ^
slot->detect_is_active_high);
present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
@@ -2231,18 +2230,15 @@ static int atmci_init_slot(struct atmel_mci *host,
slot = mmc_priv(mmc);
slot->mmc = mmc;
slot->host = host;
- slot->detect_pin = slot_data->detect_pin;
- slot->wp_pin = slot_data->wp_pin;
slot->detect_is_active_high = slot_data->detect_is_active_high;
slot->sdc_reg = sdc_reg;
slot->sdio_irq = sdio_irq;
dev_dbg(&mmc->class_dev,
- "slot[%u]: bus_width=%u, detect_pin=%d, "
- "detect_is_active_high=%s, wp_pin=%d\n",
- id, slot_data->bus_width, slot_data->detect_pin,
- slot_data->detect_is_active_high ? "true" : "false",
- slot_data->wp_pin);
+ "slot[%u]: bus_width=%u, "
+ "detect_is_active_high=%s\n",
+ id, slot_data->bus_width,
+ slot_data->detect_is_active_high ? "true" : "false");
mmc->ops = &atmci_ops;
mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
@@ -2278,30 +2274,29 @@ static int atmci_init_slot(struct atmel_mci *host,
/* Assume card is present initially */
set_bit(ATMCI_CARD_PRESENT, &slot->flags);
- if (gpio_is_valid(slot->detect_pin)) {
- if (devm_gpio_request(&host->pdev->dev, slot->detect_pin,
- "mmc_detect")) {
- dev_dbg(&mmc->class_dev, "no detect pin available\n");
- slot->detect_pin = -EBUSY;
- } else if (gpio_get_value(slot->detect_pin) ^
- slot->detect_is_active_high) {
+
+ slot->detect_pin = devm_gpiod_get_optional(&host->pdev->dev, "cd", GPIOD_IN);
+ if (!IS_ERR(slot->detect_pin)) {
+ dev_dbg(&mmc->class_dev, "no detect pin available\n");
+ slot->detect_pin = NULL;
+ } else if (slot->detect_pin) {
+ if (gpiod_get_value(slot->detect_pin) ^
+ slot->detect_is_active_high) {
clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
}
}
- if (!gpio_is_valid(slot->detect_pin)) {
+ if (!slot->detect_pin) {
if (slot_data->non_removable)
mmc->caps |= MMC_CAP_NONREMOVABLE;
else
mmc->caps |= MMC_CAP_NEEDS_POLL;
}
- if (gpio_is_valid(slot->wp_pin)) {
- if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
- "mmc_wp")) {
- dev_dbg(&mmc->class_dev, "no WP pin available\n");
- slot->wp_pin = -EBUSY;
- }
+ slot->wp_pin = devm_gpiod_get_optional(&host->pdev->dev, "wp", GPIOD_IN);
+ if (IS_ERR(slot->wp_pin)) {
+ dev_dbg(&mmc->class_dev, "no WP pin available\n");
+ slot->wp_pin = NULL;
}
host->slot[id] = slot;
@@ -2312,18 +2307,18 @@ static int atmci_init_slot(struct atmel_mci *host,
return ret;
}
- if (gpio_is_valid(slot->detect_pin)) {
+ if (slot->detect_pin) {
timer_setup(&slot->detect_timer, atmci_detect_change, 0);
- ret = request_irq(gpio_to_irq(slot->detect_pin),
+ ret = request_irq(gpiod_to_irq(slot->detect_pin),
atmci_detect_interrupt,
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
"mmc-detect", slot);
if (ret) {
dev_dbg(&mmc->class_dev,
"could not request IRQ %d for detect pin\n",
- gpio_to_irq(slot->detect_pin));
- slot->detect_pin = -EBUSY;
+ gpiod_to_irq(slot->detect_pin));
+ slot->detect_pin = NULL;
}
}
@@ -2342,10 +2337,8 @@ static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
mmc_remove_host(slot->mmc);
- if (gpio_is_valid(slot->detect_pin)) {
- int pin = slot->detect_pin;
-
- free_irq(gpio_to_irq(pin), slot);
+ if (slot->detect_pin) {
+ free_irq(gpiod_to_irq(slot->detect_pin), slot);
del_timer_sync(&slot->detect_timer);
}
@@ -2357,22 +2350,6 @@ static int atmci_configure_dma(struct atmel_mci *host)
{
host->dma.chan = dma_request_chan(&host->pdev->dev, "rxtx");
- if (PTR_ERR(host->dma.chan) == -ENODEV) {
- struct mci_platform_data *pdata = host->pdev->dev.platform_data;
- dma_cap_mask_t mask;
-
- if (!pdata || !pdata->dma_filter)
- return -ENODEV;
-
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
-
- host->dma.chan = dma_request_channel(mask, pdata->dma_filter,
- pdata->dma_slave);
- if (!host->dma.chan)
- host->dma.chan = ERR_PTR(-ENODEV);
- }
-
if (IS_ERR(host->dma.chan))
return PTR_ERR(host->dma.chan);
@@ -2450,7 +2427,7 @@ static void atmci_get_cap(struct atmel_mci *host)
static int atmci_probe(struct platform_device *pdev)
{
- struct mci_platform_data *pdata;
+ struct mci_slot_pdata pdata[ATMCI_MAX_NR_SLOTS];
struct atmel_mci *host;
struct resource *regs;
unsigned int nr_slots;
@@ -2460,23 +2437,21 @@ static int atmci_probe(struct platform_device *pdev)
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs)
return -ENXIO;
- pdata = pdev->dev.platform_data;
- if (!pdata) {
- pdata = atmci_of_init(pdev);
- if (IS_ERR(pdata)) {
- dev_err(&pdev->dev, "platform data not available\n");
- return PTR_ERR(pdata);
- }
+
+ host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
+ if (!host)
+ return -ENOMEM;
+
+ ret = atmci_of_init(pdev, pdata);
+ if (ret) {
+ dev_err(&pdev->dev, "error parsing DT\n");
+ return ret;
}
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
- host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
- if (!host)
- return -ENOMEM;
-
host->pdev = pdev;
spin_lock_init(&host->lock);
INIT_LIST_HEAD(&host->queue);
@@ -2540,16 +2515,16 @@ static int atmci_probe(struct platform_device *pdev)
/* We need at least one slot to succeed */
nr_slots = 0;
ret = -ENODEV;
- if (pdata->slot[0].bus_width) {
- ret = atmci_init_slot(host, &pdata->slot[0],
+ if (pdata[0].bus_width) {
+ ret = atmci_init_slot(host, &pdata[0],
0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
if (!ret) {
nr_slots++;
host->buf_size = host->slot[0]->mmc->max_req_size;
}
}
- if (pdata->slot[1].bus_width) {
- ret = atmci_init_slot(host, &pdata->slot[1],
+ if (pdata[1].bus_width) {
+ ret = atmci_init_slot(host, &pdata[1],
1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
if (!ret) {
nr_slots++;
@@ -2671,7 +2646,7 @@ static struct platform_driver atmci_driver = {
.driver = {
.name = "atmel_mci",
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
- .of_match_table = of_match_ptr(atmci_dt_ids),
+ .of_match_table = atmci_dt_ids,
.pm = &atmci_dev_pm_ops,
},
};
diff --git a/include/linux/atmel-mci.h b/include/linux/atmel-mci.h
deleted file mode 100644
index 1491af38cc6e..000000000000
--- a/include/linux/atmel-mci.h
+++ /dev/null
@@ -1,46 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __LINUX_ATMEL_MCI_H
-#define __LINUX_ATMEL_MCI_H
-
-#include <linux/types.h>
-#include <linux/dmaengine.h>
-
-#define ATMCI_MAX_NR_SLOTS 2
-
-/**
- * struct mci_slot_pdata - board-specific per-slot configuration
- * @bus_width: Number of data lines wired up the slot
- * @detect_pin: GPIO pin wired to the card detect switch
- * @wp_pin: GPIO pin wired to the write protect sensor
- * @detect_is_active_high: The state of the detect pin when it is active
- * @non_removable: The slot is not removable, only detect once
- *
- * If a given slot is not present on the board, @bus_width should be
- * set to 0. The other fields are ignored in this case.
- *
- * Any pins that aren't available should be set to a negative value.
- *
- * Note that support for multiple slots is experimental -- some cards
- * might get upset if we don't get the clock management exactly right.
- * But in most cases, it should work just fine.
- */
-struct mci_slot_pdata {
- unsigned int bus_width;
- int detect_pin;
- int wp_pin;
- bool detect_is_active_high;
- bool non_removable;
-};
-
-/**
- * struct mci_platform_data - board-specific MMC/SDcard configuration
- * @dma_slave: DMA slave interface to use in data transfers.
- * @slot: Per-slot configuration data.
- */
-struct mci_platform_data {
- void *dma_slave;
- dma_filter_fn dma_filter;
- struct mci_slot_pdata slot[ATMCI_MAX_NR_SLOTS];
-};
-
-#endif /* __LINUX_ATMEL_MCI_H */
--
2.39.0
