[PATCH V6 07/24] mmc: sdhci: add UHS-II related definitions in headers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.

Signed-off-by: Ben Chuang <ben.chuang@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@xxxxxxxxxx>
Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
---
 drivers/mmc/host/sdhci-uhs2.h | 175 ++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sdhci.h      |  62 +++++++++++-
 2 files changed, 236 insertions(+), 1 deletion(-)
 create mode 100644 drivers/mmc/host/sdhci-uhs2.h

diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
new file mode 100644
index 000000000000..29cd91f12b9e
--- /dev/null
+++ b/drivers/mmc/host/sdhci-uhs2.h
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
+ *  Interface driver
+ *
+ * Header file for Host Controller UHS2 related registers.
+ *
+ *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
+ */
+#ifndef __SDHCI_UHS2_H
+#define __SDHCI_UHS2_H
+
+#include <linux/bits.h>
+
+/* SDHCI Category B registers : UHS2 only */
+#define  SDHCI_UHS2_CM_TRAN_RESP	0x10
+#define  SDHCI_UHS2_SD_TRAN_RESP	0x18
+#define  SDHCI_UHS2_SD_TRAN_RESP_1	0x1C
+
+#define SDHCI_UHS2_BLOCK_SIZE	0x80
+#define  SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
+
+#define SDHCI_UHS2_BLOCK_COUNT	0x84
+
+#define SDHCI_UHS2_CMD_PACKET	0x88
+#define  SDHCI_UHS2_CMD_PACK_MAX_LEN	20
+
+#define SDHCI_UHS2_TRANS_MODE	0x9C
+#define  SDHCI_UHS2_TRNS_DMA              BIT(0)
+#define  SDHCI_UHS2_TRNS_BLK_CNT_EN       BIT(1)
+#define  SDHCI_UHS2_TRNS_DATA_TRNS_WRT    BIT(4)
+#define  SDHCI_UHS2_TRNS_BLK_BYTE_MODE    BIT(5)
+#define  SDHCI_UHS2_TRNS_RES_R5           BIT(6)
+#define  SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN BIT(7)
+#define  SDHCI_UHS2_TRNS_RES_INT_DIS      BIT(8)
+#define  SDHCI_UHS2_TRNS_WAIT_EBSY        BIT(14)
+#define  SDHCI_UHS2_TRNS_2L_HD            BIT(15)
+
+#define SDHCI_UHS2_CMD	0x9E
+#define  SDHCI_UHS2_CMD_SUB_CMD       BIT(2)
+#define  SDHCI_UHS2_CMD_DATA          BIT(5)
+#define  SDHCI_UHS2_CMD_TRNS_ABORT    BIT(6)
+#define  SDHCI_UHS2_CMD_CMD12         BIT(7)
+#define  SDHCI_UHS2_CMD_DORMANT       GENMASK(7, 6)
+#define  SDHCI_UHS2_CMD_PACK_LEN_MASK GENMASK(12, 8)
+
+#define SDHCI_UHS2_RESPONSE	0xA0
+#define  SDHCI_UHS2_RESPONSE_MAX_LEN	20
+
+#define SDHCI_UHS2_MSG_SELECT	0xB4
+#define SDHCI_UHS2_MSG_SELECT_CURR	0x0
+#define SDHCI_UHS2_MSG_SELECT_ONE	0x1
+#define SDHCI_UHS2_MSG_SELECT_TWO	0x2
+#define SDHCI_UHS2_MSG_SELECT_THREE	0x3
+
+#define SDHCI_UHS2_MSG		0xB8
+
+#define SDHCI_UHS2_DEV_INT_STATUS	0xBC
+
+#define SDHCI_UHS2_DEV_SELECT		0xBE
+#define SDHCI_UHS2_DEV_SEL_MASK		GENMASK(3, 0)
+#define SDHCI_UHS2_DEV_SEL_INT_MSG_EN	BIT(7)
+
+#define SDHCI_UHS2_DEV_INT_CODE	0xBF
+
+#define SDHCI_UHS2_SW_RESET      0xC0
+#define SDHCI_UHS2_SW_RESET_FULL BIT(0)
+#define SDHCI_UHS2_SW_RESET_SD   BIT(1)
+
+#define SDHCI_UHS2_TIMER_CTRL               0xC2
+#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_MASK GENMASK(7, 4)
+
+#define SDHCI_UHS2_INT_STATUS           0xC4
+#define SDHCI_UHS2_INT_STATUS_ENABLE    0xC8
+#define SDHCI_UHS2_INT_SIGNAL_ENABLE    0xCC
+#define SDHCI_UHS2_INT_HEADER_ERR       BIT(0)
+#define SDHCI_UHS2_INT_RES_ERR          BIT(1)
+#define SDHCI_UHS2_INT_RETRY_EXP        BIT(2)
+#define SDHCI_UHS2_INT_CRC              BIT(3)
+#define SDHCI_UHS2_INT_FRAME_ERR        BIT(4)
+#define SDHCI_UHS2_INT_TID_ERR          BIT(5)
+#define SDHCI_UHS2_INT_UNRECOVER        BIT(7)
+#define SDHCI_UHS2_INT_EBUSY_ERR        BIT(8)
+#define SDHCI_UHS2_INT_ADMA_ERROR       BIT(15)
+#define SDHCI_UHS2_INT_CMD_TIMEOUT      BIT(16)
+#define SDHCI_UHS2_INT_DEADLOCK_TIMEOUT BIT(17)
+#define SDHCI_UHS2_INT_VENDOR_ERR       BIT(27)
+#define SDHCI_UHS2_INT_ERROR_MASK	\
+		(SDHCI_UHS2_INT_HEADER_ERR |	\
+		SDHCI_UHS2_INT_RES_ERR |		\
+		SDHCI_UHS2_INT_RETRY_EXP |	\
+		SDHCI_UHS2_INT_CRC |		\
+		SDHCI_UHS2_INT_FRAME_ERR |	\
+		SDHCI_UHS2_INT_TID_ERR |		\
+		SDHCI_UHS2_INT_UNRECOVER |	\
+		SDHCI_UHS2_INT_EBUSY_ERR |	\
+		SDHCI_UHS2_INT_ADMA_ERROR |	\
+		SDHCI_UHS2_INT_CMD_TIMEOUT |	\
+		SDHCI_UHS2_INT_DEADLOCK_TIMEOUT)
+#define SDHCI_UHS2_INT_CMD_ERR_MASK	\
+		(SDHCI_UHS2_INT_HEADER_ERR |	\
+		SDHCI_UHS2_INT_RES_ERR |		\
+		SDHCI_UHS2_INT_FRAME_ERR |	\
+		SDHCI_UHS2_INT_TID_ERR |		\
+		SDHCI_UHS2_INT_CMD_TIMEOUT)
+/* CRC Error occurs during a packet receiving */
+#define SDHCI_UHS2_INT_DATA_ERR_MASK	\
+		(SDHCI_UHS2_INT_RETRY_EXP |	\
+		SDHCI_UHS2_INT_CRC |		\
+		SDHCI_UHS2_INT_UNRECOVER |	\
+		SDHCI_UHS2_INT_EBUSY_ERR |	\
+		SDHCI_UHS2_INT_ADMA_ERROR |	\
+		SDHCI_UHS2_INT_DEADLOCK_TIMEOUT)
+
+#define SDHCI_UHS2_SETTINGS_PTR	0xE0
+#define   SDHCI_UHS2_GEN_SETTINGS_POWER_LOW	BIT(0)
+#define   SDHCI_UHS2_GEN_SETTINGS_N_LANES_MASK  GENMASK(11, 8)
+#define   SDHCI_UHS2_FD_OR_2L_HD                0x0 /* 2 lanes */
+#define   SDHCI_UHS2_2D1U_FD                    0x2 /* 3 lanes, 2 down, 1 up, full duplex */
+#define   SDHCI_UHS2_1D2U_FD                    0x3 /* 3 lanes, 1 down, 2 up, full duplex */
+#define   SDHCI_UHS2_2D2U_FD                    0x4 /* 4 lanes, 2 down, 2 up, full duplex */
+
+#define   SDHCI_UHS2_PHY_SET_SPEED_B    BIT(6)
+#define   SDHCI_UHS2_PHY_HIBERNATE_EN   BIT(12)
+#define   SDHCI_UHS2_PHY_N_LSS_SYN_MASK	GENMASK(19, 16)
+#define   SDHCI_UHS2_PHY_N_LSS_DIR_MASK	GENMASK(23, 20)
+
+#define   SDHCI_UHS2_TRAN_N_FCU_MASK       GENMASK(15, 8)
+#define   SDHCI_UHS2_TRAN_RETRY_CNT_MASK   GENMASK(17, 16)
+#define   SDHCI_UHS2_TRAN_1_N_DAT_GAP_MASK GENMASK(7, 0)
+
+#define SDHCI_UHS2_CAPS_PTR	0xE2
+#define  SDHCI_UHS2_CAPS_OFFSET	0
+#define   SDHCI_UHS2_CAPS_DAP_MASK	GENMASK(3, 0)
+#define   SDHCI_UHS2_CAPS_GAP_MASK	GENMASK(7, 4)
+#define   SDHCI_UHS2_CAPS_GAP(gap)	((gap) * 360)
+#define   SDHCI_UHS2_CAPS_LANE_MASK	GENMASK(13, 8)
+#define    SDHCI_UHS2_CAPS_2L_HD_FD	1
+#define    SDHCI_UHS2_CAPS_2D1U_FD	2
+#define    SDHCI_UHS2_CAPS_1D2U_FD	4
+#define    SDHCI_UHS2_CAPS_2D2U_FD	8
+#define   SDHCI_UHS2_CAPS_ADDR_64	BIT(14)
+#define   SDHCI_UHS2_CAPS_BOOT		BIT(15)
+#define   SDHCI_UHS2_CAPS_DEV_TYPE_MASK	GENMASK(17, 16)
+#define    SDHCI_UHS2_CAPS_DEV_TYPE_RMV     0
+#define    SDHCI_UHS2_CAPS_DEV_TYPE_EMB     1
+#define    SDHCI_UHS2_CAPS_DEV_TYPE_EMB_RMV 2
+#define   SDHCI_UHS2_CAPS_NUM_DEV_MASK      GENMASK(21, 18)
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_MASK     GENMASK(23, 22)
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_SHIFT    22
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_P2P      0
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_RING     1
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_HUB      2
+#define   SDHCI_UHS2_CAPS_BUS_TOPO_HUB_RING 3
+
+#define  SDHCI_UHS2_CAPS_PHY_OFFSET	4
+#define   SDHCI_UHS2_CAPS_PHY_REV_MASK       GENMASK(5, 0)
+#define   SDHCI_UHS2_CAPS_PHY_RANGE_MASK     GENMASK(7, 6)
+#define   SDHCI_UHS2_CAPS_PHY_RANGE_A        0
+#define   SDHCI_UHS2_CAPS_PHY_RANGE_B        1
+#define   SDHCI_UHS2_CAPS_PHY_N_LSS_SYN_MASK GENMASK(19, 16)
+#define   SDHCI_UHS2_CAPS_PHY_N_LSS_DIR_MASK GENMASK(23, 20)
+#define  SDHCI_UHS2_CAPS_TRAN_OFFSET	8
+#define   SDHCI_UHS2_CAPS_TRAN_LINK_REV_MASK  GENMASK(5, 0)
+#define   SDHCI_UHS2_CAPS_TRAN_N_FCU_MASK     GENMASK(15, 8)
+#define   SDHCI_UHS2_CAPS_TRAN_HOST_TYPE_MASK GENMASK(18, 16)
+#define   SDHCI_UHS2_CAPS_TRAN_BLK_LEN_MASK   GENMASK(31, 20)
+
+#define  SDHCI_UHS2_CAPS_TRAN_1_OFFSET	        12
+#define  SDHCI_UHS2_CAPS_TRAN_1_N_DATA_GAP_MASK	GENMASK(7, 0)
+
+#define SDHCI_UHS2_EMBED_CTRL_PTR 0xE6
+#define SDHCI_UHS2_VENDOR_PTR     0xE8
+
+#endif /* __SDHCI_UHS2_H */
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 605eaee805f7..40125ecd4e3f 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -43,8 +43,23 @@
 #define  SDHCI_TRNS_READ	0x10
 #define  SDHCI_TRNS_MULTI	0x20
 
+/*
+ * Defined in Host Version 4.0.
+ */
+#define  SDHCI_TRNS_RES_TYPE		0x40
+#define  SDHCI_TRNS_RES_ERR_CHECK	0x80
+#define  SDHCI_TRNS_RES_INT_DIS		0x0100
+
 #define SDHCI_COMMAND		0x0E
 #define  SDHCI_CMD_RESP_MASK	0x03
+
+/*
+ * Host Version 4.10 adds this bit to distinguish a main command or
+ * sub command.
+ * For example with SDIO, CMD52 (sub command) issued during CMD53 (main command).
+ */
+#define  SDHCI_CMD_SUB_CMD	0x04
+
 #define  SDHCI_CMD_CRC		0x08
 #define  SDHCI_CMD_INDEX	0x10
 #define  SDHCI_CMD_DATA		0x20
@@ -65,6 +80,9 @@
 #define SDHCI_PRESENT_STATE	0x24
 #define  SDHCI_CMD_INHIBIT	0x00000001
 #define  SDHCI_DATA_INHIBIT	0x00000002
+
+#define  SDHCI_DAT_4_TO_7_LVL_MASK	0x000000F0
+
 #define  SDHCI_DOING_WRITE	0x00000100
 #define  SDHCI_DOING_READ	0x00000200
 #define  SDHCI_SPACE_AVAILABLE	0x00000400
@@ -80,6 +98,15 @@
 #define   SDHCI_DATA_0_LVL_MASK	0x00100000
 #define  SDHCI_CMD_LVL		0x01000000
 
+/* Host Version 4.10 */
+
+#define  SDHCI_HOST_REGULATOR_STABLE	0x02000000
+#define  SDHCI_CMD_NOT_ISSUED_ERR	0x08000000
+#define  SDHCI_SUB_CMD_STATUS		0x10000000
+#define  SDHCI_UHS2_IN_DORMANT_STATE	0x20000000
+#define  SDHCI_UHS2_LANE_SYNC		0x40000000
+#define  SDHCI_UHS2_IF_DETECT		0x80000000
+
 #define SDHCI_HOST_CONTROL	0x28
 #define  SDHCI_CTRL_LED		0x01
 #define  SDHCI_CTRL_4BITBUS	0x02
@@ -100,6 +127,14 @@
 #define  SDHCI_POWER_300	0x0C
 #define  SDHCI_POWER_330	0x0E
 
+/*
+ * VDD2 - UHS2
+ * VDD2 power on/off and voltage select (UHS2)
+ */
+#define  SDHCI_VDD2_POWER_ON		0x10
+#define  SDHCI_VDD2_POWER_120		0x80
+#define  SDHCI_VDD2_POWER_180		0xA0
+
 #define SDHCI_BLOCK_GAP_CONTROL	0x2A
 
 #define SDHCI_WAKE_UP_CONTROL	0x2B
@@ -110,7 +145,7 @@
 #define SDHCI_CLOCK_CONTROL	0x2C
 #define  SDHCI_DIVIDER_SHIFT	8
 #define  SDHCI_DIVIDER_HI_SHIFT	6
-#define  SDHCI_DIV_MASK	0xFF
+#define  SDHCI_DIV_MASK		0xFF
 #define  SDHCI_DIV_MASK_LEN	8
 #define  SDHCI_DIV_HI_MASK	0x300
 #define  SDHCI_PROG_CLOCK_MODE	0x0020
@@ -139,6 +174,10 @@
 #define  SDHCI_INT_CARD_REMOVE	0x00000080
 #define  SDHCI_INT_CARD_INT	0x00000100
 #define  SDHCI_INT_RETUNE	0x00001000
+
+/* Host Version 4.10 */
+#define  SDHCI_INT_FX_EVENT	0x00002000
+
 #define  SDHCI_INT_CQE		0x00004000
 #define  SDHCI_INT_ERROR	0x00008000
 #define  SDHCI_INT_TIMEOUT	0x00010000
@@ -152,6 +191,9 @@
 #define  SDHCI_INT_AUTO_CMD_ERR	0x01000000
 #define  SDHCI_INT_ADMA_ERROR	0x02000000
 
+/* Host Version 4.0 */
+#define  SDHCI_INT_RESP_ERR	0x08000000
+
 #define  SDHCI_INT_NORMAL_MASK	0x00007FFF
 #define  SDHCI_INT_ERROR_MASK	0xFFFF8000
 
@@ -178,6 +220,9 @@
 #define  SDHCI_AUTO_CMD_END_BIT	0x00000008
 #define  SDHCI_AUTO_CMD_INDEX	0x00000010
 
+/* Host Version 4.10 */
+#define  SDHCI_AUTO_CMD_RESP_ERR	0x0020
+
 #define SDHCI_HOST_CONTROL2		0x3E
 #define  SDHCI_CTRL_UHS_MASK		0x0007
 #define   SDHCI_CTRL_UHS_SDR12		0x0000
@@ -186,6 +231,7 @@
 #define   SDHCI_CTRL_UHS_SDR104		0x0003
 #define   SDHCI_CTRL_UHS_DDR50		0x0004
 #define   SDHCI_CTRL_HS400		0x0005 /* Non-standard */
+#define   SDHCI_CTRL_UHS2		0x0007
 #define  SDHCI_CTRL_VDD_180		0x0008
 #define  SDHCI_CTRL_DRV_TYPE_MASK	0x0030
 #define   SDHCI_CTRL_DRV_TYPE_B		0x0000
@@ -194,9 +240,12 @@
 #define   SDHCI_CTRL_DRV_TYPE_D		0x0030
 #define  SDHCI_CTRL_EXEC_TUNING		0x0040
 #define  SDHCI_CTRL_TUNED_CLK		0x0080
+#define  SDHCI_CTRL_UHS2_ENABLE		0x0100
+#define  SDHCI_CTRL_ADMA2_LEN_MODE	0x0400
 #define  SDHCI_CMD23_ENABLE		0x0800
 #define  SDHCI_CTRL_V4_MODE		0x1000
 #define  SDHCI_CTRL_64BIT_ADDR		0x2000
+#define  SDHCI_CTRL_ASYNC_INT_ENABLE	0x4000
 #define  SDHCI_CTRL_PRESET_VAL_ENABLE	0x8000
 
 #define SDHCI_CAPABILITIES	0x40
@@ -219,11 +268,13 @@
 #define  SDHCI_CAN_VDD_180	0x04000000
 #define  SDHCI_CAN_64BIT_V4	0x08000000
 #define  SDHCI_CAN_64BIT	0x10000000
+#define  SDHCI_CAN_ASYNC_INT	0x20000000
 
 #define SDHCI_CAPABILITIES_1	0x44
 #define  SDHCI_SUPPORT_SDR50	0x00000001
 #define  SDHCI_SUPPORT_SDR104	0x00000002
 #define  SDHCI_SUPPORT_DDR50	0x00000004
+#define  SDHCI_SUPPORT_UHS2	0x00000008
 #define  SDHCI_DRIVER_TYPE_A	0x00000010
 #define  SDHCI_DRIVER_TYPE_C	0x00000020
 #define  SDHCI_DRIVER_TYPE_D	0x00000040
@@ -232,6 +283,7 @@
 #define  SDHCI_RETUNING_MODE_MASK		GENMASK(15, 14)
 #define  SDHCI_CLOCK_MUL_MASK			GENMASK(23, 16)
 #define  SDHCI_CAN_DO_ADMA3	0x08000000
+#define  SDHCI_CAN_VDD2_180	0x10000000 /* UHS-2 1.8V VDD2 */
 #define  SDHCI_SUPPORT_HS400	0x80000000 /* Non-standard */
 
 #define SDHCI_MAX_CURRENT		0x48
@@ -239,11 +291,14 @@
 #define  SDHCI_MAX_CURRENT_330_MASK	GENMASK(7, 0)
 #define  SDHCI_MAX_CURRENT_300_MASK	GENMASK(15, 8)
 #define  SDHCI_MAX_CURRENT_180_MASK	GENMASK(23, 16)
+#define SDHCI_MAX_CURRENT_1		0x4C
+#define  SDHCI_MAX_CURRENT_VDD2_180_MASK	GENMASK(7, 0) /* UHS2 */
 #define   SDHCI_MAX_CURRENT_MULTIPLIER	4
 
 /* 4C-4F reserved for more max current */
 
 #define SDHCI_SET_ACMD12_ERROR	0x50
+/* Host Version 4.10 */
 #define SDHCI_SET_INT_ERROR	0x52
 
 #define SDHCI_ADMA_ERROR	0x54
@@ -262,10 +317,15 @@
 #define SDHCI_PRESET_FOR_SDR104        0x6C
 #define SDHCI_PRESET_FOR_DDR50 0x6E
 #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
+
+/* UHS2 */
+#define SDHCI_PRESET_FOR_UHS2  0x74
 #define SDHCI_PRESET_DRV_MASK		GENMASK(15, 14)
 #define SDHCI_PRESET_CLKGEN_SEL		BIT(10)
 #define SDHCI_PRESET_SDCLK_FREQ_MASK	GENMASK(9, 0)
 
+#define SDHCI_ADMA3_ADDRESS	0x78
+
 #define SDHCI_SLOT_INT_STATUS	0xFC
 
 #define SDHCI_HOST_VERSION	0xFE
-- 
2.25.1




[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux