On 19/10/22 14:06, Victor Shih wrote:
> Add UHS-II specific data structures for commands and defines for
> registers, as described in Part 1 UHS-II Addendum Version 1.01.
>
> UHS-II related definitions are listed below:
> 1. UHS-II card capability: sd_uhs2_caps{}
> 2. UHS-II configuration: sd_uhs2_config{}
> 3. UHS-II Command structure: uhs2_command{}
> 4. UHS-II register I/O address and register field definitions: sd_uhs2.h
>
> Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> Signed-off-by: Jason Lai <jason.lai@xxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
> ---
>
> Updates in V5:
> - Added UHS2 interfaces in mmc_host_ops: host.h
> - Added UHS2 VDD2 power supply in mmc_supply: host.h
> - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
> - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
> - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> ---
> include/linux/mmc/card.h | 42 +++++-
> include/linux/mmc/core.h | 13 ++
> include/linux/mmc/host.h | 70 +++++++++-
> include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 386 insertions(+), 2 deletions(-)
> create mode 100644 include/linux/mmc/sd_uhs2.h
>
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 4a42f31b7bb0..d638a2c689cf 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -190,6 +190,13 @@ struct sd_switch_caps {
> #define SD_MAX_CURRENT_400 (1 << SD_SET_CURRENT_LIMIT_400)
> #define SD_MAX_CURRENT_600 (1 << SD_SET_CURRENT_LIMIT_600)
> #define SD_MAX_CURRENT_800 (1 << SD_SET_CURRENT_LIMIT_800)
> + unsigned int sd4_curr_limit;
> +#define SD4_SET_POWER_LIMIT_0_72W 0
> +#define SD4_SET_POWER_LIMIT_1_44W 1
> +#define SD4_SET_POWER_LIMIT_2_16W 2
> +#define SD4_SET_POWER_LIMIT_2_88W 3
> +#define SD4_SET_POWER_LIMIT_1_80W 4
> +#define SD4_SET_POWER_NO_CHANGE (-1)
> };
>
> struct sd_ext_reg {
> @@ -213,7 +220,35 @@ struct sd_ext_reg {
>
> struct sd_uhs2_config {
> u32 node_id;
> - /* TODO: Extend with more register configs. */
> +
> + u32 dap;
> + u32 gap;
> + u32 n_fcu;
> + u32 maxblk_len;
> + u8 n_lanes;
> + u8 dadr_len;
> + u8 app_type;
> + u8 phy_minor_rev;
> + u8 phy_major_rev;
> + u8 can_hibernate;
> + u8 n_lss_sync;
> + u8 n_lss_dir;
> + u8 link_minor_rev;
> + u8 link_major_rev;
> + u8 dev_type;
> + u8 n_data_gap;
> +
> + u32 n_fcu_set;
> + u32 maxblk_len_set;
> + u8 n_lanes_set;
> + u8 speed_range_set;
> + u8 n_lss_sync_set;
> + u8 n_lss_dir_set;
> + u8 n_data_gap_set;
> + u8 pwrctrl_mode_set;
> + u8 max_retry_set;
> +
> + u8 cfg_complete;
> };
>
> struct sdio_cccr {
> @@ -323,6 +358,9 @@ struct mmc_card {
> struct sd_ext_reg ext_perf; /* SD extension reg for PERF */
>
> struct sd_uhs2_config uhs2_config; /* SD UHS-II config */
> + u8 uhs2_state; /* SD UHS-II states */
> +#define MMC_UHS2_INITIALIZED BIT(1)
> +#define MMC_UHS2_SPEED_B BIT(2)
>
> unsigned int sdio_funcs; /* number of SDIO functions */
> atomic_t sdio_funcs_probed; /* number of probed SDIO funcs */
> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
> #define mmc_card_sdio(c) ((c)->type == MMC_TYPE_SDIO)
> #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
>
> +#define mmc_card_can_poweroff_notify(c) ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> +
> #endif /* LINUX_MMC_CARD_H */
> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> index 6efec0b9820c..2a0581d87706 100644
> --- a/include/linux/mmc/core.h
> +++ b/include/linux/mmc/core.h
> @@ -23,6 +23,14 @@ enum mmc_blk_status {
> MMC_BLK_NEW_REQUEST,
> };
>
> +struct uhs2_command {
> + u16 header;
> + u16 arg;
> + __be32 *payload;
> + u32 payload_len;
> + u32 packet_len;
> +};
> +
> struct mmc_command {
> u32 opcode;
> u32 arg;
> @@ -109,6 +117,11 @@ struct mmc_command {
> unsigned int busy_timeout; /* busy detect timeout in ms */
> struct mmc_data *data; /* data segment associated with cmd */
> struct mmc_request *mrq; /* associated request */
> +
> + struct uhs2_command *uhs2_cmd; /* UHS2 command */
> + u8 *uhs2_resp; /* UHS2 native cmd resp */
> + u8 uhs2_resp_len; /* UHS2 native cmd resp len */
> + u8 uhs2_tmode0_flag; /* UHS2 transfer mode flag */
> };
>
> struct mmc_data {
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 895bcf7f80b7..249a9414ad10 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -16,6 +16,7 @@
> #include <linux/mmc/pm.h>
> #include <linux/dma-direction.h>
> #include <linux/blk-crypto-profile.h>
> +#include <linux/mmc/sd_uhs2.h>
>
> struct mmc_ios {
> unsigned int clock; /* clock rate */
> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
> };
>
> struct sd_uhs2_caps {
> - /* TODO: Add UHS-II capabilities for the host. */
> + u32 dap;
> + u32 gap;
> + u32 group_desc;
> + u32 maxblk_len;
> + u32 n_fcu;
> + u8 n_lanes;
> + u8 addr64;
> + u8 card_type;
> + u8 phy_rev;
> + u8 speed_range;
> + u8 can_hibernate;
> + u8 n_lss_sync;
> + u8 n_lss_dir;
> + u8 link_rev;
> + u8 host_type;
> + u8 n_data_gap;
> +
> + u32 maxblk_len_set;
> + u32 n_fcu_set;
> + u8 n_lanes_set;
> + u8 n_lss_sync_set;
> + u8 n_lss_dir_set;
> + u8 n_data_gap_set;
> + u8 max_retry_set;
> +};
> +
> +struct sd_uhs2_ios {
> + bool is_2L_HD_mode;
> + bool is_APP_CMD;
> + unsigned int power_delay_ms; /* waiting for stable power */
> +};
> +
> +enum sd_uhs2_operation {
> + UHS2_PHY_INIT = 0,
> + UHS2_SET_CONFIG,
> + UHS2_ENABLE_INT,
> + UHS2_DISABLE_INT,
> + UHS2_ENABLE_CLK,
> + UHS2_DISABLE_CLK,
> + UHS2_CHECK_DORMANT,
> + UHS2_SET_SPEED_B,
> + UHS2_POST_ATTACH_SD,
> };
>
> struct mmc_host;
> @@ -231,6 +273,20 @@ struct mmc_host_ops {
>
> /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> int (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> +
> + /* UHS2 interfaces */
> + int (*uhs2_detect_init)(struct mmc_host *host);
Never called?
> + int (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
Never called?
> + int (*uhs2_disable_clk)(struct mmc_host *host);
Never called?
> + int (*uhs2_enable_clk)(struct mmc_host *host);
Never called?
> +
> + /*
> + * The uhs2_control callback is used to execute SD UHS-II specific
> + * operations. It's mandatory to implement for hosts that supports the
> + * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> + * negative errno in case of a failure or zero for success.
> + */
> + int (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
> };
>
> struct mmc_cqe_ops {
> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
>
> struct mmc_supply {
> struct regulator *vmmc; /* Card power supply */
> + struct regulator *vmmc2; /* UHS2 VDD2 power supply */
> struct regulator *vqmmc; /* Optional Vccq supply */
> struct regulator *vqmmc2; /* Optional supply for phy */
> };
> @@ -344,10 +401,12 @@ struct mmc_host {
> u32 ocr_avail_sdio; /* SDIO-specific OCR */
> u32 ocr_avail_sd; /* SD-specific OCR */
> u32 ocr_avail_mmc; /* MMC-specific OCR */
> + u32 ocr_avail_uhs2; /* UHS2-specific OCR */
> struct wakeup_source *ws; /* Enable consume of uevents */
> u32 max_current_330;
> u32 max_current_300;
> u32 max_current_180;
> + u32 max_current_180_vdd2; /* UHS2 vdd2 max curt. */
>
> #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
> #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
> @@ -366,6 +425,7 @@ struct mmc_host {
> #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
> #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
> #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
> +#define MMC_VDD2_165_195 0x00000080 /* UHS2 VDD2 1.65 ~ 1.95 */
>
> u32 caps; /* Host capabilities */
>
> @@ -443,7 +503,12 @@ struct mmc_host {
> #endif
> #define MMC_CAP2_ALT_GPT_TEGRA (1 << 28) /* Host with eMMC that has GPT entry at a non-standard location */
>
> + int flags;
> +#define MMC_UHS2_SUPPORT (1 << 0)
MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
Both have the same value, but MMC_UHS2_SUPPORT is for
host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
Please use the correct flag with the correct variable.
> +#define MMC_UHS2_2L_HD (1 << 2)
MMC_UHS2_2L_HD does not seem to be used. Is it needed?
> +
> struct sd_uhs2_caps uhs2_caps; /* Host UHS-II capabilities */
> + struct sd_uhs2_ios uhs2_ios; /* Host UHS-II capabilities */
>
> int fixed_drv_type; /* fixed driver type for non-removable media */
>
> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
>
> +#define mmc_uhs2_2L_HD_mode(h) ((h)->uhs2_ios.is_2L_HD_mode)
> +#define mmc_uhs2_APP_cmd(h) ((h)->uhs2_ios.is_APP_CMD)
> +
> #endif /* LINUX_MMC_HOST_H */
> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> new file mode 100644
> index 000000000000..8fcf702cf4a5
> --- /dev/null
> +++ b/include/linux/mmc/sd_uhs2.h
> @@ -0,0 +1,263 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Header file for UHS-II packets, Host Controller registers and I/O
> + * accessors.
> + *
> + * Copyright (C) 2014 Intel Corp, All Rights Reserved.
> + */
> +#ifndef LINUX_MMC_UHS2_H
> +#define LINUX_MMC_UHS2_H
> +
> +/* LINK Layer definition */
> +/*
> + * UHS2 Header:
> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> + * bit [3:0] : DID(Destination ID = Node ID of UHS2 card)
> + * bit [6:4] : TYP(Packet Type)
> + * 000b: CCMD(Control command packet)
> + * 001b: DCMD(Data command packet)
> + * 010b: RES(Response packet)
> + * 011b: DATA(Data payload packet)
> + * 111b: MSG(Message packet)
> + * Others: Reserved
> + * bit [7] : NP(Native Packet)
> + * bit [10:8] : TID(Transaction ID)
> + * bit [11] : Reserved
> + * bit [15:12]: SID(Source ID 0: Node ID of Host)
> + *
> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> + */
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> + * bit [3:0] : MSB of IOADR
> + * bit [5:4] : PLEN(Payload Length)
> + * 00b: 0 byte
> + * 01b: 4 bytes
> + * 10b: 8 bytes
> + * 11b: 16 bytes
> + * bit [6] : Reserved
> + * bit [7] : R/W(Read/Write)
> + * 0: Control read command
> + * 1: Control write command
> + * bit [15:8] : LSB of IOADR
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_NATIVE_PACKET_POS 7
> +#define UHS2_NATIVE_PACKET (1 << UHS2_NATIVE_PACKET_POS)
> +
> +#define UHS2_PACKET_TYPE_POS 4
> +#define UHS2_PACKET_TYPE_CCMD (0 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DCMD (1 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DATA (3 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> +
> +#define UHS2_DEST_ID_MASK 0x0F
> +#define UHS2_DEST_ID 0x1
> +
> +#define UHS2_SRC_ID_POS 12
> +#define UHS2_SRC_ID_MASK 0xF000
> +
> +#define UHS2_TRANS_ID_POS 8
> +#define UHS2_TRANS_ID_MASK 0x0700
> +
> +/* UHS2 MSG */
> +#define UHS2_MSG_CTG_POS 5
> +#define UHS2_MSG_CTG_LMSG 0x00
> +#define UHS2_MSG_CTG_INT 0x60
> +#define UHS2_MSG_CTG_AMSG 0x80
> +
> +#define UHS2_MSG_CTG_FCREQ 0x00
> +#define UHS2_MSG_CTG_FCRDY 0x01
> +#define UHS2_MSG_CTG_STAT 0x02
> +
> +#define UHS2_MSG_CODE_POS 8
> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR 0x8
> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR 0x8
> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR 0x1
> +
> +/* TRANS Layer definition */
> +
> +/* Native packets*/
> +#define UHS2_NATIVE_CMD_RW_POS 7
> +#define UHS2_NATIVE_CMD_WRITE (1 << UHS2_NATIVE_CMD_RW_POS)
> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> +
> +#define UHS2_NATIVE_CMD_PLEN_POS 4
> +#define UHS2_NATIVE_CMD_PLEN_4B (1 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_8B (2 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_16B (3 << UHS2_NATIVE_CMD_PLEN_POS)
> +
> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK 0xF00
> +#define UHS2_NATIVE_CCMD_MIOADR_MASK 0x0F
> +
> +#define UHS2_NATIVE_CCMD_LIOADR_POS 8
> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK 0x0FF
> +
> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG BIT(11)
> +#define UHS2_DEV_INIT_PAYLOAD_LEN 1
> +#define UHS2_DEV_INIT_RESP_LEN 6
> +#define UHS2_DEV_ENUM_PAYLOAD_LEN 1
> +#define UHS2_DEV_ENUM_RESP_LEN 8
> +#define UHS2_CFG_WRITE_PAYLOAD_LEN 2
> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN 4
> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN 5
> +#define UHS2_GO_DORMANT_PAYLOAD_LEN 1
> +
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> + * bit [3:0] : Reserved
> + * bit [6:3] : TMODE(Transfer Mode)
> + * bit 3: DAM(Data Access Mode)
> + * bit 4: TLUM(TLEN Unit Mode)
> + * bit 5: LM(Length Mode)
> + * bit 6: DM(Duplex Mode)
> + * bit [7] : R/W(Read/Write)
> + * 0: Control read command
> + * 1: Control write command
> + * bit [15:8] : Reserved
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_DCMD_DM_POS 6
> +#define UHS2_DCMD_2L_HD_MODE (1 << UHS2_DCMD_DM_POS)
> +#define UHS2_DCMD_LM_POS 5
> +#define UHS2_DCMD_LM_TLEN_EXIST (1 << UHS2_DCMD_LM_POS)
> +#define UHS2_DCMD_TLUM_POS 4
> +#define UHS2_DCMD_TLUM_BYTE_MODE (1 << UHS2_DCMD_TLUM_POS)
> +#define UHS2_NATIVE_DCMD_DAM_POS 3
> +#define UHS2_NATIVE_DCMD_DAM_IO (1 << UHS2_NATIVE_DCMD_DAM_POS)
> +
> +/*
> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> + * two types of data be assembled to MSB:
> + * 1. TLEN: Input block size for single read/write and number of blocks
> + * for multiple read/write to calculate TLEN as MSB first per spec.
> + * 2. SD command argument.
> + */
> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> +{
> + u32 ret = 0;
> +
> + ret = ((input & 0xFF) << 24) |
> + (((input >> 8) & 0xFF) << 16) |
> + (((input >> 16) & 0xFF) << 8) |
> + ((input >> 24) & 0xFF);
> + return cpu_to_be32(ret);
> +}
> +
> +#define UHS2_RES_NACK_POS 7
> +#define UHS2_RES_NACK_MASK (0x1 << UHS2_RES_NACK_POS)
> +
> +#define UHS2_RES_ECODE_POS 4
> +#define UHS2_RES_ECODE_MASK 0x7
> +#define UHS2_RES_ECODE_COND 1
> +#define UHS2_RES_ECODE_ARG 2
> +#define UHS2_RES_ECODE_GEN 3
> +
> +/* IOADR of device registers */
> +#define UHS2_IOADR_GENERIC_CAPS 0x00
> +#define UHS2_IOADR_PHY_CAPS 0x02
> +#define UHS2_IOADR_LINK_CAPS 0x04
> +#define UHS2_IOADR_RSV_CAPS 0x06
> +#define UHS2_IOADR_GENERIC_SETTINGS 0x08
> +#define UHS2_IOADR_PHY_SETTINGS 0x0A
> +#define UHS2_IOADR_LINK_SETTINGS 0x0C
> +#define UHS2_IOADR_PRESET 0x40
> +
> +/* SD application packets */
> +#define UHS2_SD_CMD_INDEX_POS 8
> +
> +#define UHS2_SD_CMD_APP_POS 14
> +#define UHS2_SD_CMD_APP (1 << UHS2_SD_CMD_APP_POS)
> +
> +/* UHS-II Device Registers */
> +#define UHS2_DEV_CONFIG_REG 0x000
> +
> +/* General Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_GEN_CAPS (UHS2_DEV_CONFIG_REG + 0x000)
> +#define UHS2_DEV_CONFIG_N_LANES_POS 8
> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> +#define UHS2_DEV_CONFIG_2L_HD_FD 0x1
> +#define UHS2_DEV_CONFIG_2D1U_FD 0x2
> +#define UHS2_DEV_CONFIG_1D2U_FD 0x4
> +#define UHS2_DEV_CONFIG_2D2U_FD 0x8
> +#define UHS2_DEV_CONFIG_DADR_POS 14
> +#define UHS2_DEV_CONFIG_DADR_MASK 0x1
> +#define UHS2_DEV_CONFIG_APP_POS 16
> +#define UHS2_DEV_CONFIG_APP_MASK 0xFF
> +#define UHS2_DEV_CONFIG_APP_SD_MEM 0x1
> +
> +#define UHS2_DEV_CONFIG_GEN_SET (UHS2_DEV_CONFIG_REG + 0x008)
> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS 8
> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD 0x0
> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD 0x2
> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD 0x3
> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD 0x4
> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> +
> +/* PHY Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_PHY_CAPS (UHS2_DEV_CONFIG_REG + 0x002)
> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK 0xF
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS 4
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK 0x3
> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS 15
> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK 0x1
> +#define UHS2_DEV_CONFIG_PHY_CAPS1 (UHS2_DEV_CONFIG_REG + 0x003)
> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK 0xF
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS 4
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK 0xF
> +
> +#define UHS2_DEV_CONFIG_PHY_SET (UHS2_DEV_CONFIG_REG + 0x00A)
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS 6
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A 0x0
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B 0x1
> +
> +/* LINK-TRAN Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS (UHS2_DEV_CONFIG_REG + 0x004)
> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK 0xF
> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS 4
> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK 0x3
> +#define UHS2_DEV_CONFIG_N_FCU_POS 8
> +#define UHS2_DEV_CONFIG_N_FCU_MASK 0xFF
> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS 16
> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK 0x7
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS 20
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK 0xFFF
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1 (UHS2_DEV_CONFIG_REG + 0x005)
> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK 0xFF
> +
> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET (UHS2_DEV_CONFIG_REG + 0x00C)
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN 0x200
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> +
> +/* Preset register */
> +#define UHS2_DEV_CONFIG_PRESET (UHS2_DEV_CONFIG_REG + 0x040)
> +
> +#define UHS2_DEV_INT_REG 0x100
> +
> +#define UHS2_DEV_STATUS_REG 0x180
> +
> +#define UHS2_DEV_CMD_REG 0x200
> +#define UHS2_DEV_CMD_FULL_RESET (UHS2_DEV_CMD_REG + 0x000)
> +#define UHS2_DEV_CMD_GO_DORMANT_STATE (UHS2_DEV_CMD_REG + 0x001)
> +#define UHS2_DEV_CMD_DORMANT_HIBER BIT(7)
> +#define UHS2_DEV_CMD_DEVICE_INIT (UHS2_DEV_CMD_REG + 0x002)
> +#define UHS2_DEV_INIT_COMPLETE_FLAG BIT(11)
> +#define UHS2_DEV_CMD_ENUMERATE (UHS2_DEV_CMD_REG + 0x003)
> +#define UHS2_DEV_CMD_TRANS_ABORT (UHS2_DEV_CMD_REG + 0x004)
> +
> +#define UHS2_RCLK_MAX 52000000
> +#define UHS2_RCLK_MIN 26000000
> +
> +struct sd_uhs2_wait_active_state_data {
> + struct mmc_host *host;
> + struct mmc_command *cmd;
> +};
> +
> +#endif /* LINUX_MMC_UHS2_H */
