On Fri, 21 Oct 2022 at 22:45, Arnd Bergmann <arnd@xxxxxxxxxx> wrote: > > From: Arnd Bergmann <arnd@xxxxxxxx> > > The s3c24xx platform is gone, so this driver can be removed as well. > > Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx> Acked-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx> Kind regards Uffe > --- > MAINTAINERS | 6 - > drivers/mmc/host/Kconfig | 43 - > drivers/mmc/host/Makefile | 1 - > drivers/mmc/host/s3cmci.c | 1777 ---------------------- > drivers/mmc/host/s3cmci.h | 75 - > include/linux/platform_data/mmc-s3cmci.h | 51 - > 6 files changed, 1953 deletions(-) > delete mode 100644 drivers/mmc/host/s3cmci.c > delete mode 100644 drivers/mmc/host/s3cmci.h > delete mode 100644 include/linux/platform_data/mmc-s3cmci.h > > diff --git a/MAINTAINERS b/MAINTAINERS > index 2caf42b0328a..503ebd9800db 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -17920,12 +17920,6 @@ S: Supported > W: http://www.ibm.com/developerworks/linux/linux390/ > F: drivers/s390/scsi/zfcp_* > > -S3C24XX SD/MMC Driver > -M: Ben Dooks <ben-linux@xxxxxxxxx> > -L: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx (moderated for non-subscribers) > -S: Supported > -F: drivers/mmc/host/s3cmci.* > - > SAA6588 RDS RECEIVER DRIVER > M: Hans Verkuil <hverkuil@xxxxxxxxx> > L: linux-media@xxxxxxxxxxxxxxx > diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig > index 79d8ddf1f616..75e8c364243d 100644 > --- a/drivers/mmc/host/Kconfig > +++ b/drivers/mmc/host/Kconfig > @@ -619,49 +619,6 @@ config MMC_SPI > > If unsure, or if your system has no SPI master driver, say N. > > -config MMC_S3C > - tristate "Samsung S3C SD/MMC Card Interface support" > - depends on ARCH_S3C24XX || COMPILE_TEST > - depends on S3C24XX_DMAC || COMPILE_TEST > - help > - This selects a driver for the MCI interface found in > - Samsung's S3C2410, S3C2412, S3C2440, S3C2442 CPUs. > - If you have a board based on one of those and a MMC/SD > - slot, say Y or M here. > - > - If unsure, say N. > - > -config MMC_S3C_HW_SDIO_IRQ > - bool "Hardware support for SDIO IRQ" > - depends on MMC_S3C > - help > - Enable the hardware support for SDIO interrupts instead of using > - the generic polling code. > - > -choice > - prompt "Samsung S3C SD/MMC transfer code" > - depends on MMC_S3C > - > -config MMC_S3C_PIO > - bool "Use PIO transfers only" > - help > - Use PIO to transfer data between memory and the hardware. > - > - PIO is slower than DMA as it requires CPU instructions to > - move the data. This has been the traditional default for > - the S3C MCI driver. > - > -config MMC_S3C_DMA > - bool "Use DMA transfers only" > - help > - Use DMA to transfer data between memory and the hardware. > - > - Currently, the DMA support in this driver seems to not be > - working properly and needs to be debugged before this > - option is useful. > - > -endchoice > - > config MMC_SDRICOH_CS > tristate "MMC/SD driver for Ricoh Bay1Controllers" > depends on PCI && PCMCIA > diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile > index 0baeb0b004f7..885e19e21e75 100644 > --- a/drivers/mmc/host/Makefile > +++ b/drivers/mmc/host/Makefile > @@ -34,7 +34,6 @@ obj-$(CONFIG_MMC_MVSDIO) += mvsdio.o > obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o > obj-$(CONFIG_MMC_SPI) += mmc_spi.o > obj-$(CONFIG_MMC_SPI) += of_mmc_spi.o > -obj-$(CONFIG_MMC_S3C) += s3cmci.o > obj-$(CONFIG_MMC_SDRICOH_CS) += sdricoh_cs.o > obj-$(CONFIG_MMC_TMIO_CORE) += tmio_mmc_core.o > obj-$(CONFIG_MMC_SDHI) += renesas_sdhi_core.o > diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c > deleted file mode 100644 > index 8d5929a32d34..000000000000 > diff --git a/drivers/mmc/host/s3cmci.h b/drivers/mmc/host/s3cmci.h > deleted file mode 100644 > index 8b65d7ad9f97..000000000000 > diff --git a/include/linux/platform_data/mmc-s3cmci.h b/include/linux/platform_data/mmc-s3cmci.h > deleted file mode 100644 > index bacb86db3112..000000000000 > -- > 2.29.2 >
