On 16/12/2021 08:08, fred wrote:
> From: Fred Ai <fred.ai@xxxxxxxxxxxxxx>
>
> Card input timing is margin, need to adjust the hold timing of card input.
>
> Signed-off-by: Fred Ai <fred.ai@xxxxxxxxxxxxxx>
> ---
> Change in V3:
> 1.Select suit DLL phase's output clock as SD interface clock at SDR104/HS200 mode.
> 2.Deselect DLL output phase as SD interface clock before next card initialization.
> ---
> drivers/mmc/host/sdhci-pci-o2micro.c | 56 +++++++++++++++++++++++-----
> 1 file changed, 47 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index f045c1ee4667..f55602609f8c 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -43,11 +43,15 @@
> #define O2_SD_CAP_REG0 0x334
> #define O2_SD_UHS1_CAP_SETTING 0x33C
> #define O2_SD_DELAY_CTRL 0x350
> +#define O2_SD_OUTPUT_CLK_SOURCE_SWITCH 0x354
> #define O2_SD_UHS2_L1_CTRL 0x35C
> #define O2_SD_FUNC_REG3 0x3E0
> #define O2_SD_FUNC_REG4 0x3E4
> #define O2_SD_LED_ENABLE BIT(6)
> #define O2_SD_FREG0_LEDOFF BIT(13)
> +#define O2_SD_SEL_DLL BIT(16)
> +#define O2_SD_FIX_PHASE (BIT(23) | BIT(20))
> +#define O2_SD_PHASE_MASK GENMASK(23, 20)
> #define O2_SD_FREG4_ENABLE_CLK_SET BIT(22)
>
> #define O2_SD_VENDOR_SETTING 0x110
> @@ -301,9 +305,13 @@ static int sdhci_o2_dll_recovery(struct sdhci_host *host)
> static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
> {
> struct sdhci_host *host = mmc_priv(mmc);
> + struct sdhci_pci_slot *slot = sdhci_priv(host);
> + struct sdhci_pci_chip *chip = slot->chip;
> int current_bus_width = 0;
> u32 scratch32 = 0;
> u16 scratch = 0;
> + u8 scratch_8 = 0;
> + u32 reg_val;
>
> /*
> * This handler only implements the eMMC tuning that is specific to
> @@ -322,6 +330,32 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
> scratch |= O2_SD_PWR_FORCE_L0;
> sdhci_writew(host, scratch, O2_SD_MISC_CTRL);
>
> + /* Stop clk */
> + reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> + reg_val &= ~SDHCI_CLOCK_CARD_EN;
> + sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
> +
> + /* UnLock WP */
> + pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch_8);
> + scratch_8 &= 0x7f;
> + pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch_8);
> +
> + /* Set pcr 0x354[16] to choose dll clock, and set the default phase */
> + pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, ®_val);
> + reg_val &= ~(O2_SD_SEL_DLL | O2_SD_PHASE_MASK);
> + reg_val |= (O2_SD_SEL_DLL | O2_SD_FIX_PHASE);
> + pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, reg_val);
> +
> + /* Lock WP */
> + pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch_8);
> + scratch_8 |= 0x80;
> + pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch_8);
> +
> + /* Start clk */
> + reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> + reg_val |= SDHCI_CLOCK_CARD_EN;
> + sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
> +
> /* wait DLL lock, timeout value 5ms */
> if (readx_poll_timeout(sdhci_o2_pll_dll_wdt_control, host,
> scratch32, (scratch32 & O2_DLL_LOCK_STATUS), 1, 5000))
> @@ -533,22 +567,26 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
> if (clock == 0)
> return;
>
> - if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
> - pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> -
> - scratch &= 0x7f;
> - pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
> + /* UnLock WP */
> + pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> + scratch &= 0x7f;
> + pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
>
> + if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
> pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
>
> if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
> o2_pci_set_baseclk(chip, 0x2c280000);
> + }
>
> - pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> + pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &scratch_32);
> + scratch_32 &= ~(O2_SD_SEL_DLL | O2_SD_PHASE_MASK);
> + pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, scratch_32);
>
> - scratch |= 0x80;
> - pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
> - }
> + /* Lock WP */
Also please nudge this indent into line.
> + pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> + scratch |= 0x80;
> + pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
>
> clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
> sdhci_o2_enable_clk(host, clk);
>
