On Tue, 03 Aug 2021 at 12:23, Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
>
> On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@xxxxxxxxx> wrote:
> >
> > Summary
> > =======
> > In these patches we focus on uhs2 side to address Ulf's suggestion which
> > was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
> >
> >
> > I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> > Ulf's expection.
> >
> > Please review this series (particularly Patch 29/29).
>
> I think you have misunderstood the intent with the series that I
> posted [1] a while ago. The idea was to add the foundation of what
> should be needed in the mmc core to support UHS-II cards. Note, it's
> only the foundation, not the complete code.
>
> In other words, I think you should base the next version of $subject
> series *on top* of my series [1], rather than the opposite.
>
Actually, I understand your intention is to implement functions which
can be applied to control all UHS-II cards.
However, why do I choose to base it on “[RFC,v3.1,00/27] Add support
UHS-II for GL9755”?
Because it contains a complete UHS-II interface(both host & card side)
and UHS-II card can work normally.
The functionality of uhs2.c in the previous version of $subject almost
equal to sd_uhs2.c in your series [1].
The only difference is that UHS-II card initialization flow had been
modulated according to different phases(detect / phy_init /
legacy_init…).
Hence, I decided to apply your architecture of sd_uhs2.c to uhs2.c and
rename uhs2.c to sd_uhs2.c.
All patches are briefed below:
1. Patch #1 to patch #26 are used to create a UHS-II interface, both
in host side and sd card side.
- patch#1: add UHS-II support in public headers. (include/linux/mmc).
- patch#2: add UHS-II relative features in mmc_power_up() /
mmc_power_off() / mmc_regulator_get_supply().
- patch#3: skip set_chip_select().
- patch#4: flow of “interface selection and initialization” was a
bit modified for UHS-II card.
- patch#5: skip TMODE(field of UHS-II command packet) setup in some cases.
- patch#6 - #7: generate UHS-II SD command packet.
- patch#8: add a kernel configuration for enabling UHS-II support.
- patch#9: add UHS-II related definitions in sdhci.h and sdhci-uhs2.h.
- patch#10: add sdhci-uhs2.c as a module for UHS-II support.
- patch#11: dump UHS-II registers
- patch#12 - #26: add UHS-II host setting / control / attach,
card detect / attach.
2. Patch #27: drivers/mmc/host/sdhci-pci-gli.c contains
vendor(Genesyslogic) specific operations which are related to hardware
control.
3. Patch #28: remove redundant code.
4. Patch #29: move code from uhs2.c to sd_uhs2.c and place them to
proper functions.
> Moreover, next time, please try to better describe in each changelog
> and in a cover letter what you have changed and why, as it helps me to
> review.
Okay.
So what is the next you suggest to do after my explanation?
1. Update cover letter & change note in current version of $subject.
2. Submit a new version on top of your series [1].
For example: Series “Add Support UHS-II for GL9755“
patch #1~#4 are your original series[1] and patch #33 is to apply
your patch to support UHS-II cards. Below is the patch list:
[0/33] mmc: core: Add Support UHS-II for GL9755
[1/33] mmc: core: Cleanup printing of speed mode at card insertion
[2/33] mmc: core: Prepare to support SD UHS-II cards
[3/33] mmc: core: Announce successful insertion of an SD UHS-II card
[4/33] mmc: core: Extend support for mmc regulators with a vqmmc2
[5/33] mmc: add UHS-II related definitions in public headers
[6/33] mmc: core: UHS-II support, modify power-up sequence
……
[33/33] mmc: core: Apply Ulf's patch for supporting UHS-II car
Kind regards,
Jason Lai
> Kind regards
> Uffe
>
> [1]
> https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
>
> >
> > Thanks.
> > -Jason Lai
> >
> > ------ original cover letter from v3 ------
> > This is an interim snapshot of our next version, v4, for enabling
> > UHS-II on MMC/SD.
> >
> > It is focused on 'sdhci' side to address Adrian's comments regarding
> > "modularising" sdhci-uhs2.c.
> > The whole aim of this version is to get early feedback from Adrian (and
> > others) on this issue. Without any consensus about the code structure,
> > it would make little sense to go further ahead on sdhci side.
> > (Actually, Adrian has made no comments other than "modularising" so far.)
> >
> > I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> > set to meet what I believe Adrian expects; no UHS-II related code in
> > Legacy (UHS-I) code or sdhci.c.
> >
> > Nevertheless, almost of all changes I made are trivial and straightforward
> > in this direction, and I believe that there is no logic changed since v3
> > except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> > command sequences in addition to UHS-II errors. So I added extra handlings.
> >
> > I admit that there is plenty of room for improvements (for example,
> > handling host->flags), but again the focal point here is how sdhci-uhs2.c
> > should be built as a module.
> >
> > Please review this series (particularly Patch#8-#26 and #27) from this
> > viewpoint in the first place.
> > (Ben is working on 'host' side but there is no change on 'host' side
> > in this submission except a minor tweak.)
> >
> > Thanks,
> > -Takahiro Akashi
> >
> > ------ original cover letter from v3 ------
> > Summary
> > =======
> > These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
> >
> > About UHS-II, roughly deal with the following three parts:
> > 1) A UHS-II detection and initialization:
> > - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
> > [2]).
> > - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> > - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
> > 3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
> > Setup Sequence.
> >
> > 2) Send Legacy SD command through SD-TRAN
> > - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
> > compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
> > Types and Format Overview[3]).
> > - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
> > CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
> >
> > 3) UHS-II Interrupt
> > - Except for UHS-II error interrupts, most interrupts share the original
> > interrupt registers.
> >
> > Patch structure
> > ===============
> > patch#1-#7: for core
> > patch#8-#17: for sdhci
> > patch#18-#21: for GL9755
> >
> > Tests
> > =====
> > Ran 'dd' command to evaluate the performance:
> > (SanDisk UHS-II card on GL9755 controller)
> > Read Write
> > UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> > UHS-II enabled : 206MB/s 80MB/s
> >
> > TODO
> > ====
> > - replace some define with BIT macro
> >
> > Reference
> > =========
> > [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> > [2] SD Host Controller Simplified Specification 4.20
> > [3] UHS-II Simplified Addendum 1.02
> >
> > Changes in v3 (Jul. 10, 2020)
> > * rebased to v5.8-rc4
> > * add copyright notice
> > * reorganize the patch set and split some commits into smaller ones
> > * separate uhs-2 headers from others
> > * correct wrong spellings
> > * fix most of checkpatch warnings/errors
> > * remove all k[cz]alloc() from the code
> > * guard sdhci-uhs2 specific code with
> > 'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> > * make sdhci-uhs2.c as a module
> > * trivial changes, including
> > - rename back sdhci-core.c to sdhci.c
> > - allow vendor code to disable uhs2 if v4_mode == 0
> > in __sdhci_add_host()
> > - merge uhs2_power_up() into mmc_power_up()
> > - remove flag_uhs2 from mmc_attach_sd()
> > - add function descriptions to EXPORT'ed functions
> > - other minor code optimization
> >
> > Changes in v2 (Jan. 9, 2020)
> > * rebased to v5.5-rc5
> >
> > AKASHI Takahiro (23):
> > mmc: core: UHS-II support, modify power-up sequence
> > mmc: core: UHS-II support, skip set_chip_select()
> > mmc: core: UHS-II support, skip TMODE setup in some cases
> > mmc: core: UHS-II support, generate UHS-II SD command packet
> > mmc: core: UHS-II support, set APP_CMD bit if necessary
> > mmc: sdhci: add a kernel configuration for enabling UHS-II support
> > mmc: sdhci: add UHS-II related definitions in headers
> > mmc: sdhci: add UHS-II module
> > mmc: sdhci-uhs2: dump UHS-II registers
> > mmc: sdhci-uhs2: add reset function
> > mmc: sdhci-uhs2: add set_power() to support vdd2
> > mmc: sdhci-uhs2: skip signal_voltage_switch()
> > mmc: sdhci-uhs2: add set_timeout()
> > mmc: sdhci-uhs2: add set_ios()
> > mmc: sdhci-uhs2: add detect_init() to detect the interface
> > mmc: sdhci-uhs2: add clock operations
> > mmc: sdhci-uhs2: add set_reg() to initialise the interface
> > mmc: sdhci-uhs2: add request() and others
> > mmc: sdhci-uhs2: add irq() and others
> > mmc: sdhci-uhs2: add add_host() and others to set up the driver
> > mmc: core: add post-mmc_attach_sd hook
> > mmc: sdhci-pci: add UHS-II support framework
> > mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
> >
> > Ben Chuang (4):
> > mmc: add UHS-II related definitions in public headers
> > mmc: core: UHS-II support, try to select UHS-II interface
> > mmc: sdhci-uhs2: add pre-detect_init hook
> > mmc: sdhci-uhs2: add post-mmc_attach_sd hook
> >
> > drivers/mmc/core/Makefile | 2 +-
> > drivers/mmc/core/block.c | 7 +-
> > drivers/mmc/core/bus.c | 5 +-
> > drivers/mmc/core/core.c | 118 +-
> > drivers/mmc/core/regulator.c | 14 +
> > drivers/mmc/core/sd.c | 32 +
> > drivers/mmc/core/sd_ops.c | 12 +
> > drivers/mmc/core/uhs2.c | 883 +++++++++++++++
> > drivers/mmc/core/uhs2.h | 21 +
> > drivers/mmc/host/Kconfig | 10 +
> > drivers/mmc/host/Makefile | 1 +
> > drivers/mmc/host/sdhci-pci-core.c | 16 +-
> > drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
> > drivers/mmc/host/sdhci-pci.h | 3 +
> > drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci-uhs2.h | 224 ++++
> > drivers/mmc/host/sdhci.c | 333 +++---
> > drivers/mmc/host/sdhci.h | 117 +-
> > include/linux/mmc/card.h | 1 +
> > include/linux/mmc/core.h | 6 +
> > include/linux/mmc/host.h | 31 +
> > include/linux/mmc/uhs2.h | 268 +++++
> > 22 files changed, 3961 insertions(+), 158 deletions(-)
> > create mode 100644 drivers/mmc/core/uhs2.c
> > create mode 100644 drivers/mmc/core/uhs2.h
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.c
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> > create mode 100644 include/linux/mmc/uhs2.h
Ulf Hansson <ulf.hansson@xxxxxxxxxx> 於 2021年8月3日 週二 上午12:23寫道：
>
> On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@xxxxxxxxx> wrote:
> >
> > Summary
> > =======
> > In these patches we focus on uhs2 side to address Ulf's suggestion which
> > was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
> >
> >
> > I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> > Ulf's expection.
> >
> > Please review this series (particularly Patch 29/29).
>
> I think you have misunderstood the intent with the series that I
> posted [1] a while ago. The idea was to add the foundation of what
> should be needed in the mmc core to support UHS-II cards. Note, it's
> only the foundation, not the complete code.
>
> In other words, I think you should base the next version of $subject
> series *on top* of my series [1], rather than the opposite.
>
> Moreover, next time, please try to better describe in each changelog
> and in a cover letter what you have changed and why, as it helps me to
> review.
>
> Kind regards
> Uffe
>
> [1]
> https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
>
> >
> > Thanks.
> > -Jason Lai
> >
> > ------ original cover letter from v3 ------
> > This is an interim snapshot of our next version, v4, for enabling
> > UHS-II on MMC/SD.
> >
> > It is focused on 'sdhci' side to address Adrian's comments regarding
> > "modularising" sdhci-uhs2.c.
> > The whole aim of this version is to get early feedback from Adrian (and
> > others) on this issue. Without any consensus about the code structure,
> > it would make little sense to go further ahead on sdhci side.
> > (Actually, Adrian has made no comments other than "modularising" so far.)
> >
> > I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> > set to meet what I believe Adrian expects; no UHS-II related code in
> > Legacy (UHS-I) code or sdhci.c.
> >
> > Nevertheless, almost of all changes I made are trivial and straightforward
> > in this direction, and I believe that there is no logic changed since v3
> > except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> > command sequences in addition to UHS-II errors. So I added extra handlings.
> >
> > I admit that there is plenty of room for improvements (for example,
> > handling host->flags), but again the focal point here is how sdhci-uhs2.c
> > should be built as a module.
> >
> > Please review this series (particularly Patch#8-#26 and #27) from this
> > viewpoint in the first place.
> > (Ben is working on 'host' side but there is no change on 'host' side
> > in this submission except a minor tweak.)
> >
> > Thanks,
> > -Takahiro Akashi
> >
> > ------ original cover letter from v3 ------
> > Summary
> > =======
> > These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
> >
> > About UHS-II, roughly deal with the following three parts:
> > 1) A UHS-II detection and initialization:
> > - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
> > [2]).
> > - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> > - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
> > 3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
> > Setup Sequence.
> >
> > 2) Send Legacy SD command through SD-TRAN
> > - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
> > compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
> > Types and Format Overview[3]).
> > - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
> > CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
> >
> > 3) UHS-II Interrupt
> > - Except for UHS-II error interrupts, most interrupts share the original
> > interrupt registers.
> >
> > Patch structure
> > ===============
> > patch#1-#7: for core
> > patch#8-#17: for sdhci
> > patch#18-#21: for GL9755
> >
> > Tests
> > =====
> > Ran 'dd' command to evaluate the performance:
> > (SanDisk UHS-II card on GL9755 controller)
> > Read Write
> > UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> > UHS-II enabled : 206MB/s 80MB/s
> >
> > TODO
> > ====
> > - replace some define with BIT macro
> >
> > Reference
> > =========
> > [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> > [2] SD Host Controller Simplified Specification 4.20
> > [3] UHS-II Simplified Addendum 1.02
> >
> > Changes in v3 (Jul. 10, 2020)
> > * rebased to v5.8-rc4
> > * add copyright notice
> > * reorganize the patch set and split some commits into smaller ones
> > * separate uhs-2 headers from others
> > * correct wrong spellings
> > * fix most of checkpatch warnings/errors
> > * remove all k[cz]alloc() from the code
> > * guard sdhci-uhs2 specific code with
> > 'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> > * make sdhci-uhs2.c as a module
> > * trivial changes, including
> > - rename back sdhci-core.c to sdhci.c
> > - allow vendor code to disable uhs2 if v4_mode == 0
> > in __sdhci_add_host()
> > - merge uhs2_power_up() into mmc_power_up()
> > - remove flag_uhs2 from mmc_attach_sd()
> > - add function descriptions to EXPORT'ed functions
> > - other minor code optimization
> >
> > Changes in v2 (Jan. 9, 2020)
> > * rebased to v5.5-rc5
> >
> > AKASHI Takahiro (23):
> > mmc: core: UHS-II support, modify power-up sequence
> > mmc: core: UHS-II support, skip set_chip_select()
> > mmc: core: UHS-II support, skip TMODE setup in some cases
> > mmc: core: UHS-II support, generate UHS-II SD command packet
> > mmc: core: UHS-II support, set APP_CMD bit if necessary
> > mmc: sdhci: add a kernel configuration for enabling UHS-II support
> > mmc: sdhci: add UHS-II related definitions in headers
> > mmc: sdhci: add UHS-II module
> > mmc: sdhci-uhs2: dump UHS-II registers
> > mmc: sdhci-uhs2: add reset function
> > mmc: sdhci-uhs2: add set_power() to support vdd2
> > mmc: sdhci-uhs2: skip signal_voltage_switch()
> > mmc: sdhci-uhs2: add set_timeout()
> > mmc: sdhci-uhs2: add set_ios()
> > mmc: sdhci-uhs2: add detect_init() to detect the interface
> > mmc: sdhci-uhs2: add clock operations
> > mmc: sdhci-uhs2: add set_reg() to initialise the interface
> > mmc: sdhci-uhs2: add request() and others
> > mmc: sdhci-uhs2: add irq() and others
> > mmc: sdhci-uhs2: add add_host() and others to set up the driver
> > mmc: core: add post-mmc_attach_sd hook
> > mmc: sdhci-pci: add UHS-II support framework
> > mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
> >
> > Ben Chuang (4):
> > mmc: add UHS-II related definitions in public headers
> > mmc: core: UHS-II support, try to select UHS-II interface
> > mmc: sdhci-uhs2: add pre-detect_init hook
> > mmc: sdhci-uhs2: add post-mmc_attach_sd hook
> >
> > drivers/mmc/core/Makefile | 2 +-
> > drivers/mmc/core/block.c | 7 +-
> > drivers/mmc/core/bus.c | 5 +-
> > drivers/mmc/core/core.c | 118 +-
> > drivers/mmc/core/regulator.c | 14 +
> > drivers/mmc/core/sd.c | 32 +
> > drivers/mmc/core/sd_ops.c | 12 +
> > drivers/mmc/core/uhs2.c | 883 +++++++++++++++
> > drivers/mmc/core/uhs2.h | 21 +
> > drivers/mmc/host/Kconfig | 10 +
> > drivers/mmc/host/Makefile | 1 +
> > drivers/mmc/host/sdhci-pci-core.c | 16 +-
> > drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
> > drivers/mmc/host/sdhci-pci.h | 3 +
> > drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci-uhs2.h | 224 ++++
> > drivers/mmc/host/sdhci.c | 333 +++---
> > drivers/mmc/host/sdhci.h | 117 +-
> > include/linux/mmc/card.h | 1 +
> > include/linux/mmc/core.h | 6 +
> > include/linux/mmc/host.h | 31 +
> > include/linux/mmc/uhs2.h | 268 +++++
> > 22 files changed, 3961 insertions(+), 158 deletions(-)
> > create mode 100644 drivers/mmc/core/uhs2.c
> > create mode 100644 drivers/mmc/core/uhs2.h
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.c
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> > create mode 100644 include/linux/mmc/uhs2.h
