Whenever SDHC run at clock rate 50MHZ or below, the hardware data timeout value will be 21.47secs, which is approx. 22secs and we have a current software timeout value as 10secs. We have to set software timeout value more than the hardware data timeout value to avioid seeing the below register dumps. [ 332.953670] mmc2: Timeout waiting for hardware interrupt. [ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00007202 [ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001 [ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000027 [ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl: 0x0000001f [ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b [ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 [ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x0000808f [ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr: 0x00000000 [ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x00000000 [ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 [ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000 [ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000ffffff218 [ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP ----------- [ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x6000642c | DLL cfg2: 0x0020a000 [ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00000000 | DDR cfg: 0x80040873 [ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 : 0xf88218a8 Vndr func3: 0x02626040 [ 333.102371] mmc2: sdhci: ============================================ So, set software timeout value more than hardware timeout value. Signed-off-by: Shaik Sajida Bhanu <sbhanu@xxxxxxxxxxxxxx> --- drivers/mmc/host/sdhci.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index bf238ad..1386f7d 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -1670,7 +1670,14 @@ static bool sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd) else if (!cmd->data && cmd->busy_timeout > 9000) timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; else - timeout += 10 * HZ; + /* + * In some of the conditions hardware data timeout value could be + * approx 21.5 seconds and driver is setting software data timeout + * value less than the hardware data timeout value and software data + * timeout value should be more than the hardware data timeout value. + * So, set software data timeout value more than 21.5 sec i.e. 22sec. + */ + timeout += 22 * HZ; sdhci_mod_timer(host, cmd->mrq, timeout); if (host->use_external_dma) -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
