Re: [PATCH V2] arm64: dts: qcom: sc7280: Add nodes for eMMC and SD card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 3/23/2021 9:41 PM, Doug Anderson wrote:
Hi,

On Sat, Mar 20, 2021 at 11:18 AM Shaik Sajida Bhanu
<sbhanu@xxxxxxxxxxxxxx> wrote:
Add nodes for eMMC and SD card on sc7280.

Signed-off-by: Shaik Sajida Bhanu <sbhanu@xxxxxxxxxxxxxx>

---
This change is depends on the below patch series:
https://lore.kernel.org/patchwork/project/lkml/list/?series=488871
https://lore.kernel.org/patchwork/project/lkml/list/?series=489530
https://lore.kernel.org/patchwork/project/lkml/list/?series=488429

Changes since V1:
         - Moved SDHC nodes as suggested by Bjorn Andersson.
         - Dropped "pinconf-" prefix as suggested by Bjorn Andersson.
         - Removed extra newlines as suggested by Konrad Dybcio.
         - Changed sd-cd pin to bias-pull-up in sdc2_off as suggested by
           Veerabhadrarao Badiganti.
         - Added bandwidth votes for eMMC and SD card.
---
  arch/arm64/boot/dts/qcom/sc7280-idp.dts |  25 ++++
  arch/arm64/boot/dts/qcom/sc7280.dtsi    | 213 ++++++++++++++++++++++++++++++++
  2 files changed, 238 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 54d2cb3..4105263 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -8,6 +8,7 @@
  /dts-v1/;

  #include "sc7280.dtsi"
+#include <dt-bindings/gpio/gpio.h>

  / {
         model = "Qualcomm Technologies, Inc. sc7280 IDP platform";
@@ -242,6 +243,30 @@
         status = "okay";
  };

+&sdhc_1 {
+       status = "okay";
When I apply your patch I find that your sort order is wrong. "s"
comes before "u" and after "q" in the alphabet so "sdhc_1" and
"sdhc_2" should sort _after "qupv3_id_0" and before "uart5"


+       pinctrl-names = "default", "sleep";
+       pinctrl-0 = <&sdc1_on>;
+       pinctrl-1 = <&sdc1_off>;
+
+       vmmc-supply = <&vreg_l7b_2p9>;
+       vqmmc-supply = <&vreg_l19b_1p8>;
+};
+
+&sdhc_2 {
+       status = "okay";
+
+       pinctrl-names = "default","sleep";
+       pinctrl-0 = <&sdc2_on>;
+       pinctrl-1 = <&sdc2_off>;
+
+       vmmc-supply = <&vreg_l9c_2p9>;
+       vqmmc-supply = <&vreg_l6c_2p9>;
+
+       cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
Where is the pinctrl for the card detect?  Oh, I see it's in
"sdc2_on". Probably would be good to break it out since this is
board-specific. See below.


+};
+
  /* PINCTRL - additions to nodes defined in sc7280.dtsi */

  &qup_uart5_default {
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 8f6b569..69eb064 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -20,6 +20,11 @@

         chosen { };

+       aliases {
+               mmc1 = &sdhc_1;
+               mmc2 = &sdhc_2;
+       };
+
         clocks {
                 xo_board: xo-board {
                         compatible = "fixed-clock";
@@ -305,6 +310,64 @@
                         #power-domain-cells = <1>;
                 };

+               sdhc_1: sdhci@7c4000 {
+                       compatible = "qcom,sdhci-msm-v5";
Please make the compatible:
   compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5";

...and add to the bindings. It should be a trivial bindings patch so
not too much trouble.

NOTE: even though the "qcom,sc7280-sdhci" should be in the bindings
and here you _shouldn't_ be adding any code for it. Just let the
fallback compatible string ("qcom,sdhci-msm-v5") do its magic. Adding
the sc7280 specific version is more of a "just in case we need it
later" type thing.


+                       reg = <0 0x7c4000 0 0x1000>,
+                                       <0 0x7c5000 0 0x1000>;
+                       reg-names = "hc", "cqhci";
+
+                       iommus = <&apps_smmu 0xC0 0x0>;
+                       interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>,
+                                       <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>;
+                       interrupt-names = "hc_irq", "pwr_irq";
+
+                       clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+                                       <&gcc GCC_SDCC1_AHB_CLK>,
+                                       <&rpmhcc RPMH_CXO_CLK>;
+                       clock-names = "core", "iface", "xo";
I'm curious: why is the "xo" clock needed here but not for sc7180?
Actually its needed even for sc7180. We are making use of this clock in msm_init_cm_dll() The default PoR value is also same as calculated value for HS200/HS400/SDR104 modes.
But just not to rely on default register values we need this entry.


+                       interconnects = <&aggre1_noc MASTER_SDCC_1 0 &mc_virt SLAVE_EBI1 0>,
+                                       <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_1 0>;
+                       interconnect-names = "sdhc-ddr","cpu-sdhc";
+                       power-domains = <&rpmhpd SC7280_CX>;
+                       operating-points-v2 = <&sdhc1_opp_table>;
+
+                       bus-width = <8>;
+                       non-removable;
This was actually a problem on sc7180 too, but you probably don't want
"non-removable" in the SoC file. Board files really should be adding
this. Though the SoC might be designed with the idea that this would
be used for a non-removable eMMC card I don't know why it wouldn't be
possible for someone to hook this up to an external slot and use a
GPIO somewhere as a card detect.


+                       supports-cqe;
+                       no-sd;
+                       no-sdio;
Does the port really not support SD / SDIO, or are you adding these
two properties just because on your reference board it's not hooked up
to SD/SDIO? What exactly makes it impossible to use SD/SDIO on this
port?

By having this, we can optimize emmc device scan time.
Driver wont issue SDIO & SDcards specific commands while
scanning the device.Its little optimization.
I think board specific dt is right place.


+                       max-frequency = <192000000>;
Why do you need to specify this?


+                       qcom,dll-config = <0x0007642c>;
+                       qcom,ddr-config = <0x80040868>;
These magic hex values really have no place being in dts which should
have things expressed at a higher level. ...but I guess that ship has
sailed and this is in the bindings so I guess we're stuck with them,
so I guess they're fine.


+                       mmc-ddr-1_8v;
+                       mmc-hs200-1_8v;
+                       mmc-hs400-1_8v;
+                       mmc-hs400-enhanced-strobe;
+
+                       status = "disabled";
+
+                       sdhc1_opp_table: sdhc1-opp-table {
+                               compatible = "operating-points-v2";
+
+                               opp-100000000 {
+                                       opp-hz = /bits/ 64 <100000000>;
+                                       required-opps = <&rpmhpd_opp_low_svs>;
+                                       opp-peak-kBps = <1200000 76000>;
+                                       opp-avg-kBps = <1200000 50000>;
Why are the kBps numbers so vastly different than the ones on sc7180
for the same OPP point. That implies:

a) sc7180 is wrong.

b) This patch is wrong.

c) The numbers are essentially random and don't really matter.

Can you identify which of a), b), or c) is correct, or propose an
alternate explanation of the difference?


+                               };
+
+                               opp-384000000 {
+                                       opp-hz = /bits/ 64 <384000000>;
+                                       required-opps = <&rpmhpd_opp_nom>;
+                                       opp-peak-kBps = <5400000 1600000>;
+                                       opp-avg-kBps = <6000000 300000>;
These opp numbers are also quite different than sc7180


+                               };
+                       };
+               };
+
                 qupv3_id_0: geniqup@9c0000 {
                         compatible = "qcom,geni-se-qup";
                         reg = <0 0x009c0000 0 0x2000>;
@@ -328,6 +391,54 @@
                         };
                 };

+               sdhc_2: sdhci@8804000 {
+                       compatible = "qcom,sdhci-msm-v5";
+                       reg = <0 0x08804000 0 0x1000>;
+
+                       iommus = <&apps_smmu 0x100 0x0>;
+                       interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+                                       <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+                       interrupt-names = "hc_irq", "pwr_irq";
+
+                       clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+                                       <&gcc GCC_SDCC2_AHB_CLK>,
+                                       <&rpmhcc RPMH_CXO_CLK>;
+                       clock-names = "core", "iface", "xo";
+                       interconnects = <&aggre1_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
+                                       <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_2 0>;
+                       interconnect-names = "sdhc-ddr","cpu-sdhc";
+                       power-domains = <&rpmhpd SC7280_CX>;
+                       operating-points-v2 = <&sdhc2_opp_table>;
+
+                       bus-width = <4>;
+
+                       no-mmc;
+                       no-sdio;
Similar question to above: why exactly would mmc not work? Are you
saying that if someone hooked this up to a full sized SD card slot and
placed an MMC card into the slot that it wouldn't work? Similar
question about SDIO. If someone placed an external SDIO card into your
slot, would it not work?

As mentioned above, its just to optimize SDcard scan time a little.
+                       max-frequency = <202000000>;
Not needed?

+
+                       qcom,dll-config = <0x0007642c>;
+
+                       status = "disabled";
+
+                       sdhc2_opp_table: sdhc2-opp-table {
+                                       compatible = "operating-points-v2";
+
+                                       opp-100000000 {
+                                               opp-hz =/bits/ 64 <100000000>;
+                                               required-opps = <&rpmhpd_opp_low_svs>;
+                                               opp-peak-kBps = <1200000 76000>;
+                                               opp-avg-kBps = <1200000 50000>;
+                                       };
+                                       opp-202000000 {
Blank line between the OPPs?

+                                               opp-hz = /bits/ 64 <202000000>;
+                                               required-opps = <&rpmhpd_opp_nom>;
+                                               opp-peak-kBps = <3500000 1200000>;
+                                               opp-avg-kBps = <5000000 100000>;
+                                       };
Similar questions about why the OPPs are so vastly different from sc7180.

+                               };
+               };
+
                 pdc: interrupt-controller@b220000 {
                         compatible = "qcom,sc7280-pdc", "qcom,pdc";
                         reg = <0 0x0b220000 0 0x30000>;
@@ -374,6 +485,108 @@
                                 pins = "gpio46", "gpio47";
                                 function = "qup13";
                         };
+
+                       sdc1_on: sdc1-on {
+                               clk {
+                                       pins = "sdc1_clk";
+                                       bias-disable;
+                                       drive-strength = <16>;
+                               };
+
+                               cmd {
+                                       pins = "sdc1_cmd";
+                                       bias-pull-up;
+                                       drive-strength = <10>;
+                               };
+
+                               data {
+                                       pins = "sdc1_data";
+                                       bias-pull-up;
+                                       drive-strength = <10>;
+                               };
+
+                               rclk {
+                                       pins = "sdc1_rclk";
+                                       bias-pull-down;
+                               };
* generally "bias" doesn't belong in the SoC file but instead should
be in the board file. Some boards might have external pulls (even if
the internal ones would work fine, hardware designers do weird things)
and thus might need to disable the internal ones (double pulls are not
great).

* generally drive-strength doesn't belong in the SoC file but should
be in the board file. Different boards with different layouts might
need different drive strengths, right?

If you remove those two things, I guess there's not actually much left
in the SoC dtsi file so I guess move these all to the board file? That
seems to be what we ended up with in "qrb5165-rb5.dts" / "sm8250.dtsi"
which is an example of a board using the new style of pinctrl for
devicetree.


+                       };
+
+                       sdc1_off: sdc1-off {
+                               clk {
+                                       pins = "sdc1_clk";
+                                       bias-disable;
+                                       drive-strength = <2>;
+                               };
+
+                               cmd {
+                                       pins = "sdc1_cmd";
+                                       bias-pull-up;
+                                       drive-strength = <2>;
+                               };
+
+                               data {
+                                       pins = "sdc1_data";
+                                       bias-pull-up;
+                                       drive-strength = <2>;
+                               };
+
+                               rclk {
+                                       pins = "sdc1_rclk";
+                                       bias-pull-down;
+                               };
+                       };
No need for a sleep state for the rclk since it's the same as the
active state, right? NOTE: one way to handle this would be to define
one node per pingroup and thus do something like:

pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_clk>, <&sdc1_cmd>, <&sdc1_data>, <&sdc1_rclk>;
pinctrl-1 = <&sdc1_clk_sleep>, <&sdc1_cmd_sleep>, <&sdc1_data_sleep>,
<&sdc1_rclk>;

I do wish we could avoid having to duplicate the "bias" in every board
file. Hrm, I wonder if this could be made simpler by actually putting
the "sleep" states in the sc7180.dtsi file (not the board file) and
using "bias-bus-hold" to avoid it being board specific?

Thus (assuming it works), the total summary would be:

1. Board dts file fully defines "sdc1_clk", "sdc1_cmd", "sdc1_data",
"sdc1_rclk", specifying whatever bias and drive strength needed for
the board.

2. SoC dtsi fully defines "sdc1_clk_sleep", "sdc1_cmd_sleep",
"sdc1_data_sleep", "sdc1_rclk_sleep", specifying drive-strength of 2
(for outputs) and "bias-bus-hold" which is OK for all board.


+
+                       sdc2_on: sdc2-on {
+                               clk {
+                                       pins = "sdc2_clk";
+                                       bias-disable;
+                                       drive-strength = <16>;
+                               };
+
+                               cmd {
+                                       pins = "sdc2_cmd";
+                                       bias-pull-up;
+                                       drive-strength = <10>;
+                               };
+
+                               data {
+                                       pins = "sdc2_data";
+                                       bias-pull-up;
+                                       drive-strength = <10>;
+                               };
+
+                               sd-cd {
+                                       pins = "gpio91";
NOTE: even if we find some reason to keep some of the pinctrl in the
SoC dtsi file, the card detect almost certainly needs to move _fully_
to the board dts file. Different boards could use a different card
detect pin.

+                                       bias-pull-up;
+                                       drive-strength = <2>;
Drive strength isn't needed for input pins. Please remove.

+                               };
+                       };
+
+                       sdc2_off: sdc2-off {
+                               clk {
+                                       pins = "sdc2_clk";
+                                       bias-disable;
+                                       drive-strength = <2>;
+                               };
+
+                               cmd {
+                                       pins = "sdc2_cmd";
+                                       bias-pull-up;
+                                       drive-strength = <2>;
+                               };
+
+                               data {
+                                       pins = "sdc2_data";
+                                       bias-pull-up;
+                                       drive-strength = <2>;
+                               };
+
+                               sd-cd {
+                                       pins = "gpio91";
+                                       bias-pull-up;
+                                       drive-strength = <2>;
+                               };
There's definitely no need for a separate sleep state for the CD line.


-Doug



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux