Re: [PATCH] mmc: Try power cycling card if command request times out

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 1/03/21 10:50 am, Ulf Hansson wrote:
> + Adrian
> 
> On Tue, 16 Feb 2021 at 23:43, Mårten Lindahl <marten.lindahl@xxxxxxxx> wrote:
>>
>> Sometimes SD cards that has been run for a long time enters a state
>> where it cannot by itself be recovered, but needs a power cycle to be
>> operational again. Card status analysis has indicated that the card can
>> end up in a state where all external commands are ignored by the card
>> since it is halted by data timeouts.
>>
>> If the card has been heavily used for a long time it can be weared out,
>> and should typically be replaced. But on some tests, it shows that the
>> card can still be functional after a power cycle, but as it requires an
>> operator to do it, the card can remain in a non-operational state for a
>> long time until the problem has been observed by the operator.
>>
>> This patch adds function to power cycle the card in case it does not
>> respond to a command, and then resend the command if the power cycle
>> was successful. This procedure will be tested 1 time before giving up,
>> and resuming host operation as normal.
> 
> I assume the context above is all about the ioctl interface?
> 
> So, when the card enters this non functional state, have you tried
> just reading a block through the regular I/O interface. Does it
> trigger a power cycle of the card - and then makes it functional
> again?
> 
>>
>> Signed-off-by: Mårten Lindahl <marten.lindahl@xxxxxxxx>
>> ---
>> Please note: This might not be the way we want to handle these cases,
>> but at least it lets us start the discussion. In which cases should the
>> mmc framework deal with error messages like ETIMEDOUT, and in which
>> cases should it be handled by userspace?
>> The mmc framework tries to recover a failed block request
>> (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card.
>> Would it be an idea to act in a similar way when an ioctl times out?
> 
> Maybe, it's a good idea to allow the similar reset for ioctls as we do
> for regular I/O requests. My concern with this though, is that we
> might allow user space to trigger a HW resets a bit too easily - and
> that could damage the card.
> 
> Did you consider this?
> 
>>
>>  drivers/mmc/core/block.c | 20 ++++++++++++++++++--
>>  1 file changed, 18 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
>> index 42e27a298218..d007b2af64d6 100644
>> --- a/drivers/mmc/core/block.c
>> +++ b/drivers/mmc/core/block.c
>> @@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)
>>   */
>>  static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)
>>  {
>> +       int type = rq_data_dir(req) == READ ? MMC_BLK_READ : MMC_BLK_WRITE;
>>         struct mmc_queue_req *mq_rq;
>>         struct mmc_card *card = mq->card;
>>         struct mmc_blk_data *md = mq->blkdata;
>> @@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)
>>         bool rpmb_ioctl;
>>         u8 **ext_csd;
>>         u32 status;
>> -       int ret;
>> +       int ret, retry = 1;
>>         int i;
>>
>>         mq_rq = req_to_mmc_queue_req(req);
>> @@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)
>>         case MMC_DRV_OP_IOCTL_RPMB:

SD cards do not have RPMB.  Did you mean eMMC?


>>                 idata = mq_rq->drv_op_data;
>>                 for (i = 0, ret = 0; i < mq_rq->ioc_count; i++) {
>> +cmd_do:
>>                         ret = __mmc_blk_ioctl_cmd(card, md, idata[i]);
>> -                       if (ret)
>> +                       if (ret == -ETIMEDOUT) {
>> +                               dev_warn(mmc_dev(card->host),
>> +                                        "error %d sending command\n", ret);
>> +cmd_reset:
>> +                               mmc_blk_reset_success(md, type);

mmc_blk_reset_success() is called upon success, not failure.  The reset will
not be attempted twice in a row, for a given type, without a "success" in
between.

>> +                               if (retry--) {
>> +                                       dev_warn(mmc_dev(card->host),
>> +                                                "power cycling card\n");
>> +                                       if (mmc_blk_reset
>> +                                           (md, card->host, type))
>> +                                               goto cmd_reset;
>> +                                       mmc_blk_reset_success(md, type);
>> +                                       goto cmd_do;
>> +                               }
>>                                 break;
>> +                       }
>>                 }
>>                 /* Always switch back to main area after RPMB access */
>>                 if (rpmb_ioctl)
>> --
>> 2.11.0
>>
> 
> Kind regards
> Uffe
> 




[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux