[PATCH] drivers: mmc: host: Retire MMC_GOLDFISH

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Roman Kiryanov <rkir@xxxxxxxxxx>

Android Studio Emulator no longer uses
this driver.

Signed-off-by: Roman Kiryanov <rkir@xxxxxxxxxx>
---
 drivers/mmc/host/Kconfig            |   7 -
 drivers/mmc/host/Makefile           |   1 -
 drivers/mmc/host/android-goldfish.c | 545 ----------------------------
 3 files changed, 553 deletions(-)
 delete mode 100644 drivers/mmc/host/android-goldfish.c

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 596f32637315..ad4678c9bac1 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -608,13 +608,6 @@ config MMC_DAVINCI
 	  If you have an DAVINCI board with a Multimedia Card slot,
 	  say Y or M here.  If unsure, say N.
 
-config MMC_GOLDFISH
-	tristate "goldfish qemu Multimedia Card Interface support"
-	depends on GOLDFISH || COMPILE_TEST
-	help
-	  This selects the Goldfish Multimedia card Interface emulation
-	  found on the Goldfish Android virtual device emulation.
-
 config MMC_SPI
 	tristate "MMC/SD/SDIO over SPI"
 	depends on SPI_MASTER
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 451c25fc2c69..7f97e97f7066 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -34,7 +34,6 @@ obj-$(CONFIG_MMC_ATMELMCI)	+= atmel-mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
 obj-$(CONFIG_MMC_MVSDIO)	+= mvsdio.o
 obj-$(CONFIG_MMC_DAVINCI)       += davinci_mmc.o
-obj-$(CONFIG_MMC_GOLDFISH)	+= android-goldfish.o
 obj-$(CONFIG_MMC_SPI)		+= mmc_spi.o
 ifeq ($(CONFIG_OF),y)
 obj-$(CONFIG_MMC_SPI)		+= of_mmc_spi.o
diff --git a/drivers/mmc/host/android-goldfish.c b/drivers/mmc/host/android-goldfish.c
deleted file mode 100644
index e878fdf8f20a..000000000000
--- a/drivers/mmc/host/android-goldfish.c
+++ /dev/null
@@ -1,545 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright 2007, Google Inc.
- *  Copyright 2012, Intel Inc.
- *
- *  based on omap.c driver, which was
- *  Copyright (C) 2004 Nokia Corporation
- *  Written by Tuukka Tikkanen and Juha Yrjölä <juha.yrjola@xxxxxxxxx>
- *  Misc hacks here and there by Tony Lindgren <tony@xxxxxxxxxxx>
- *  Other hacks (DMA, SD, etc) by David Brownell
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/major.h>
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/errno.h>
-#include <linux/hdreg.h>
-#include <linux/kdev_t.h>
-#include <linux/blkdev.h>
-#include <linux/mutex.h>
-#include <linux/scatterlist.h>
-#include <linux/mmc/mmc.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/card.h>
-
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/dma-mapping.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/timer.h>
-#include <linux/clk.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#include <asm/types.h>
-#include <linux/uaccess.h>
-
-#define DRIVER_NAME "goldfish_mmc"
-
-#define BUFFER_SIZE   16384
-
-#define GOLDFISH_MMC_READ(host, addr)   (readl(host->reg_base + addr))
-#define GOLDFISH_MMC_WRITE(host, addr, x)   (writel(x, host->reg_base + addr))
-
-enum {
-	/* status register */
-	MMC_INT_STATUS	        = 0x00,
-	/* set this to enable IRQ */
-	MMC_INT_ENABLE	        = 0x04,
-	/* set this to specify buffer address */
-	MMC_SET_BUFFER          = 0x08,
-
-	/* MMC command number */
-	MMC_CMD	                = 0x0C,
-
-	/* MMC argument */
-	MMC_ARG	                = 0x10,
-
-	/* MMC response (or R2 bits 0 - 31) */
-	MMC_RESP_0		        = 0x14,
-
-	/* MMC R2 response bits 32 - 63 */
-	MMC_RESP_1		        = 0x18,
-
-	/* MMC R2 response bits 64 - 95 */
-	MMC_RESP_2		        = 0x1C,
-
-	/* MMC R2 response bits 96 - 127 */
-	MMC_RESP_3		        = 0x20,
-
-	MMC_BLOCK_LENGTH        = 0x24,
-	MMC_BLOCK_COUNT         = 0x28,
-
-	/* MMC state flags */
-	MMC_STATE               = 0x2C,
-
-	/* MMC_INT_STATUS bits */
-
-	MMC_STAT_END_OF_CMD     = 1U << 0,
-	MMC_STAT_END_OF_DATA    = 1U << 1,
-	MMC_STAT_STATE_CHANGE   = 1U << 2,
-	MMC_STAT_CMD_TIMEOUT    = 1U << 3,
-
-	/* MMC_STATE bits */
-	MMC_STATE_INSERTED     = 1U << 0,
-	MMC_STATE_READ_ONLY    = 1U << 1,
-};
-
-/*
- * Command types
- */
-#define OMAP_MMC_CMDTYPE_BC	0
-#define OMAP_MMC_CMDTYPE_BCR	1
-#define OMAP_MMC_CMDTYPE_AC	2
-#define OMAP_MMC_CMDTYPE_ADTC	3
-
-
-struct goldfish_mmc_host {
-	struct mmc_request	*mrq;
-	struct mmc_command	*cmd;
-	struct mmc_data		*data;
-	struct device		*dev;
-	unsigned char		id; /* 16xx chips have 2 MMC blocks */
-	void			*virt_base;
-	unsigned int		phys_base;
-	int			irq;
-	unsigned char		bus_mode;
-	unsigned char		hw_bus_mode;
-
-	unsigned int		sg_len;
-	unsigned		dma_done:1;
-	unsigned		dma_in_use:1;
-
-	void __iomem		*reg_base;
-};
-
-static inline int
-goldfish_mmc_cover_is_open(struct goldfish_mmc_host *host)
-{
-	return 0;
-}
-
-static ssize_t
-goldfish_mmc_show_cover_switch(struct device *dev,
-			       struct device_attribute *attr, char *buf)
-{
-	struct goldfish_mmc_host *host = dev_get_drvdata(dev);
-
-	return sprintf(buf, "%s\n", goldfish_mmc_cover_is_open(host) ? "open" :
-		       "closed");
-}
-
-static DEVICE_ATTR(cover_switch, S_IRUGO, goldfish_mmc_show_cover_switch, NULL);
-
-static void
-goldfish_mmc_start_command(struct goldfish_mmc_host *host, struct mmc_command *cmd)
-{
-	u32 cmdreg;
-	u32 resptype;
-	u32 cmdtype;
-
-	host->cmd = cmd;
-
-	resptype = 0;
-	cmdtype = 0;
-
-	/* Our hardware needs to know exact type */
-	switch (mmc_resp_type(cmd)) {
-	case MMC_RSP_NONE:
-		break;
-	case MMC_RSP_R1:
-	case MMC_RSP_R1B:
-		/* resp 1, 1b, 6, 7 */
-		resptype = 1;
-		break;
-	case MMC_RSP_R2:
-		resptype = 2;
-		break;
-	case MMC_RSP_R3:
-		resptype = 3;
-		break;
-	default:
-		dev_err(mmc_dev(mmc_from_priv(host)),
-			"Invalid response type: %04x\n", mmc_resp_type(cmd));
-		break;
-	}
-
-	if (mmc_cmd_type(cmd) == MMC_CMD_ADTC)
-		cmdtype = OMAP_MMC_CMDTYPE_ADTC;
-	else if (mmc_cmd_type(cmd) == MMC_CMD_BC)
-		cmdtype = OMAP_MMC_CMDTYPE_BC;
-	else if (mmc_cmd_type(cmd) == MMC_CMD_BCR)
-		cmdtype = OMAP_MMC_CMDTYPE_BCR;
-	else
-		cmdtype = OMAP_MMC_CMDTYPE_AC;
-
-	cmdreg = cmd->opcode | (resptype << 8) | (cmdtype << 12);
-
-	if (host->bus_mode == MMC_BUSMODE_OPENDRAIN)
-		cmdreg |= 1 << 6;
-
-	if (cmd->flags & MMC_RSP_BUSY)
-		cmdreg |= 1 << 11;
-
-	if (host->data && !(host->data->flags & MMC_DATA_WRITE))
-		cmdreg |= 1 << 15;
-
-	GOLDFISH_MMC_WRITE(host, MMC_ARG, cmd->arg);
-	GOLDFISH_MMC_WRITE(host, MMC_CMD, cmdreg);
-}
-
-static void goldfish_mmc_xfer_done(struct goldfish_mmc_host *host,
-				   struct mmc_data *data)
-{
-	if (host->dma_in_use) {
-		enum dma_data_direction dma_data_dir;
-
-		dma_data_dir = mmc_get_dma_dir(data);
-
-		if (dma_data_dir == DMA_FROM_DEVICE) {
-			/*
-			 * We don't really have DMA, so we need
-			 * to copy from our platform driver buffer
-			 */
-			sg_copy_from_buffer(data->sg, 1, host->virt_base,
-					data->sg->length);
-		}
-		host->data->bytes_xfered += data->sg->length;
-		dma_unmap_sg(mmc_dev(mmc_from_priv(host)), data->sg,
-			     host->sg_len, dma_data_dir);
-	}
-
-	host->data = NULL;
-	host->sg_len = 0;
-
-	/*
-	 * NOTE:  MMC layer will sometimes poll-wait CMD13 next, issuing
-	 * dozens of requests until the card finishes writing data.
-	 * It'd be cheaper to just wait till an EOFB interrupt arrives...
-	 */
-
-	if (!data->stop) {
-		host->mrq = NULL;
-		mmc_request_done(mmc_from_priv(host), data->mrq);
-		return;
-	}
-
-	goldfish_mmc_start_command(host, data->stop);
-}
-
-static void goldfish_mmc_end_of_data(struct goldfish_mmc_host *host,
-				     struct mmc_data *data)
-{
-	if (!host->dma_in_use) {
-		goldfish_mmc_xfer_done(host, data);
-		return;
-	}
-	if (host->dma_done)
-		goldfish_mmc_xfer_done(host, data);
-}
-
-static void goldfish_mmc_cmd_done(struct goldfish_mmc_host *host,
-				  struct mmc_command *cmd)
-{
-	host->cmd = NULL;
-	if (cmd->flags & MMC_RSP_PRESENT) {
-		if (cmd->flags & MMC_RSP_136) {
-			/* response type 2 */
-			cmd->resp[3] =
-				GOLDFISH_MMC_READ(host, MMC_RESP_0);
-			cmd->resp[2] =
-				GOLDFISH_MMC_READ(host, MMC_RESP_1);
-			cmd->resp[1] =
-				GOLDFISH_MMC_READ(host, MMC_RESP_2);
-			cmd->resp[0] =
-				GOLDFISH_MMC_READ(host, MMC_RESP_3);
-		} else {
-			/* response types 1, 1b, 3, 4, 5, 6 */
-			cmd->resp[0] =
-				GOLDFISH_MMC_READ(host, MMC_RESP_0);
-		}
-	}
-
-	if (host->data == NULL || cmd->error) {
-		host->mrq = NULL;
-		mmc_request_done(mmc_from_priv(host), cmd->mrq);
-	}
-}
-
-static irqreturn_t goldfish_mmc_irq(int irq, void *dev_id)
-{
-	struct goldfish_mmc_host *host = (struct goldfish_mmc_host *)dev_id;
-	u16 status;
-	int end_command = 0;
-	int end_transfer = 0;
-	int state_changed = 0;
-	int cmd_timeout = 0;
-
-	while ((status = GOLDFISH_MMC_READ(host, MMC_INT_STATUS)) != 0) {
-		GOLDFISH_MMC_WRITE(host, MMC_INT_STATUS, status);
-
-		if (status & MMC_STAT_END_OF_CMD)
-			end_command = 1;
-
-		if (status & MMC_STAT_END_OF_DATA)
-			end_transfer = 1;
-
-		if (status & MMC_STAT_STATE_CHANGE)
-			state_changed = 1;
-
-                if (status & MMC_STAT_CMD_TIMEOUT) {
-			end_command = 0;
-			cmd_timeout = 1;
-                }
-	}
-
-	if (cmd_timeout) {
-		struct mmc_request *mrq = host->mrq;
-		mrq->cmd->error = -ETIMEDOUT;
-		host->mrq = NULL;
-		mmc_request_done(mmc_from_priv(host), mrq);
-	}
-
-	if (end_command)
-		goldfish_mmc_cmd_done(host, host->cmd);
-
-	if (end_transfer) {
-		host->dma_done = 1;
-		goldfish_mmc_end_of_data(host, host->data);
-	} else if (host->data != NULL) {
-		/*
-		 * WORKAROUND -- after porting this driver from 2.6 to 3.4,
-		 * during device initialization, cases where host->data is
-		 * non-null but end_transfer is false would occur. Doing
-		 * nothing in such cases results in no further interrupts,
-		 * and initialization failure.
-		 * TODO -- find the real cause.
-		 */
-		host->dma_done = 1;
-		goldfish_mmc_end_of_data(host, host->data);
-	}
-
-	if (state_changed) {
-		u32 state = GOLDFISH_MMC_READ(host, MMC_STATE);
-		pr_info("%s: Card detect now %d\n", __func__,
-			(state & MMC_STATE_INSERTED));
-		mmc_detect_change(mmc_from_priv(host), 0);
-	}
-
-	if (!end_command && !end_transfer && !state_changed && !cmd_timeout) {
-		status = GOLDFISH_MMC_READ(host, MMC_INT_STATUS);
-		dev_info(mmc_dev(mmc_from_priv(host)), "spurious irq 0x%04x\n",
-			 status);
-		if (status != 0) {
-			GOLDFISH_MMC_WRITE(host, MMC_INT_STATUS, status);
-			GOLDFISH_MMC_WRITE(host, MMC_INT_ENABLE, 0);
-		}
-	}
-
-	return IRQ_HANDLED;
-}
-
-static void goldfish_mmc_prepare_data(struct goldfish_mmc_host *host,
-				      struct mmc_request *req)
-{
-	struct mmc_data *data = req->data;
-	int block_size;
-	unsigned sg_len;
-	enum dma_data_direction dma_data_dir;
-
-	host->data = data;
-	if (data == NULL) {
-		GOLDFISH_MMC_WRITE(host, MMC_BLOCK_LENGTH, 0);
-		GOLDFISH_MMC_WRITE(host, MMC_BLOCK_COUNT, 0);
-		host->dma_in_use = 0;
-		return;
-	}
-
-	block_size = data->blksz;
-
-	GOLDFISH_MMC_WRITE(host, MMC_BLOCK_COUNT, data->blocks - 1);
-	GOLDFISH_MMC_WRITE(host, MMC_BLOCK_LENGTH, block_size - 1);
-
-	/*
-	 * Cope with calling layer confusion; it issues "single
-	 * block" writes using multi-block scatterlists.
-	 */
-	sg_len = (data->blocks == 1) ? 1 : data->sg_len;
-
-	dma_data_dir = mmc_get_dma_dir(data);
-
-	host->sg_len = dma_map_sg(mmc_dev(mmc_from_priv(host)), data->sg,
-				  sg_len, dma_data_dir);
-	host->dma_done = 0;
-	host->dma_in_use = 1;
-
-	if (dma_data_dir == DMA_TO_DEVICE) {
-		/*
-		 * We don't really have DMA, so we need to copy to our
-		 * platform driver buffer
-		 */
-		sg_copy_to_buffer(data->sg, 1, host->virt_base,
-				data->sg->length);
-	}
-}
-
-static void goldfish_mmc_request(struct mmc_host *mmc, struct mmc_request *req)
-{
-	struct goldfish_mmc_host *host = mmc_priv(mmc);
-
-	WARN_ON(host->mrq != NULL);
-
-	host->mrq = req;
-	goldfish_mmc_prepare_data(host, req);
-	goldfish_mmc_start_command(host, req->cmd);
-}
-
-static void goldfish_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
-{
-	struct goldfish_mmc_host *host = mmc_priv(mmc);
-
-	host->bus_mode = ios->bus_mode;
-	host->hw_bus_mode = host->bus_mode;
-}
-
-static int goldfish_mmc_get_ro(struct mmc_host *mmc)
-{
-	uint32_t state;
-	struct goldfish_mmc_host *host = mmc_priv(mmc);
-
-	state = GOLDFISH_MMC_READ(host, MMC_STATE);
-	return ((state & MMC_STATE_READ_ONLY) != 0);
-}
-
-static const struct mmc_host_ops goldfish_mmc_ops = {
-	.request	= goldfish_mmc_request,
-	.set_ios	= goldfish_mmc_set_ios,
-	.get_ro		= goldfish_mmc_get_ro,
-};
-
-static int goldfish_mmc_probe(struct platform_device *pdev)
-{
-	struct mmc_host *mmc;
-	struct goldfish_mmc_host *host = NULL;
-	struct resource *res;
-	int ret = 0;
-	int irq;
-	dma_addr_t buf_addr;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	irq = platform_get_irq(pdev, 0);
-	if (res == NULL || irq < 0)
-		return -ENXIO;
-
-	mmc = mmc_alloc_host(sizeof(struct goldfish_mmc_host), &pdev->dev);
-	if (mmc == NULL) {
-		ret = -ENOMEM;
-		goto err_alloc_host_failed;
-	}
-
-	host = mmc_priv(mmc);
-
-	pr_err("mmc: Mapping %lX to %lX\n", (long)res->start, (long)res->end);
-	host->reg_base = ioremap(res->start, resource_size(res));
-	if (host->reg_base == NULL) {
-		ret = -ENOMEM;
-		goto ioremap_failed;
-	}
-	host->virt_base = dma_alloc_coherent(&pdev->dev, BUFFER_SIZE,
-					     &buf_addr, GFP_KERNEL);
-
-	if (host->virt_base == 0) {
-		ret = -ENOMEM;
-		goto dma_alloc_failed;
-	}
-	host->phys_base = buf_addr;
-
-	host->id = pdev->id;
-	host->irq = irq;
-
-	mmc->ops = &goldfish_mmc_ops;
-	mmc->f_min = 400000;
-	mmc->f_max = 24000000;
-	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-	mmc->caps = MMC_CAP_4_BIT_DATA;
-	mmc->caps2 = MMC_CAP2_NO_SDIO;
-
-	/* Use scatterlist DMA to reduce per-transfer costs.
-	 * NOTE max_seg_size assumption that small blocks aren't
-	 * normally used (except e.g. for reading SD registers).
-	 */
-	mmc->max_segs = 32;
-	mmc->max_blk_size = 2048;	/* MMC_BLOCK_LENGTH is 11 bits (+1) */
-	mmc->max_blk_count = 2048;	/* MMC_BLOCK_COUNT is 11 bits (+1) */
-	mmc->max_req_size = BUFFER_SIZE;
-	mmc->max_seg_size = mmc->max_req_size;
-
-	ret = request_irq(host->irq, goldfish_mmc_irq, 0, DRIVER_NAME, host);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed IRQ Adding goldfish MMC\n");
-		goto err_request_irq_failed;
-	}
-
-	host->dev = &pdev->dev;
-	platform_set_drvdata(pdev, host);
-
-	ret = device_create_file(&pdev->dev, &dev_attr_cover_switch);
-	if (ret)
-		dev_warn(mmc_dev(mmc), "Unable to create sysfs attributes\n");
-
-	GOLDFISH_MMC_WRITE(host, MMC_SET_BUFFER, host->phys_base);
-	GOLDFISH_MMC_WRITE(host, MMC_INT_ENABLE,
-			   MMC_STAT_END_OF_CMD | MMC_STAT_END_OF_DATA |
-			   MMC_STAT_STATE_CHANGE | MMC_STAT_CMD_TIMEOUT);
-
-	mmc_add_host(mmc);
-	return 0;
-
-err_request_irq_failed:
-	dma_free_coherent(&pdev->dev, BUFFER_SIZE, host->virt_base,
-			  host->phys_base);
-dma_alloc_failed:
-	iounmap(host->reg_base);
-ioremap_failed:
-	mmc_free_host(mmc);
-err_alloc_host_failed:
-	return ret;
-}
-
-static int goldfish_mmc_remove(struct platform_device *pdev)
-{
-	struct goldfish_mmc_host *host = platform_get_drvdata(pdev);
-	struct mmc_host *mmc = mmc_from_priv(host);
-
-	BUG_ON(host == NULL);
-
-	mmc_remove_host(mmc);
-	free_irq(host->irq, host);
-	dma_free_coherent(&pdev->dev, BUFFER_SIZE, host->virt_base, host->phys_base);
-	iounmap(host->reg_base);
-	mmc_free_host(mmc);
-	return 0;
-}
-
-static struct platform_driver goldfish_mmc_driver = {
-	.probe		= goldfish_mmc_probe,
-	.remove		= goldfish_mmc_remove,
-	.driver		= {
-		.name	= DRIVER_NAME,
-		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
-	},
-};
-
-module_platform_driver(goldfish_mmc_driver);
-MODULE_LICENSE("GPL v2");
-- 
2.30.0.478.g8a0d178c01-goog





[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux