[...] > >> >> >> The SDcard for Keem Bay SOC does not have its own voltage regulator. > >> >> >> There are 2 places to control the voltage. > >> >> >> 1) By setting the AON register calling system-level platform > >> >> >> management > >> >> >layer (SMC) > >> >> >> to set the I/O pads voltage for particular GPIOs line for clk,data and > >cmd. > >> >> >> The reason why I use this keembay_sd_voltage_selection() via > >> >> >> smccc > >> >> >interface it because during voltage switching > >> >> >> I need to access to AON register. On a secure system, we > >> >> >> could not > >> >> >directly access to AON register due to some security concern from > >> >> >driver side, thus > >> >> >> cannot exposed any register or address. > >> >> >> 2) By controlling the GPIO expander value to drive either 1.8V > >> >> >> or 3.3V for > >> >> >power mux input. > >> >> > > >> >> >I see, thanks for clarifying. > >> >> > > >> >> >To me, it sounds like the best fit is to implement a pinctrl (to > >> >> >manage the I/O > >> >> >pads) and a GPIO regulator. > >> >> > > >> >> Even with pinctrl, i still need to use the > >> >> keembay_sd_voltage_selection() > >> >thingy for AON register. > >> > > >> >Yes, I am fine by that. > >> > > >> >Although, as it's really a pinctrl, it deserves to be modelled like > >> >that. Not as a soc specific hack in a mmc host driver. > >> > > >> >> Plus, the GPIO pin that control the sd-voltage is in GPIO Expander > >> >> not using > >> >Keembay SOC GPIO Pin. > >> >> The best option is using the gpio consumer function to toggle the pin. > >> > > >> >As I said, please no. > >> > > >> >The common way to model this is as a GPIO regulator. In this way, you > >> >can even rely on existing mmc DT bindings. All you have to do is to > >> >hook up a vqmmc supply to the mmc node. > >> > > >> >To be clear, as long as there are no arguments for why a pinctrl and > >> >GPIO regulator can't be used - I am not going to pick up the patches. > >> As I mentioned The SDcard does not have its own voltage regulator. > >> It only uses the voltage rails on the mux input. > >> > >> There are 2 things need to be configured before getting the output voltage: > >> > >> 1) V_VDDIO_B : > >> Supplied voltage applied to I/O Rail which is controlled from the Always on > >domain using specific bits in AON_CFG1 register. > >> This is where we set for V_VDDIO_B using the > >keembay_sd_voltage_selection() to set either 1.8v or 3.3v depending on the bit > >value. > >> IMHO, we do not pinctrl to do this. > >> > >> 2) V_VDDIO_B_MAIN: > >> The output V_VDDIO_B_MAIN (OUT1) will be either V_3P3_MAIN (IN1) or > >> V_1P8_MAIN (IN2), depending on the state of GPIO expander Pin value. There > >is a POWER MUX involving here. > >> IMHO, we do not need any gpio regulator/regulator api hook up for this. > >> Most important thing, there is no regulator ic at all. > >> We still need to manually control and toggle the pin value. > >> > >> The final IO voltage is set by V_VDDIO_B (= V_VDDIO_B_MAIN after passing > >through voltage sense resistor). > >> > >> Hope this will clarify. > > > >I think I get it, thanks. > > > >Again, I haven't seen any reasons for why this can't be modelled as a pinctrl and > >a gpio-regulator. So, please convert it to that. > For gpio-regulator, I believe I could not use the current gpio-regulator.c framework as there is no consumer API for me to change the state of gpio pin during voltage switching. The consumer API you want to use, is the regulator consumer API, regulator_enable|disable(), for example. Although, as I stated earlier, the mmc core already provides helper functions for this. I suggest you have a look at mmc_regulator_set_vqmmc() and how it's used by other mmc host drivers. > Do I need to create a specific gpio-regulator driver under drivers/regulator for keem bay? > > I don't think so. Please have a look at Documentation/devicetree/bindings/regulator/gpio-regulator.yaml. This allows you to specify your GPIO regulator in DT. Then from the mmc node you add a "vqmmc-supply" specifier with the phandle to the regulator - that should be it. Kind regards Uffe
