Hi All,
Now the MMC read/write stack will always wait for previous request is
completed by mmc_blk_rw_wait(), before sending a new request to hardware,
or queue a work to complete request, that will bring context switching
overhead, especially for high I/O per second rates, to affect the IO
performance.
Thus this patch set will introduce the MMC software command queue support
based on command queue engine's interfaces, and set the queue depth as 64
to allow more requests can be be prepared, merged and inserted into IO
scheduler, but we only allow 2 requests in flight, that is enough to let
the irq handler always trigger the next request without a context switch,
as well as avoiding a long latency.
Moreover we can expand the MMC software queue interface to support
MMC packed request or packed command instead of adding new interfaces,
according to previosus discussion.
Below are some comparison data with fio tool. The fio command I used
is like below with changing the '--rw' parameter and enabling the direct
IO flag to measure the actual hardware transfer speed in 4K block size.
./fio --filename=/dev/mmcblk0p30 --direct=1 --iodepth=20 --rw=read --bs=4K --size=1G --group_reporting --numjobs=20 --name=test_read
My eMMC card working at HS400 Enhanced strobe mode:
[ 2.229856] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[ 2.237566] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[ 2.242621] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[ 2.249110] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[ 2.255307] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0)
1. Without MMC software queue
I tested 5 times for each case and output a average speed.
1) Sequential read:
Speed: 59.4MiB/s, 63.4MiB/s, 57.5MiB/s, 57.2MiB/s, 60.8MiB/s
Average speed: 59.66MiB/s
2) Random read:
Speed: 26.9MiB/s, 26.9MiB/s, 27.1MiB/s, 27.1MiB/s, 27.2MiB/s
Average speed: 27.04MiB/s
3) Sequential write:
Speed: 71.6MiB/s, 72.5MiB/s, 72.2MiB/s, 64.6MiB/s, 67.5MiB/s
Average speed: 69.68MiB/s
4) Random write:
Speed: 36.3MiB/s, 35.4MiB/s, 38.6MiB/s, 34MiB/s, 35.5MiB/s
Average speed: 35.96MiB/s
2. With MMC software queue
I tested 5 times for each case and output a average speed.
1) Sequential read:
Speed: 59.2MiB/s, 60.4MiB/s, 63.6MiB/s, 60.3MiB/s, 59.9MiB/s
Average speed: 60.68MiB/s
2) Random read:
Speed: 31.3MiB/s, 31.4MiB/s, 31.5MiB/s, 31.3MiB/s, 31.3MiB/s
Average speed: 31.36MiB/s
3) Sequential write:
Speed: 71MiB/s, 71.8MiB/s, 72.3MiB/s, 72.2MiB/s, 71MiB/s
Average speed: 71.66MiB/s
4) Random write:
Speed: 68.9MiB/s, 68.7MiB/s, 68.8MiB/s, 68.6MiB/s, 68.8MiB/s
Average speed: 68.76MiB/s
Form above data, we can see the MMC software queue can help to improve some
performance obviously for random read and write, though no obvious improvement
for sequential read and write.
Any comments are welcome. Thanks a lot.
Changes from v7:
- Add reviewed tag from Arnd.
- Use the 'hsq' acronym for varibles and functions in the core layer.
- Check the 'card->ext_csd.cmdq_en' in cqhci.c to make sure the CQE
can work normally.
- Add a new patch to enable the host software queue for the SD card.
- Use the default MMC queue depth for host software queue.
Changes from v6:
- Change the patch order and set host->always_defer_done = true for the
Spreadtrum host driver.
Changes from v5:
- Modify the condition of defering to complete request suggested by Adrian.
Changes from v4:
- Add a seperate patch to introduce a variable to defer to complete
data requests for some host drivers, when using host software queue.
Changes from v3:
- Use host software queue instead of sqhci.
- Fix random config building issue.
- Change queue depth to 32, but still only allow 2 requests in flight.
- Update the testing data.
Changes from v2:
- Remove reference to 'struct cqhci_host' and 'struct cqhci_slot',
instead adding 'struct sqhci_host', which is only used by software queue.
Changes from v1:
- Add request_done ops for sdhci_ops.
- Replace virtual command queue with software queue for functions and
variables.
- Rename the software queue file and add sqhci.h header file.
Baolin Wang (5):
mmc: Add MMC host software queue support
mmc: core: Enable the MMC host software queue for the SD card
mmc: host: sdhci: Add request_done ops for struct sdhci_ops
mmc: host: sdhci: Add a variable to defer to complete requests if
needed
mmc: host: sdhci-sprd: Add software queue support
drivers/mmc/core/block.c | 61 ++++++++
drivers/mmc/core/mmc.c | 13 +-
drivers/mmc/core/queue.c | 22 ++-
drivers/mmc/core/sd.c | 10 ++
drivers/mmc/host/Kconfig | 8 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/cqhci.c | 3 +
drivers/mmc/host/mmc_hsq.c | 343 +++++++++++++++++++++++++++++++++++++++++
drivers/mmc/host/mmc_hsq.h | 30 ++++
drivers/mmc/host/sdhci-sprd.c | 28 ++++
drivers/mmc/host/sdhci.c | 14 +-
drivers/mmc/host/sdhci.h | 3 +
include/linux/mmc/host.h | 3 +
13 files changed, 529 insertions(+), 10 deletions(-)
create mode 100644 drivers/mmc/host/mmc_hsq.c
create mode 100644 drivers/mmc/host/mmc_hsq.h
--
1.7.9.5
