Hi,
On Tue, Nov 12, 2019 at 4:28 AM Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
>
> On Tue, 12 Nov 2019 at 01:51, Doug Anderson <dianders@xxxxxxxxxxxx> wrote:
> >
> > Hi,
> >
> > On Sat, Nov 9, 2019 at 2:31 AM Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
> > >
> > > Changes in v2:
> > > - Add adaptations to the mwifiex driver.
> > > - Keep existing syncronous reset behaviour if the SDIO card has a single
> > > func driver.
> > >
> > > It has turned out that it's not a good idea to try to power cycle and to
> > > re-initialize the SDIO card, as currently done through mmc_hw_reset(). This
> > > because there may be multiple SDIO funcs attached to the same SDIO card and
> > > some of the others that didn't execute the call to mmc_hw_reset(), may then
> > > simply experience an undefined behaviour.
> > >
> > > The following patches in this series attempts to address this problem, by
> > > reworking the mmc_hw_reset() behaviour for SDIO and by adopting the Marvel
> > > mwifiex driver to these changes.
> > >
> > > Note that, I don't have the HW at hand so the the code has only compile tested.
> > > Test on HW is greatly appreciated!
> > >
> > > Ulf Hansson (3):
> > > mwifiex: Re-work support for SDIO HW reset
> > > mmc: core: Drop check for mmc_card_is_removable() in mmc_rescan()
> > > mmc: core: Re-work HW reset for SDIO cards
> > >
> > > drivers/mmc/core/core.c | 12 +++-----
> > > drivers/mmc/core/core.h | 2 ++
> > > drivers/mmc/core/sdio.c | 28 ++++++++++++++++-
> > > drivers/mmc/core/sdio_bus.c | 9 +++++-
> > > drivers/net/wireless/marvell/mwifiex/main.c | 6 +++-
> > > drivers/net/wireless/marvell/mwifiex/main.h | 1 +
> > > drivers/net/wireless/marvell/mwifiex/sdio.c | 33 ++++++++++++++-------
> > > include/linux/mmc/card.h | 1 +
> > > 8 files changed, 70 insertions(+), 22 deletions(-)
> >
> > I put this on rk3288-veyron-jerry atop v5.4-rc7 and I could run my
> > test case for a while, AKA I got over 50 cycles of:
> >
> > ---
> >
> > for i in $(seq 1000); do
> > echo "LOOP $i --------"
> > echo 1 > /sys/kernel/debug/mwifiex/mlan0/reset
> >
> > while true; do
> > if ! ping6 -w15 -c1 "${GW}" >/dev/null 2>&1; then
> > fail=$(( fail + 1 ))
> > echo "Fail WiFi ${fail}"
> > if [[ ${fail} == 3 ]]; then
> > exit 1
> > fi
> > else
> > fail=0
> > break
> > fi
> > done
> >
> > hciconfig hci0 down
> > sleep 1
> > if ! hciconfig hci0 up; then
> > echo "Fail BT"
> > exit 1
> > fi
> >
> > done
> >
> > ---
> >
> > NOTE: with no patches I couldn't even get my test case to pass w/out
> > the BT bits and I swear that used to work before. ...but I didn't
> > debug since the end result (with full card hotplug) is happy-working
> > for me. I'll still use it as further argument that (IMO) full unplug
> > / plug of the card is better it uses more standard code paths and is
> > less likely to break. ;-)
> >
> > Tested-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
>
> Thanks, I add this to the series and make a re-spin.
>
> What do you think about tagging the patches for stable?
>
> I guess there is a risk that we may "break" the other two users of
> mmc_hw_reset(). But, as I said, in that case those needs to be fixed
> anyways.
I'm not sure how to make that judgement call. Certainly it would help
anyone using the Marvell case and the Marvell case was pretty broken
before.
How about this: if you can get a Tested-by from the other users then
I'd be good with a general CC: stable. Otherwise, I'd be OK with a CC
to stable for 5.4, but I'd be a little hesitant to send it back to
older kernels (even though it certainly applies and fixes problems).
At least in the case of Chrome OS we already have a workable solution
for our 4.19 tree (my previous patches), and I'd guess anyone testing
on real hardware is either not seeing problems or has their own
private patches already. If things have been sitting stable on 5.4
for a while and no problems were reported, then we could consider
going back further?
-Doug
