On Wed, 24 Jul 2019 at 20:56, Adrian Hunter <adrian.hunter@xxxxxxxxx> wrote:
>
> On 24/07/19 5:21 AM, Baolin Wang wrote:
> > On Tue, 23 Jul 2019 at 20:39, Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
> >>
> >> On Tue, 23 Jul 2019 at 05:05, Baolin Wang <baolin.wang@xxxxxxxxxx> wrote:
> >>>
> >>> Hi Ulf,
> >>>
> >>> On Mon, 22 Jul 2019 at 19:54, Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
> >>>>
> >>>> On Wed, 17 Jul 2019 at 04:29, Baolin Wang <baolin.wang@xxxxxxxxxx> wrote:
> >>>>>
> >>>>> In sdhci_runtime_resume_host() function, we will always do software reset
> >>>>> for all, which will cause Spreadtrum host controller work abnormally after
> >>>>> resuming.
> >>>>
> >>>> What does "software reset for all" means?
> >>>
> >>> The SD host controller specification defines 3 types software reset:
> >>> software reset for data line, software reset for command line and
> >>> software reset for all.
> >>> Software reset for all means this reset affects the entire Host
> >>> controller except for the card detection circuit.
> >>
> >> Thanks for clarifying, please update the changelog accordingly.
> >
> > Sure, sorry for confusing.
> >
> >>
> >>>
> >>>>
> >>>>>
> >>>>> Thus for Spreadtrum platform that will not power down the SD/eMMC card during
> >>>>> runtime suspend, we should not do software reset for all.
> >>>>
> >>>> Normally, sdhci hosts that enters runtime suspend doesn't power off
> >>>> the card (there are some exceptions like PCI variants).
> >>>
> >>> Yes, same as our controller.
> >>>
> >>>>
> >>>> So, what's so special here and how does the reset come into play? I
> >>>> don't see sdhci doing a reset in sdhci_runtime_suspend|resume_host()
> >>>> and nor doesn the callback from the sdhci-sprd.c variant doing it.
> >>>
> >>> In sdhci_runtime_resume_host(), it will issue sdhci_init(host, 0) to
> >>> issue software reset for all.
> >>
> >> Aha, I didn't read the code carefully enough. Apologize for the noise.
> >
> > No worries :)
> >
> >>>
> >>>>
> >>>>> To fix this
> >>>>> issue, adding a specific reset operation that adds one condition to validate
> >>>>> the power mode to decide if we can do software reset for all or just reset
> >>>>> command and data lines.
> >>>>>
> >>>>> Signed-off-by: Baolin Wang <baolin.wang@xxxxxxxxxx>
> >>>>> ---
> >>>>> Changess from v3:
> >>>>> - Use ios.power_mode to validate if the card is power down or not.
> >>>>>
> >>>>> Changes from v2:
> >>>>> - Simplify the sdhci_sprd_reset() by issuing sdhci_reset().
> >>>>>
> >>>>> Changes from v1:
> >>>>> - Add a specific reset operation instead of changing the core to avoid
> >>>>> affecting other hardware.
> >>>>> ---
> >>>>> drivers/mmc/host/sdhci-sprd.c | 19 ++++++++++++++++++-
> >>>>> 1 file changed, 18 insertions(+), 1 deletion(-)
> >>>>>
> >>>>> diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c
> >>>>> index 603a5d9..94f9726 100644
> >>>>> --- a/drivers/mmc/host/sdhci-sprd.c
> >>>>> +++ b/drivers/mmc/host/sdhci-sprd.c
> >>>>> @@ -373,6 +373,23 @@ static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host)
> >>>>> return 1 << 31;
> >>>>> }
> >>>>>
> >>>>> +static void sdhci_sprd_reset(struct sdhci_host *host, u8 mask)
> >>>>> +{
> >>>>> + struct mmc_host *mmc = host->mmc;
> >>>>> +
> >>>>> + /*
> >>>>> + * When try to reset controller after runtime suspend, we should not
> >>>>> + * reset for all if the SD/eMMC card is not power down, just reset
> >>>>> + * command and data lines instead. Otherwise will meet some strange
> >>>>> + * behaviors for Spreadtrum host controller.
> >>>>> + */
> >>>>> + if (host->runtime_suspended && (mask & SDHCI_RESET_ALL) &&
> >>>>> + mmc->ios.power_mode == MMC_POWER_ON)
> >>>>> + mask = SDHCI_RESET_CMD | SDHCI_RESET_DATA;
> >>>>
> >>>> Can sdhci_sprd_reset() be called when the host is runtime suspended?
> >>>
> >>> When host tries to runtime resume in sdhci_runtime_resume_host(), it
> >>> will call reset operation to do software reset.
> >>
> >> Right, I see that now, thanks for clarifying.
> >>
> >> However, there are still some weird things going on in
> >> sdhci_runtime_resume_host(). Like why is host->ops->enable_dma()
> >> called first, directly from sdhci_runtime_resume_host(), then again in
> >> sdhci_do_reset(), after host->ops->reset() has been called. Looks like
> >> the first call to ->enable_dma() doesn't make sense?
> >
> > I am mot sure, since our host did not supply enable_dma() operation.
> > This logic was used by some other hardware and worked well, I am not
> > sure if it can reveal some issues if we change the logic here.
> >
> > Adrian, could you help to explain why we put enable_dma() in front of
> > software reset?
>
> No reason I can see. But if you add a parameter to avoid a full reset, then
> the ->enable_dma will be needed in that case.
OK. I'll keep it.
>
> >
> >>
> >>>
> >>>> That sounds like a bug to me, no?
> >>>
> >>> Since our controller will meet some strange behaviors if we do
> >>> software reset for all in sdhci_runtime_resume_host(), and try to
> >>> avoid changing the core logic of sdhci_runtime_resume_host() used by
> >>> other hardware controllers, thus I introduced a specific reset ops and
> >>> added some condition to make sure we just do software reset command
> >>> and data lines from runtime suspend state.
> >>
> >> I understand, but perhaps it would become more clear if
> >> sdhci_runtime_resume_host() is re-factored a bit. Maybe the caller can
> >> give it some new parameter to let it decide if a SDHCI_RESET_ALL shall
> >> be done or not.
> >
> > Yes, sounds reasonable, but need change other host drivers which
> > issued the sdhci_runtime_resume_host().
> >
> > Adrian, if you also agree with Ulf's suggestion, then I will post new
> > patches to add a parameter to decide the reset mode. Thanks.
>
> Sounds fine.
OK. Thanks for your input.
--
Baolin Wang
Best Regards
