On 3/06/19 4:48 PM, Ulf Hansson wrote:
> + Adrian
>
> On Thu, 30 May 2019 at 11:20, Takao Orito <orito.takao@xxxxxxxxxxxxx> wrote:
>>
>> SD Host controller on Milbeaut consists of two controller parts.
>> One is core controller F_SDH30, this is similar to sdhci-fujitsu
>> controller.
>> Another is bridge controller.
>> This bridge controller is not compatible with sdhci-fujitsu controller.
>> This is special for Milbeaut series. This has some functions.
>> For example, reset control, clock enable/select for SDR50/25/12, set
>> property of SD physical pins, retuning control, set capabilityies.
>>
>> This bridge controller requires special procedures at reset or clock
>> enablement or change for further tuning of clock.
>>
>> Signed-off-by: Takao Orito <orito.takao@xxxxxxxxxxxxx>
>
> This looks good to me, however I have looped in Adrian who maintains
> SDHCI drivers, to allow him to provide some input.
Looks OK.
Could address the output of: scripts/checkpatch.pl --strict
And the "readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff" thing only
makes sense for PCI.
Nevertheless:
Acked-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>
>
> Kind regards
> Uffe
>
>
>> ---
>> drivers/mmc/host/Kconfig | 11 ++
>> drivers/mmc/host/Makefile | 1 +
>> drivers/mmc/host/sdhci-milbeaut.c | 362 ++++++++++++++++++++++++++++++++++++++
>> drivers/mmc/host/sdhci_f_sdh30.c | 26 +--
>> drivers/mmc/host/sdhci_f_sdh30.h | 32 ++++
>> 5 files changed, 407 insertions(+), 25 deletions(-)
>> create mode 100644 drivers/mmc/host/sdhci-milbeaut.c
>> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.h
>>
>> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
>> index 28fcd8f..9b39111 100644
>> --- a/drivers/mmc/host/Kconfig
>> +++ b/drivers/mmc/host/Kconfig
>> @@ -353,6 +353,17 @@ config MMC_SDHCI_F_SDH30
>>
>> If unsure, say N.
>>
>> +config MMC_SDHCI_MILBEAUT
>> + tristate "SDHCI support for Socionext Milbeaut Serieas using F_SDH30"
>> + depends on MMC_SDHCI_PLTFM
>> + depends on OF
>> + help
>> + This selects the Secure Digital Host Controller Interface (SDHCI)
>> + Needed by Milbeaut SoC for MMC / SD / SDIO support.
>> + If you have a controller with this interface, say Y or M here.
>> +
>> + If unsure, say N.
>> +
>> config MMC_SDHCI_IPROC
>> tristate "SDHCI support for the BCM2835 & iProc SD/MMC Controller"
>> depends on ARCH_BCM2835 || ARCH_BCM_IPROC || COMPILE_TEST
>> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
>> index 7357871..db98e8a 100644
>> --- a/drivers/mmc/host/Makefile
>> +++ b/drivers/mmc/host/Makefile
>> @@ -21,6 +21,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o
>> obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
>> obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o
>> obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o
>> +obj-$(CONFIG_MMC_SDHCI_MILBEAUT) += sdhci-milbeaut.o
>> obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
>> obj-$(CONFIG_MMC_SDHCI_AM654) += sdhci_am654.o
>> obj-$(CONFIG_MMC_WBSD) += wbsd.o
>> diff --git a/drivers/mmc/host/sdhci-milbeaut.c b/drivers/mmc/host/sdhci-milbeaut.c
>> new file mode 100644
>> index 0000000..a1aa21b
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci-milbeaut.c
>> @@ -0,0 +1,362 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2013 - 2015 Fujitsu Semiconductor, Ltd
>> + * Vincent Yang <vincent.yang@xxxxxxxxxxxxxx>
>> + * Copyright (C) 2015 Linaro Ltd Andy Green <andy.green@xxxxxxxxxx>
>> + * Copyright (C) 2019 Socionext Inc.
>> + * Takao Orito <orito.takao@xxxxxxxxxxxxx>
>> + */
>> +
>> +#include <linux/bits.h>
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/err.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/property.h>
>> +
>> +#include "sdhci-pltfm.h"
>> +#include "sdhci_f_sdh30.h"
>> +
>> +/* milbeaut bridge controller register */
>> +#define MLB_SOFT_RESET 0x0200
>> +#define MLB_SOFT_RESET_RSTX BIT(0)
>> +
>> +#define MLB_WP_CD_LED_SET 0x0210
>> +#define MLB_WP_CD_LED_SET_LED_INV BIT(2)
>> +
>> +#define MLB_CR_SET 0x0220
>> +#define MLB_CR_SET_CR_TOCLKUNIT BIT(24)
>> +#define MLB_CR_SET_CR_TOCLKFREQ_SFT (16)
>> +#define MLB_CR_SET_CR_TOCLKFREQ_MASK (0x3F << MLB_CR_SET_CR_TOCLKFREQ_SFT)
>> +#define MLB_CR_SET_CR_BCLKFREQ_SFT (8)
>> +#define MLB_CR_SET_CR_BCLKFREQ_MASK (0xFF << MLB_CR_SET_CR_BCLKFREQ_SFT)
>> +#define MLB_CR_SET_CR_RTUNTIMER_SFT (4)
>> +#define MLB_CR_SET_CR_RTUNTIMER_MASK (0xF << MLB_CR_SET_CR_RTUNTIMER_SFT)
>> +
>> +#define MLB_SD_TOCLK_I_DIV 16
>> +#define MLB_TOCLKFREQ_UNIT_THRES 16000000
>> +#define MLB_CAL_TOCLKFREQ_MHZ(rate) (rate / MLB_SD_TOCLK_I_DIV / 1000000)
>> +#define MLB_CAL_TOCLKFREQ_KHZ(rate) (rate / MLB_SD_TOCLK_I_DIV / 1000)
>> +#define MLB_TOCLKFREQ_MAX 63
>> +#define MLB_TOCLKFREQ_MIN 1
>> +
>> +#define MLB_SD_BCLK_I_DIV 4
>> +#define MLB_CAL_BCLKFREQ(rate) (rate / MLB_SD_BCLK_I_DIV / 1000000)
>> +#define MLB_BCLKFREQ_MAX 255
>> +#define MLB_BCLKFREQ_MIN 1
>> +
>> +#define MLB_CDR_SET 0x0230
>> +#define MLB_CDR_SET_CLK2POW16 3
>> +
>> +struct f_sdhost_priv {
>> + struct clk *clk_iface;
>> + struct clk *clk;
>> + struct device *dev;
>> + bool enable_cmd_dat_delay;
>> +};
>> +
>> +static void sdhci_milbeaut_soft_voltage_switch(struct sdhci_host *host)
>> +{
>> + u32 ctrl = 0;
>> +
>> + usleep_range(2500, 3000);
>> + ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
>> + ctrl |= F_SDH30_CRES_O_DN;
>> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
>> + ctrl |= F_SDH30_MSEL_O_1_8;
>> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
>> +
>> + ctrl &= ~F_SDH30_CRES_O_DN;
>> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
>> + usleep_range(2500, 3000);
>> +
>> + ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING);
>> + ctrl |= F_SDH30_CMD_CHK_DIS;
>> + sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING);
>> +}
>> +
>> +static unsigned int sdhci_milbeaut_get_min_clock(struct sdhci_host *host)
>> +{
>> + return F_SDH30_MIN_CLOCK;
>> +}
>> +
>> +static void sdhci_milbeaut_reset(struct sdhci_host *host, u8 mask)
>> +{
>> + struct f_sdhost_priv *priv = sdhci_priv(host);
>> + u16 clk;
>> + u32 ctl;
>> + ktime_t timeout;
>> +
>> + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
>> + clk = (clk & ~SDHCI_CLOCK_CARD_EN) | SDHCI_CLOCK_INT_EN;
>> + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
>> +
>> + sdhci_reset(host, mask);
>> +
>> + clk |= SDHCI_CLOCK_CARD_EN;
>> + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
>> +
>> + timeout = ktime_add_ms(ktime_get(), 10);
>> + while (1) {
>> + bool timedout = ktime_after(ktime_get(), timeout);
>> +
>> + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
>> + if (clk & SDHCI_CLOCK_INT_STABLE)
>> + break;
>> + if (timedout) {
>> + pr_err("%s: Internal clock never stabilised.\n",
>> + mmc_hostname(host->mmc));
>> + sdhci_dumpregs(host);
>> + return;
>> + }
>> + udelay(10);
>> + }
>> +
>> + if (priv->enable_cmd_dat_delay) {
>> + ctl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
>> + ctl |= F_SDH30_CMD_DAT_DELAY;
>> + sdhci_writel(host, ctl, F_SDH30_ESD_CONTROL);
>> + }
>> +}
>> +
>> +static void sdhci_milbeaut_set_power(struct sdhci_host *host,
>> + unsigned char mode, unsigned short vdd)
>> +{
>> + if (!IS_ERR(host->mmc->supply.vmmc)) {
>> + struct mmc_host *mmc = host->mmc;
>> +
>> + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
>> + }
>> + sdhci_set_power_noreg(host, mode, vdd);
>> +}
>> +
>> +static const struct sdhci_ops sdhci_milbeaut_ops = {
>> + .voltage_switch = sdhci_milbeaut_soft_voltage_switch,
>> + .get_min_clock = sdhci_milbeaut_get_min_clock,
>> + .reset = sdhci_milbeaut_reset,
>> + .set_clock = sdhci_set_clock,
>> + .set_bus_width = sdhci_set_bus_width,
>> + .set_uhs_signaling = sdhci_set_uhs_signaling,
>> + .set_power = sdhci_milbeaut_set_power,
>> +};
>> +
>> +static void sdhci_milbeaut_bridge_reset(struct sdhci_host *host,
>> + int reset_flag)
>> +{
>> + if (reset_flag)
>> + sdhci_writel(host, 0, MLB_SOFT_RESET);
>> + else
>> + sdhci_writel(host, MLB_SOFT_RESET_RSTX, MLB_SOFT_RESET);
>> +}
>> +
>> +static void sdhci_milbeaut_bridge_init(struct sdhci_host *host,
>> + int rate)
>> +{
>> + u32 val, clk;
>> +
>> + /* IO_SDIO_CR_SET should be set while reset */
>> + val = sdhci_readl(host, MLB_CR_SET);
>> + val &= ~(MLB_CR_SET_CR_TOCLKFREQ_MASK | MLB_CR_SET_CR_TOCLKUNIT |
>> + MLB_CR_SET_CR_BCLKFREQ_MASK);
>> + if (rate >= MLB_TOCLKFREQ_UNIT_THRES) {
>> + clk = MLB_CAL_TOCLKFREQ_MHZ(rate);
>> + clk = min_t(u32, MLB_TOCLKFREQ_MAX, clk);
>> + val |= MLB_CR_SET_CR_TOCLKUNIT |
>> + (clk << MLB_CR_SET_CR_TOCLKFREQ_SFT);
>> + } else {
>> + clk = MLB_CAL_TOCLKFREQ_KHZ(rate);
>> + clk = min_t(u32, MLB_TOCLKFREQ_MAX, clk);
>> + clk = max_t(u32, MLB_TOCLKFREQ_MIN, clk);
>> + val |= clk << MLB_CR_SET_CR_TOCLKFREQ_SFT;
>> + }
>> +
>> + clk = MLB_CAL_BCLKFREQ(rate);
>> + clk = min_t(u32, MLB_BCLKFREQ_MAX, clk);
>> + clk = max_t(u32, MLB_BCLKFREQ_MIN, clk);
>> + val |= clk << MLB_CR_SET_CR_BCLKFREQ_SFT;
>> + val &= ~MLB_CR_SET_CR_RTUNTIMER_MASK;
>> + sdhci_writel(host, val, MLB_CR_SET);
>> +
>> + sdhci_writel(host, MLB_CDR_SET_CLK2POW16, MLB_CDR_SET);
>> +
>> + sdhci_writel(host, MLB_WP_CD_LED_SET_LED_INV, MLB_WP_CD_LED_SET);
>> +}
>> +
>> +static void sdhci_milbeaut_vendor_init(struct sdhci_host *host)
>> +{
>> + struct f_sdhost_priv *priv = sdhci_priv(host);
>> + u32 ctl;
>> +
>> + ctl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
>> + ctl |= F_SDH30_CRES_O_DN;
>> + sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
>> + ctl &= ~F_SDH30_MSEL_O_1_8;
>> + sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
>> + ctl &= ~F_SDH30_CRES_O_DN;
>> + sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
>> +
>> + ctl = sdhci_readw(host, F_SDH30_AHB_CONFIG);
>> + ctl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 |
>> + F_SDH30_AHB_INCR_4;
>> + ctl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN);
>> + sdhci_writew(host, ctl, F_SDH30_AHB_CONFIG);
>> +
>> + if (priv->enable_cmd_dat_delay) {
>> + ctl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
>> + ctl |= F_SDH30_CMD_DAT_DELAY;
>> + sdhci_writel(host, ctl, F_SDH30_ESD_CONTROL);
>> + }
>> +}
>> +
>> +static const struct of_device_id mlb_dt_ids[] = {
>> + {
>> + .compatible = "socionext,milbeaut-m10v-sdhci-3.0",
>> + },
>> + { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, mlb_dt_ids);
>> +
>> +static void sdhci_milbeaut_init(struct sdhci_host *host)
>> +{
>> + struct f_sdhost_priv *priv = sdhci_priv(host);
>> + int rate = clk_get_rate(priv->clk);
>> + u16 ctl;
>> +
>> + sdhci_milbeaut_bridge_reset(host, 0);
>> +
>> + ctl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
>> + ctl &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN);
>> + sdhci_writew(host, ctl, SDHCI_CLOCK_CONTROL);
>> +
>> + sdhci_milbeaut_bridge_reset(host, 1);
>> +
>> + sdhci_milbeaut_bridge_init(host, rate);
>> + sdhci_milbeaut_bridge_reset(host, 0);
>> +
>> + sdhci_milbeaut_vendor_init(host);
>> +}
>> +
>> +static int sdhci_milbeaut_probe(struct platform_device *pdev)
>> +{
>> + struct sdhci_host *host;
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + int irq, ret = 0;
>> + struct f_sdhost_priv *priv;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0) {
>> + dev_err(dev, "%s: no irq specified\n", __func__);
>> + return irq;
>> + }
>> +
>> + host = sdhci_alloc_host(dev, sizeof(struct f_sdhost_priv));
>> + if (IS_ERR(host))
>> + return PTR_ERR(host);
>> +
>> + priv = sdhci_priv(host);
>> + priv->dev = dev;
>> +
>> + host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
>> + SDHCI_QUIRK_INVERTED_WRITE_PROTECT |
>> + SDHCI_QUIRK_CLOCK_BEFORE_RESET |
>> + SDHCI_QUIRK_DELAY_AFTER_POWER;
>> + host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
>> + SDHCI_QUIRK2_TUNING_WORK_AROUND |
>> + SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
>> +
>> + priv->enable_cmd_dat_delay = device_property_read_bool(dev,
>> + "fujitsu,cmd-dat-delay-select");
>> +
>> + ret = mmc_of_parse(host->mmc);
>> + if (ret)
>> + goto err;
>> +
>> + platform_set_drvdata(pdev, host);
>> +
>> + host->hw_name = "f_sdh30";
>> + host->ops = &sdhci_milbeaut_ops;
>> + host->irq = irq;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + host->ioaddr = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(host->ioaddr)) {
>> + ret = PTR_ERR(host->ioaddr);
>> + goto err;
>> + }
>> +
>> + if (dev_of_node(dev)) {
>> + sdhci_get_of_property(pdev);
>> +
>> + priv->clk_iface = devm_clk_get(&pdev->dev, "iface");
>> + if (IS_ERR(priv->clk_iface)) {
>> + ret = PTR_ERR(priv->clk_iface);
>> + goto err;
>> + }
>> +
>> + ret = clk_prepare_enable(priv->clk_iface);
>> + if (ret)
>> + goto err;
>> +
>> + priv->clk = devm_clk_get(&pdev->dev, "core");
>> + if (IS_ERR(priv->clk)) {
>> + ret = PTR_ERR(priv->clk);
>> + goto err_clk;
>> + }
>> +
>> + ret = clk_prepare_enable(priv->clk);
>> + if (ret)
>> + goto err_clk;
>> + }
>> +
>> + sdhci_milbeaut_init(host);
>> +
>> + ret = sdhci_add_host(host);
>> + if (ret)
>> + goto err_add_host;
>> +
>> + return 0;
>> +
>> +err_add_host:
>> + clk_disable_unprepare(priv->clk);
>> +err_clk:
>> + clk_disable_unprepare(priv->clk_iface);
>> +err:
>> + sdhci_free_host(host);
>> + return ret;
>> +}
>> +
>> +static int sdhci_milbeaut_remove(struct platform_device *pdev)
>> +{
>> + struct sdhci_host *host = platform_get_drvdata(pdev);
>> + struct f_sdhost_priv *priv = sdhci_priv(host);
>> +
>> + sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
>> + 0xffffffff);
>> +
>> + clk_disable_unprepare(priv->clk_iface);
>> + clk_disable_unprepare(priv->clk);
>> +
>> + sdhci_free_host(host);
>> + platform_set_drvdata(pdev, NULL);
>> +
>> + return 0;
>> +}
>> +
>> +static struct platform_driver sdhci_milbeaut_driver = {
>> + .driver = {
>> + .name = "sdhci-milbeaut",
>> + .of_match_table = of_match_ptr(mlb_dt_ids),
>> + },
>> + .probe = sdhci_milbeaut_probe,
>> + .remove = sdhci_milbeaut_remove,
>> +};
>> +
>> +module_platform_driver(sdhci_milbeaut_driver);
>> +
>> +MODULE_DESCRIPTION("MILBEAUT SD Card Controller driver");
>> +MODULE_AUTHOR("Takao Orito <orito.takao@xxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_ALIAS("platform:sdhci-milbeaut");
>> diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c
>> index 485f759..ca4c99a 100644
>> --- a/drivers/mmc/host/sdhci_f_sdh30.c
>> +++ b/drivers/mmc/host/sdhci_f_sdh30.c
>> @@ -19,31 +19,7 @@
>> #include <linux/clk.h>
>>
>> #include "sdhci-pltfm.h"
>> -
>> -/* F_SDH30 extended Controller registers */
>> -#define F_SDH30_AHB_CONFIG 0x100
>> -#define F_SDH30_AHB_BIGED 0x00000040
>> -#define F_SDH30_BUSLOCK_DMA 0x00000020
>> -#define F_SDH30_BUSLOCK_EN 0x00000010
>> -#define F_SDH30_SIN 0x00000008
>> -#define F_SDH30_AHB_INCR_16 0x00000004
>> -#define F_SDH30_AHB_INCR_8 0x00000002
>> -#define F_SDH30_AHB_INCR_4 0x00000001
>> -
>> -#define F_SDH30_TUNING_SETTING 0x108
>> -#define F_SDH30_CMD_CHK_DIS 0x00010000
>> -
>> -#define F_SDH30_IO_CONTROL2 0x114
>> -#define F_SDH30_CRES_O_DN 0x00080000
>> -#define F_SDH30_MSEL_O_1_8 0x00040000
>> -
>> -#define F_SDH30_ESD_CONTROL 0x124
>> -#define F_SDH30_EMMC_RST 0x00000002
>> -#define F_SDH30_EMMC_HS200 0x01000000
>> -
>> -#define F_SDH30_CMD_DAT_DELAY 0x200
>> -
>> -#define F_SDH30_MIN_CLOCK 400000
>> +#include "sdhci_f_sdh30.h"
>>
>> struct f_sdhost_priv {
>> struct clk *clk_iface;
>> diff --git a/drivers/mmc/host/sdhci_f_sdh30.h b/drivers/mmc/host/sdhci_f_sdh30.h
>> new file mode 100644
>> index 0000000..fc1ad28
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci_f_sdh30.h
>> @@ -0,0 +1,32 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (C) 2013 - 2015 Fujitsu Semiconductor, Ltd
>> + * Vincent Yang <vincent.yang@xxxxxxxxxxxxxx>
>> + * Copyright (C) 2015 Linaro Ltd Andy Green <andy.green@xxxxxxxxxx>
>> + * Copyright (C) 2019 Socionext Inc.
>> + *
>> + */
>> +
>> +/* F_SDH30 extended Controller registers */
>> +#define F_SDH30_AHB_CONFIG 0x100
>> +#define F_SDH30_AHB_BIGED BIT(6)
>> +#define F_SDH30_BUSLOCK_DMA BIT(5)
>> +#define F_SDH30_BUSLOCK_EN BIT(4)
>> +#define F_SDH30_SIN BIT(3)
>> +#define F_SDH30_AHB_INCR_16 BIT(2)
>> +#define F_SDH30_AHB_INCR_8 BIT(1)
>> +#define F_SDH30_AHB_INCR_4 BIT(0)
>> +
>> +#define F_SDH30_TUNING_SETTING 0x108
>> +#define F_SDH30_CMD_CHK_DIS BIT(16)
>> +
>> +#define F_SDH30_IO_CONTROL2 0x114
>> +#define F_SDH30_CRES_O_DN BIT(19)
>> +#define F_SDH30_MSEL_O_1_8 BIT(18)
>> +
>> +#define F_SDH30_ESD_CONTROL 0x124
>> +#define F_SDH30_EMMC_RST BIT(1)
>> +#define F_SDH30_CMD_DAT_DELAY BIT(9)
>> +#define F_SDH30_EMMC_HS200 BIT(24)
>> +
>> +#define F_SDH30_MIN_CLOCK 400000
>> --
>> 1.9.1
>>
>>
>
