This patch set is based on renesas-drivers.git / renesas-drivers-2019-05-21-v5.2-rc1 tag. Since SDHI host internal DMAC of the R-Car Gen3 cannot handle two or more segments, the performance rate (especially, eMMC HS400 reading) is not good. However, if IOMMU is enabled on the DMAC, since IOMMU will map multiple scatter gather buffers as one contignous iova, the DMAC can handle the iova as well and then the performance rate is possible to improve. In fact, I have measured the performance by using bonnie++, "Sequential Input - block" rate was improved on r8a7795. Please refer to the end of this email about the performance. (I beleive if the performance is improved, the CPU load is also increased.) However, in case of a sdio card (especiialy some WiFi cards/drivers), scatter gather buffers are possible to be not contiguous iova because each scatter gather buffer has only about 1500 bytes, the DMAC cannot handle it. So, this patch set adds init_card() ops to detect the card type, and then the driver changes the max_segs if the DMAC is under IOMMU environment and an sd card/mmc is detected. Remarks: I mentioned that Gen2 with the SYS-DMAC basis environment can also improve the perfomance on the public ML [1], but there was a measurement error so that I didn't make a patch for SYS-DMAC. Changes from v2 [2]: - Add some conditions in the init_card(). - Add a comment in the init_card(). - Add definitions for some "MAX_SEGS". Changes from v1 [3]: - Remove adding init_card ops into struct tmio_mmc_dma_ops and tmio_mmc_host and just set init_card on renesas_sdhi_core.c. - Revise typos on "mmc: tmio: No memory size limitation if runs on IOMMU". - Add Simon-san's Reviewed-by on a tmio patch. [1] https://patchwork.kernel.org/patch/10940225/#22635487 [2] https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=116729 [3] https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=110485 --- kernel v5.2-rc1 + local patches + HS400,,,,,,,,,,,,,,,,,,,,,,,,,, Buildroot 2019.02.1,,,,,,,,,,,,,,,,,,,,,,,,,, Bonnie++ 1.03e : bonnie\+\+ -d ./ -s 8192 -r 4096 -b -u root,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,, environment,Size,Sequential Output - per char (K/sec),<- (CPU %),Sequential Output - block (K/sec),<- (CPU %),Sequential Output - rewrite (K/sec),<- (CPU %),Sequential Input - per char (K/sec),<- (CPU %),Sequential Input ? block (K/sec),<- (CPU %),Random seeks,<- (CPU %),files,Sequential Create,<- (CPU %),Sequential Read,<- (CPU %),Sequential Delete,<- (CPU %),Random Create,<- (CPU %),Random Read,<- (CPU %),Random Delete,<- (CPU %) H3_max_segs_1_on_IOMMU,8G,80858,96,121466,28,60602,16,71712,95,121427,15,4128.5,11,16,678,3,+++++,+++,593,2,616,3,+++++,+++,603,3 H3_max_segs_512_on_IOMMU,8G,76637,91,132994,31,81478,20,74522,98,197325,26,4526.5,12,16,864,4,+++++,+++,821,4,814,4,+++++,+++,786,4 --- Yoshihiro Shimoda (3): mmc: tmio: No memory size limitation if runs on IOMMU mmc: tmio: Add a definition for default max_segs mmc: renesas_sdhi: use multiple segments if possible drivers/mmc/host/renesas_sdhi_core.c | 25 +++++++++++++++++++++++++ drivers/mmc/host/tmio_mmc.h | 1 + drivers/mmc/host/tmio_mmc_core.c | 7 ++++--- 3 files changed, 30 insertions(+), 3 deletions(-) -- 2.7.4
