Re: [PATCH v2] mmc: core: retry CMD1 in mmc_send_op_cond() even if the ocr = 0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 9 Apr 2019 at 13:09, Yoshihiro Shimoda
<yoshihiro.shimoda.uh@xxxxxxxxxxx> wrote:
>
> According to eMMC specification v5.1 section 6.4.3, we should issue
> CMD1 repeatedly in the idle state until the eMMC is ready even if
> the mmc_attach_mmc() calls this function with ocr = 0. Otherwise
> some eMMC devices seems to enter the inactive mode after
> mmc_init_card() issued CMD0 when the eMMC device is busy.
>
> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>

Applied for next, thanks!

Let's get some test coverage of this before we decide if this a
material for stable.

Kind regards
Uffe


> ---
>  Changes from v1 (https://patchwork.kernel.org/patch/10874619/):
>  - Revise the comment on the source code.
>
>  We can reproduce this issue if:
>   - we add no-sd and no-sdio property into sdhi2 node of salvator-common.dtsi,
>   - the renesas_sdhi driver is kernel module,
>   - Using a Salvator-XS board that has Samsung eMMC device,
>   - enter suspend and exit it,
>   - and then insmod renesas_sdhi_{core,internal_dmac}.ko.
>
>  After that, the following error happened and any partitions are not detected.
>   mmc1: error -110 whilst initialising MMC card
>
>  I tested this patch on:
>   - M3-N Salvator-XS with a Samsung eMMC device,
>   - M3-W Salvator-X with SiliconMotion eMMC device,
>   - and M3-W Starter Kit with Micron eMMC device.
>
>  drivers/mmc/core/mmc_ops.c | 16 +++++++++++-----
>  1 file changed, 11 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> index c5208fb..a533cab 100644
> --- a/drivers/mmc/core/mmc_ops.c
> +++ b/drivers/mmc/core/mmc_ops.c
> @@ -184,11 +184,7 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
>                 if (err)
>                         break;
>
> -               /* if we're just probing, do a single pass */
> -               if (ocr == 0)
> -                       break;
> -
> -               /* otherwise wait until reset completes */
> +               /* wait until reset completes */
>                 if (mmc_host_is_spi(host)) {
>                         if (!(cmd.resp[0] & R1_SPI_IDLE))
>                                 break;
> @@ -200,6 +196,16 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
>                 err = -ETIMEDOUT;
>
>                 mmc_delay(10);
> +
> +               /*
> +                * According to eMMC specification v5.1 section 6.4.3, we
> +                * should issue CMD1 repeatedly in the idle state until
> +                * the eMMC is ready. Otherwise some eMMC devices seem to enter
> +                * the inactive mode after mmc_init_card() issued CMD0 when
> +                * the eMMC device is busy.
> +                */
> +               if (!ocr && !mmc_host_is_spi(host))
> +                       cmd.arg = cmd.resp[0] | BIT(30);
>         }
>
>         if (rocr && !mmc_host_is_spi(host))
> --
> 2.7.4
>



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux