Re: [PATCH v2] mmc: sdhci_am654: Clear HISPD_ENA in some lower speed modes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 1 Apr 2019 at 14:58, Faiz Abbas <faiz_abbas@xxxxxx> wrote:
>
> According to the AM654x Data Manual[1], the setup timing in lower speed
> modes can only be met if the controller uses a falling edge data launch.
>
> To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
> cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
> speed modes.
>
> Use the sdhci writeb callback to implement this condition.
>
> [1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1
>
> Signed-off-by: Faiz Abbas <faiz_abbas@xxxxxx>

Applied for next, thanks!

Kind regards
Uffe


> ---
>
> v2: Dropped QUIRK in favour of writeb callback
>
>  drivers/mmc/host/Kconfig       |  1 +
>  drivers/mmc/host/sdhci_am654.c | 22 ++++++++++++++++++++++
>  2 files changed, 23 insertions(+)
>
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 28fcd8f580a1..6379fba8b122 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -993,6 +993,7 @@ config MMC_SDHCI_OMAP
>  config MMC_SDHCI_AM654
>         tristate "Support for the SDHCI Controller in TI's AM654 SOCs"
>         depends on MMC_SDHCI_PLTFM && OF
> +       select MMC_SDHCI_IO_ACCESSORS
>         help
>           This selects the Secure Digital Host Controller Interface (SDHCI)
>           support present in TI's AM654 SOCs. The controller supports
> diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
> index eea183e90f1b..a91c0b45c48d 100644
> --- a/drivers/mmc/host/sdhci_am654.c
> +++ b/drivers/mmc/host/sdhci_am654.c
> @@ -158,6 +158,27 @@ static void sdhci_am654_set_power(struct sdhci_host *host, unsigned char mode,
>         sdhci_set_power_noreg(host, mode, vdd);
>  }
>
> +static void sdhci_am654_write_b(struct sdhci_host *host, u8 val, int reg)
> +{
> +       unsigned char timing = host->mmc->ios.timing;
> +
> +       if (reg == SDHCI_HOST_CONTROL) {
> +               switch (timing) {
> +               /*
> +                * According to the data manual, HISPD bit
> +                * should not be set in these speed modes.
> +                */
> +               case MMC_TIMING_SD_HS:
> +               case MMC_TIMING_MMC_HS:
> +               case MMC_TIMING_UHS_SDR12:
> +               case MMC_TIMING_UHS_SDR25:
> +                       val &= ~SDHCI_CTRL_HISPD;
> +               }
> +       }
> +
> +       writeb(val, host->ioaddr + reg);
> +}
> +
>  static struct sdhci_ops sdhci_am654_ops = {
>         .get_max_clock = sdhci_pltfm_clk_get_max_clock,
>         .get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
> @@ -165,6 +186,7 @@ static struct sdhci_ops sdhci_am654_ops = {
>         .set_bus_width = sdhci_set_bus_width,
>         .set_power = sdhci_am654_set_power,
>         .set_clock = sdhci_am654_set_clock,
> +       .write_b = sdhci_am654_write_b,
>         .reset = sdhci_reset,
>  };
>
> --
> 2.19.2
>



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux