On 27/03/19 1:47 PM, Faiz Abbas wrote:
> Hi Adrian,
>
> On 27/03/19 4:45 PM, Adrian Hunter wrote:
>> On 26/03/19 1:00 PM, Faiz Abbas wrote:
>>> commit 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset
>>> callback") skips data resets during tuning operation. Because of this,
>>> a data error or data finish interrupt might still arrive after a command
>>> error has been handled and the mrq ended. This ends up with a "mmc0: Got
>>> data interrupt 0x00000002 even though no data operation was in progress"
>>> error message.
>>>
>>> Fix this by adding a platform specific callback for sdhci_irq. Mark the
>>> mrq as a failure but wait for a data interrupt instead of calling
>>> finish_mrq().
>>>
>>> Signed-off-by: Faiz Abbas <faiz_abbas@xxxxxx>
>>> ---
>>> drivers/mmc/host/sdhci-omap.c | 37 +++++++++++++++++++++++++++++++++++
>>> 1 file changed, 37 insertions(+)
>>>
>>> diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
>>> index 5bbed477c9b1..9da2ff9ede8b 100644
>>> --- a/drivers/mmc/host/sdhci-omap.c
>>> +++ b/drivers/mmc/host/sdhci-omap.c
>>> @@ -797,6 +797,42 @@ void sdhci_omap_reset(struct sdhci_host *host, u8 mask)
>>> sdhci_reset(host, mask);
>>> }
>>>
>>> +#define CMD_ERR_MASK (SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX |\
>>> + SDHCI_INT_TIMEOUT)
>>> +#define CMD_MASK (CMD_ERR_MASK | SDHCI_INT_RESPONSE)
>>> +
>>> +static irqreturn_t sdhci_omap_irq(struct sdhci_host *host, u32 intmask)
>>> +{
>>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>> + struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
>>> +
>>> + if (omap_host->is_tuning && (intmask & CMD_ERR_MASK)) {
>>> +
>>> + /*
>>> + * Since we are not resetting data lines during tuning
>>> + * operation, data error or data complete interrupts
>>> + * might still arrive. Mark this request as a failure
>>> + * but still wait for the data interrupt
>>> + */
>>> + if (intmask & SDHCI_INT_TIMEOUT)
>>> + host->cmd->error = -ETIMEDOUT;
>>> + else
>>> + host->cmd->error = -EILSEQ;
>>> +
>>> + sdhci_finish_command(host);
>>
>> Would it be possible to set SDHCI_INT_RESPONSE instead of calling
>> sdhci_finish_command() directly?
>>
>
> It should be possible. But what we are trying to do won't be very clear
> from the code. Ideally an interrupt handler should not set any interrupt
> bits, just handle and clear them. Also, setting the RESPONSE bit even
> when there has been no response seems wrong and makes the code more
> convoluted.
Well, I am not in favour of exporting sdhci_finish_command().
So I had a look and it is not obvious why you need to call it.
What about something this:
if (omap_host->is_tuning && host->cmd && !host->data_early &&
(intmask & CMD_ERR_MASK)) {
if (intmask & SDHCI_INT_TIMEOUT)
host->cmd->error = -ETIMEDOUT;
else
host->cmd->error = -EILSEQ;
host->cmd = NULL;
sdhci_writel(host, intmask & CMD_MASK, SDHCI_INT_STATUS);
intmask &= ~CMD_MASK;
}
