On Mon, 4 Mar 2019 at 11:17, Ludovic Barre <ludovic.Barre@xxxxxx> wrote:
>
> From: Ludovic Barre <ludovic.barre@xxxxxx>
>
> This patch defines get_dctrl_cfg callback for sdmmc variant.
> sdmmc variant has specific stm32 transfer modes.
> sdmmc data transfer mode selection could be:
> -Block data transfer ending on block count.
> -SDIO multibyte data transfer.
> -MMC Stream data transfer (not used).
> -Block data transfer ending with STOP_TRANSMISSION command.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@xxxxxx>
> ---
> drivers/mmc/host/mmci.h | 5 +++++
> drivers/mmc/host/mmci_stm32_sdmmc.c | 21 +++++++++++++++++++++
> 2 files changed, 26 insertions(+)
>
> diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
> index 6f28f71..eb5d99af 100644
> --- a/drivers/mmc/host/mmci.h
> +++ b/drivers/mmc/host/mmci.h
> @@ -131,6 +131,11 @@
> /* Control register extensions in the Qualcomm versions */
> #define MCI_DPSM_QCOM_DATA_PEND BIT(17)
> #define MCI_DPSM_QCOM_RX_DATA_PEND BIT(20)
> +/* Control register extensions in STM32 versions */
> +#define MCI_DPSM_STM32_MODE_BLOCK (0 << 2)
> +#define MCI_DPSM_STM32_MODE_SDIO (1 << 2)
> +#define MCI_DPSM_STM32_MODE_STREAM (2 << 2)
> +#define MCI_DPSM_STM32_MODE_BLOCK_STOP (3 << 2)
>
> #define MMCIDATACNT 0x030
> #define MMCISTATUS 0x034
> diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
> index cfbfc6f..e7bf744 100644
> --- a/drivers/mmc/host/mmci_stm32_sdmmc.c
> +++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
> @@ -265,10 +265,31 @@ static void mmci_sdmmc_set_pwrreg(struct mmci_host *host, unsigned int pwr)
> }
> }
>
> +u32 sdmmc_get_dctrl_cfg(struct mmci_host *host)
> +{
> + struct variant_data *variant = host->variant;
> + int blksz_bits;
> + u32 datactrl;
> +
> + blksz_bits = ffs(host->data->blksz) - 1;
> + datactrl = variant->datactrl_dpsm_enable | blksz_bits << 4;
> +
> + if (host->mmc->card && mmc_card_sdio(host->mmc->card) &&
> + host->data->blocks == 1)
These settings are not limited to deal with the block size bits.
Don't get me wrong, it seems reasonable to include them, but the
generic code in mmci_start_data() also have code to cope with SDIO. I
think we should start by splitting that up into a couple of
helper/library functions, and make the legacy variant to use them.
This should probably be done as a preparation to your series, so you
can build on top of that.
Does it make sense? If not, please tell and I can try to provide some
patch to show you what I mean.
> + datactrl |= MCI_DPSM_STM32_MODE_SDIO;
> + else if (host->data->stop && !host->mrq->sbc)
> + datactrl |= MCI_DPSM_STM32_MODE_BLOCK_STOP;
> + else
> + datactrl |= MCI_DPSM_STM32_MODE_BLOCK;
> +
> + return datactrl;
> +}
> +
> static struct mmci_host_ops sdmmc_variant_ops = {
> .validate_data = sdmmc_idma_validate_data,
> .prep_data = sdmmc_idma_prep_data,
> .unprep_data = sdmmc_idma_unprep_data,
> + .get_datactrl_cfg = sdmmc_get_dctrl_cfg,
> .dma_setup = sdmmc_idma_setup,
> .dma_start = sdmmc_idma_start,
> .dma_finalize = sdmmc_idma_finalize,
> --
> 2.7.4
>
Kind regards
Uffe
