Switch the SPI MMC driver to use GPIO descriptors internally
and just look those up using the standard slot GPIO
functions mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Make sure to request index 0 and 1 in accordance with the
SPI MMC DT binding, and add the same GPIOs in machine
descriptor tables on all boards that use SPI MMC in
board files.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, but this will be ignored by the MMC slot
GPIO code that uses the *raw accessors and rely on the
caps2 flags MMC_CAP2_CD_ACTIVE_HIGH and
MMC_CAP2_RO_ACTIVE_HIGH for polarity inversion semantics
as of now.
Cc: Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx> # Vision EP9307
Cc: Kuninori Morimoto <kuninori.morimoto.gx@xxxxxxxxxxx>
Cc: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v1->v3:
- Resending on top of the applied patches.
- Hartley: it'd be great if you could test this series
on the Vision EP9307.
- Kuninori/Laurent: hope one of you has this Ecovec board
so you can test it too.
---
arch/arm/mach-ep93xx/simone.c | 14 +++++++++---
arch/arm/mach-ep93xx/vision_ep9307.c | 17 ++++++++++----
arch/sh/boards/mach-ecovec24/setup.c | 17 +++++++++++---
drivers/mmc/host/mmc_spi.c | 27 ++++++++++++----------
drivers/mmc/host/of_mmc_spi.c | 34 ----------------------------
include/linux/spi/mmc_spi.h | 15 ------------
6 files changed, 53 insertions(+), 71 deletions(-)
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
index 41aa57581356..80ccb984d521 100644
--- a/arch/arm/mach-ep93xx/simone.c
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -25,6 +25,7 @@
#include <linux/platform_data/video-ep93xx.h>
#include <linux/platform_data/spi-ep93xx.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <mach/hardware.h>
#include <mach/gpio-ep93xx.h>
@@ -45,9 +46,15 @@ static struct ep93xxfb_mach_info __initdata simone_fb_info = {
static struct mmc_spi_platform_data simone_mmc_spi_data = {
.detect_delay = 500,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .flags = MMC_SPI_USE_CD_GPIO,
- .cd_gpio = EP93XX_GPIO_LINE_EGPIO0,
- .cd_debounce = 1,
+};
+
+static struct gpiod_lookup_table simone_mmc_spi_gpio_table = {
+ .dev_id = "mmc_spi.0", /* "mmc_spi" @ CS0 */
+ .table = {
+ /* Card detect */
+ GPIO_LOOKUP_IDX("A", 0, NULL, 0, GPIO_ACTIVE_LOW),
+ { },
+ },
};
static struct spi_board_info simone_spi_devices[] __initdata = {
@@ -105,6 +112,7 @@ static void __init simone_init_machine(void)
ep93xx_register_fb(&simone_fb_info);
ep93xx_register_i2c(simone_i2c_board_info,
ARRAY_SIZE(simone_i2c_board_info));
+ gpiod_add_lookup_table(&simone_mmc_spi_gpio_table);
ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
ARRAY_SIZE(simone_spi_devices));
simone_register_audio();
diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c
index 5a0b6187990a..767ee64628dc 100644
--- a/arch/arm/mach-ep93xx/vision_ep9307.c
+++ b/arch/arm/mach-ep93xx/vision_ep9307.c
@@ -18,6 +18,7 @@
#include <linux/platform_device.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/fb.h>
#include <linux/io.h>
#include <linux/mtd/partitions.h>
@@ -202,13 +203,20 @@ static struct mmc_spi_platform_data vision_spi_mmc_data = {
.detect_delay = 100,
.powerup_msecs = 100,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO,
- .cd_gpio = EP93XX_GPIO_LINE_EGPIO15,
- .cd_debounce = 1,
- .ro_gpio = EP93XX_GPIO_LINE_F(0),
.caps2 = MMC_CAP2_RO_ACTIVE_HIGH,
};
+static struct gpiod_lookup_table vision_spi_mmc_gpio_table = {
+ .dev_id = "mmc_spi.2", /* "mmc_spi @ CS2 */
+ .table = {
+ /* Card detect */
+ GPIO_LOOKUP_IDX("B", 7, NULL, 0, GPIO_ACTIVE_LOW),
+ /* Write protect */
+ GPIO_LOOKUP_IDX("F", 0, NULL, 1, GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
/*************************************************************************
* SPI Bus
*************************************************************************/
@@ -286,6 +294,7 @@ static void __init vision_init_machine(void)
ep93xx_register_i2c(vision_i2c_info,
ARRAY_SIZE(vision_i2c_info));
+ gpiod_add_lookup_table(&vision_spi_mmc_gpio_table);
ep93xx_register_spi(&vision_spi_master, vision_spi_board_info,
ARRAY_SIZE(vision_spi_board_info));
vision_register_i2s();
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index 06a894526a0b..3097307b7cb7 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -776,9 +776,19 @@ static struct mmc_spi_platform_data mmc_spi_info = {
.caps2 = MMC_CAP2_RO_ACTIVE_HIGH,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* 3.3V only */
.setpower = mmc_spi_setpower,
- .flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO,
- .cd_gpio = GPIO_PTY7,
- .ro_gpio = GPIO_PTY6,
+};
+
+static struct gpiod_lookup_table mmc_spi_gpio_table = {
+ .dev_id = "mmc_spi.0", /* device "mmc_spi" @ CS0 */
+ .table = {
+ /* Card detect */
+ GPIO_LOOKUP_IDX("sh7724_pfc", GPIO_PTY7, NULL, 0,
+ GPIO_ACTIVE_LOW),
+ /* Write protect */
+ GPIO_LOOKUP_IDX("sh7724_pfc", GPIO_PTY6, NULL, 1,
+ GPIO_ACTIVE_HIGH),
+ { },
+ },
};
static struct spi_board_info spi_bus[] = {
@@ -1282,6 +1292,7 @@ static int __init arch_setup(void)
gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */
gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */
+ gpiod_add_lookup_table(&mmc_spi_gpio_table);
spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus));
#endif
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index 476e53d30128..10ba46b728e8 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -1434,13 +1434,16 @@ static int mmc_spi_probe(struct spi_device *spi)
if (status != 0)
goto fail_add_host;
- if (host->pdata && host->pdata->flags & MMC_SPI_USE_CD_GPIO) {
- status = mmc_gpio_request_cd(mmc, host->pdata->cd_gpio,
- host->pdata->cd_debounce);
- if (status != 0)
- goto fail_add_host;
-
- /* The platform has a CD GPIO signal that may support
+ /*
+ * Index 0 is card detect
+ * Old boardfiles were specifying 1 ms as debounce
+ */
+ status = mmc_gpiod_request_cd(mmc, NULL, 0, false, 1, NULL);
+ if (status == -EPROBE_DEFER)
+ goto fail_add_host;
+ if (!status) {
+ /*
+ * The platform has a CD GPIO signal that may support
* interrupts, so let mmc_gpiod_request_cd_irq() decide
* if polling is needed or not.
*/
@@ -1448,12 +1451,12 @@ static int mmc_spi_probe(struct spi_device *spi)
mmc_gpiod_request_cd_irq(mmc);
}
- if (host->pdata && host->pdata->flags & MMC_SPI_USE_RO_GPIO) {
+ /* Index 1 is write protect/read only */
+ status = mmc_gpiod_request_ro(mmc, NULL, 1, false, 0, NULL);
+ if (status == -EPROBE_DEFER)
+ goto fail_add_host;
+ if (!status)
has_ro = true;
- status = mmc_gpio_request_ro(mmc, host->pdata->ro_gpio);
- if (status != 0)
- goto fail_add_host;
- }
dev_info(&spi->dev, "SD/MMC host %s%s%s%s%s\n",
dev_name(&mmc->class_dev),
diff --git a/drivers/mmc/host/of_mmc_spi.c b/drivers/mmc/host/of_mmc_spi.c
index c9eed8436b6b..b294b221f225 100644
--- a/drivers/mmc/host/of_mmc_spi.c
+++ b/drivers/mmc/host/of_mmc_spi.c
@@ -16,9 +16,7 @@
#include <linux/device.h>
#include <linux/slab.h>
#include <linux/irq.h>
-#include <linux/gpio.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/of_irq.h>
#include <linux/spi/spi.h>
#include <linux/spi/mmc_spi.h>
@@ -32,15 +30,7 @@
MODULE_LICENSE("GPL");
-enum {
- CD_GPIO = 0,
- WP_GPIO,
- NUM_GPIOS,
-};
-
struct of_mmc_spi {
- int gpios[NUM_GPIOS];
- bool alow_gpios[NUM_GPIOS];
int detect_irq;
struct mmc_spi_platform_data pdata;
};
@@ -102,30 +92,6 @@ struct mmc_spi_platform_data *mmc_spi_get_pdata(struct spi_device *spi)
oms->pdata.ocr_mask |= mask;
}
- for (i = 0; i < ARRAY_SIZE(oms->gpios); i++) {
- enum of_gpio_flags gpio_flags;
-
- oms->gpios[i] = of_get_gpio_flags(np, i, &gpio_flags);
- if (!gpio_is_valid(oms->gpios[i]))
- continue;
-
- if (gpio_flags & OF_GPIO_ACTIVE_LOW)
- oms->alow_gpios[i] = true;
- }
-
- if (gpio_is_valid(oms->gpios[CD_GPIO])) {
- oms->pdata.cd_gpio = oms->gpios[CD_GPIO];
- oms->pdata.flags |= MMC_SPI_USE_CD_GPIO;
- if (!oms->alow_gpios[CD_GPIO])
- oms->pdata.caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
- }
- if (gpio_is_valid(oms->gpios[WP_GPIO])) {
- oms->pdata.ro_gpio = oms->gpios[WP_GPIO];
- oms->pdata.flags |= MMC_SPI_USE_RO_GPIO;
- if (!oms->alow_gpios[WP_GPIO])
- oms->pdata.caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
- }
-
oms->detect_irq = irq_of_parse_and_map(np, 0);
if (oms->detect_irq != 0) {
oms->pdata.init = of_mmc_spi_init;
diff --git a/include/linux/spi/mmc_spi.h b/include/linux/spi/mmc_spi.h
index bfde741a543d..778ae8eb1f3e 100644
--- a/include/linux/spi/mmc_spi.h
+++ b/include/linux/spi/mmc_spi.h
@@ -8,11 +8,6 @@
struct device;
struct mmc_host;
-#define MMC_SPI_USE_CD_GPIO (1 << 0)
-#define MMC_SPI_USE_RO_GPIO (1 << 1)
-#define MMC_SPI_CD_GPIO_ACTIVE_LOW (1 << 2)
-#define MMC_SPI_RO_GPIO_ACTIVE_LOW (1 << 3)
-
/* Put this in platform_data of a device being used to manage an MMC/SD
* card slot. (Modeled after PXA mmc glue; see that for usage examples.)
*
@@ -27,16 +22,6 @@ struct mmc_spi_platform_data {
void *);
void (*exit)(struct device *, void *);
- /*
- * Card Detect and Read Only GPIOs. To enable debouncing on the card
- * detect GPIO, set the cd_debounce to the debounce time in
- * microseconds.
- */
- unsigned int flags;
- unsigned int cd_gpio;
- unsigned int cd_debounce;
- unsigned int ro_gpio;
-
/* Capabilities to pass into mmc core (e.g. MMC_CAP_NEEDS_POLL). */
unsigned long caps;
unsigned long caps2;
--
2.19.1
