Hi Andy,
On Wed, Oct 24, 2018 at 3:02 AM Andy Shevchenko
<andy.shevchenko@xxxxxxxxx> wrote:
>
> On Mon, Oct 22, 2018 at 04:34:55PM -0700, Rajat Jain wrote:
> > On Fri, Oct 19, 2018 at 2:13 AM Andy Shevchenko
> > <andy.shevchenko@xxxxxxxxx> wrote:
> > > On Fri, Oct 19, 2018 at 12:53 AM Rajat Jain <rajatja@xxxxxxxxxx> wrote:
>
> > > > across other users of this API (other MMC host controller drivers).
> > >
> > > > if (slot->cd_idx >= 0) {
> > > > - ret = mmc_gpiod_request_cd(host->mmc, NULL, slot->cd_idx,
> > > > + ret = mmc_gpiod_request_cd(host->mmc, "cd", slot->cd_idx,
> > > > slot->cd_override_level, 0, NULL);
> > >
> > > Yes.
> > >
> > > > + if (ret && ret != -EPROBE_DEFER)
> > > > + ret = mmc_gpiod_request_cd(host->mmc, NULL,
> > > > + slot->cd_idx,
> > > > + slot->cd_override_level,
> > > > + 0, NULL);
> > >
> > > And no. Instead of this part you need to provide an ACPI GPIO mapping table.
> >
> > Sure, I am willing to do so, and I tried earlier too. However, certain
> > doubts arose in my mind when I tried that and I posted my questions
> > earlier (https://lkml.org/lkml/2018/9/28/507) but couldn't elicit any
> > response. Unfortunately I still do not have answers. My primary
> > questions are:
> >
> > 1) - It seems that 1 SDHCI device may support multiple slots (looking
> > at the code). It is not clear to me if they could share card detect
> > interrupts, or should have separate ones?
>
> This is more likely question to HW engineers of your platform with a caveat
> that there should be a way to distinguish exact slot in which card is being
> inserted.
>
> > Also, the driver may not
> > really know?
>
> I think in such case the bug in HW design and / or driver.
Why? You can have a shared or dedicated interrupt and the driver does
not really need to know if it can poll the status.
>
> > So should I add 1 or two pins using the
> > devm_acpi_dev_add_driver_gpios().
>
> This depends on the above, e.g. HW design, ACPI tables.
Yes, it depends on the HW design and that is exactly why the approach
with devm_acpi_dev_add_driver_gpios() does not work well here: this is
a generic driver used on many platforms and you are trying to put the
platform knowledge into the driver. Here we are lucky I guess as I do
not believe anyone is using more than one slot, so we can have a tavle
with a single entry, but actually doing the fallback the way Rajat was
proposing is more correct. Or you have a table with N entries, where N
is hopefully sufficiently large.
>
>
> > Is some one familiar with SDHC
> > driver can answer these questions, it shall be great.
>
> Actually above questions better to ask in linux-mmc mailing list, which by the
> fact is in Cc list already. So, wait for someone to clarify.
>
>
> > 2) I'm not really sure what should I set "active_low" to? Isn't this
> > something that should be specified by platform / ACPI too, and driver
> > should just be able to say say choose whatever the ACPI says?
> >
> > struct acpi_gpio_params {
> > unsigned int crs_entry_index;
> > unsigned int line_index;
> > bool active_low;
> > };
>
>
> ACPI specification misses this property, that's why we have it in the
> structure. In your case it should be provided by _DSD and thus be consistent
> with the hardcoded values.
Again, you think as if the driver was platform specific; it is not. I
have 1000s of systems with different ACPI tables. Let's say half of
them use one polarity, and half another. Which polarity do you propose
to use?
Thanks.
--
Dmitry
