Re: [PATCH RFC 2/7] mmc: core: devfreq: Add devfreq based clock scaling support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

On 7/20/2018 8:54 PM, Rob Herring wrote:
On Fri, Jul 13, 2018 at 03:22:58PM +0530, Sayali Lokhande wrote:
This change adds the use of devfreq to MMC.
Both eMMC and SD card will use it.
For some workloads, such as video playback, it isn't
necessary for these cards to run at high speed.
Running at lower frequency, for example 52MHz, in such
cases can still meet the deadlines for data transfers.
Scaling down the clock frequency dynamically has power
savings not only because the bus is running at lower frequency
but also has an advantage of scaling down the system core
voltage, if supported.
Provide an ondemand clock scaling support similar to the
cpufreq ondemand governor having two thresholds,
up_threshold and down_threshold to decide whether to
increase the frequency or scale it down respectively.
The sampling interval is in the order of milliseconds.
If sampling interval is too low, frequent switching of
frequencies can lead to high power consumption and if
sampling interval is too high, the clock scaling logic
would take long time to realize that the underlying
hardware (controller and card) is busy and scale up
the clocks.

Signed-off-by: Talel Shenhar <tatias@xxxxxxxxxxxxxx>
Signed-off-by: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>
---
  .../devicetree/bindings/mmc/sdhci-msm.txt          |  10 +
  drivers/mmc/core/core.c                            | 560 +++++++++++++++++++++
  drivers/mmc/core/core.h                            |   7 +
  drivers/mmc/core/debugfs.c                         |  46 ++
  drivers/mmc/core/host.c                            |   8 +
  drivers/mmc/core/mmc.c                             | 200 +++++++-
  drivers/mmc/core/sd.c                              |  72 ++-
  drivers/mmc/host/sdhci-msm.c                       |  37 ++
  drivers/mmc/host/sdhci-pltfm.c                     |  11 +
  drivers/mmc/host/sdhci.c                           |  27 +
  drivers/mmc/host/sdhci.h                           |   8 +
  include/linux/mmc/card.h                           |   5 +
  include/linux/mmc/host.h                           |  70 +++
  13 files changed, 1059 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index 502b3b8..bd8470a 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -26,6 +26,15 @@ Required properties:
  	"cal"	- reference clock for RCLK delay calibration (optional)
  	"sleep"	- sleep clock for RCLK delay calibration (optional)
+Optional Properties:
+- qcom,devfreq,freq-table - specifies supported frequencies for clock scaling.
+				    Clock scaling logic shall toggle between these frequencies based
+				    on card load. In case the defined frequencies are over or below
+				    the supported card frequencies, they will be overridden
+				    during card init. In case this entry is not supplied,
+				    the driver will construct one based on the card
+				    supported max and min frequencies.
+				    The frequencies must be ordered from lowest to highest.
This should be a common binding in which case will just a list of
frequencies be sufficient.
[Sayali] : Can you please elaborate more on what do you mean by common binding here ? Like if you are referring to any already available property (by devfreq ?) to pass min-max frequencies ?
Any Documentation file to refer ?

Rob




[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux