On 27/08/18 13:10, Thierry Reding wrote: > On Fri, Aug 10, 2018 at 09:08:02PM +0300, Aapo Vienamo wrote: >> Hi all, >> >> This series implements support for faster signaling modes on Tegra >> SDHCI controllers. This series consist of several parts: changes >> requried for 1.8 V signaling and pad control, pad calibration, and >> tuning. Following earlies patch sets have been merged into this >> larger set: "Tegra PMC pinctrl pad configuration", "Tegra SDHCI enable >> 1.8 V signaling on Tegar210 and Tegra186", "Tegra SDHCI update the >> padautocal procedure". Also the patches for enabling SDHCI tuning >> are added. >> >> Changelog: >> v2: >> - Fix grammar in PMC device tree bindings docs >> - Remove a stray line from tegra sdhci bindings >> - Cosmetic changes to PMC pinctrl driver >> - Fix a typo in "soc/tegra: pmc: Implement >> tegra_io_pad_is_powered()" commit message >> - Declare mask and value on the same line in >> tegra_io_pad_is_powered() >> - Move the call to tegra_sdhci_is_pad_and_regulator_valid() to >> inside the if condition in tegra_sdhci_reset() >> - Use usleep_range() in tegra_sdhci_configure_cal_pad() >> - Move sdhci_writel() out of the enable if-else body in >> tegra_sdhci_configure_cal_pad() >> - Add a delay before starting polling in >> tegra_sdhci_pad_autocalib() >> - Use usleep_range() in tegra_sdhci_set_tap() >> - Rename orig_enabled to status in >> tegra_sdhci_configure_card_clk() >> - Fix if condition wrapping alignment in tegra_sdhci_set_tap() >> >> v1: >> - Probe the regulator voltage capabilities to determine whether pinctrl >> is needed in tegra_sdhci_r eset >> - Don't remove tegra_sdhci_voltage_switch() >> - Use dev_warn() in tegra_sdhci_init_pinctrl_info() >> - Don't change start_signal_voltage_switch callback if pinctrl info >> invalid >> - Only call udelay(1) on enable in tegra_sdhci_configure_cal_pad() >> - Add nvidia, prefix to pad autocal offset dt props in the example >> >> See the original patch sets for earlier changelogs. >> >> Aapo Vienamo (40): >> dt-bindings: Add Tegra PMC pad configuration bindings >> dt-bindings: mmc: tegra: Add pad voltage control properties >> dt-bindings: Add Tegra SDHCI pad pdpu offset bindings >> dt-bindings: mmc: Add Tegra SDHCI sampling trimmer values >> soc/tegra: pmc: Fix pad voltage configuration for Tegra186 >> soc/tegra: pmc: Factor out DPD register bit calculation >> soc/tegra: pmc: Implement tegra_io_pad_is_powered() >> soc/tegra: pmc: Use X macro to generate IO pad tables >> soc/tegra: pmc: Remove public pad voltage APIs >> soc/tegra: pmc: Implement pad configuration via pinctrl >> mmc: sdhci: Add a quirk to skip clearing the transfer mode register on >> tuning >> mmc: tegra: Reconfigure pad voltages during voltage switching >> mmc: tegra: Poll for calibration completion >> mmc: tegra: Set calibration pad voltage reference >> mmc: tegra: Power on the calibration pad >> mmc: tegra: Disable card clock during pad calibration >> mmc: tegra: Program pad autocal offsets from dt >> mmc: tegra: Perform pad calibration after voltage switch >> mmc: tegra: Enable pad calibration on Tegra210 and Tegra186 >> mmc: tegra: Add a workaround for tap value change glitch >> mmc: tegra: Parse default trim and tap from dt >> mmc: tegra: Configure default tap values >> mmc: tegra: Configure default trim value on reset >> mmc: tegra: Use standard SDHCI tuning on Tegra210 and Tegra186 >> mmc: sdhci: Add a quirk to disable card clock during tuning >> mmc: tegra: Enable workaround for tuning transfer mode bug >> mmc: tegra: Set SDHCI_QUIRK2_TUNE_DIS_CARD_CLK on Tegra210 >> mmc: tegra: Enable UHS and HS200 modes for Tegra210 >> mmc: tegra: Enable UHS and HS200 modes for Tegra186 >> arm64: dts: Add Tegra210 sdmmc pinctrl voltage states >> arm64: dts: Add Tegra186 sdmmc pinctrl voltage states >> arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V >> arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply >> arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1 >> arm64: dts: tegra186: Add sdmmc pad auto calibration offsets >> arm64: dts: tegra210: Add sdmmc pad auto calibration offsets >> arm64: dts: tegra210: Add SDHCI tap and trim values >> arm64: dts: tegra186: Add SDHCI tap and trim values >> arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4 >> arm64: dts: tegra210: Assign clocks for sdmmc1 and sdmmc4 >> >> .../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 93 ++++ >> .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 103 ++++ >> .../bindings/mmc/nvidia,tegra20-sdhci.txt | 68 +++ >> arch/arm64/boot/dts/nvidia/tegra186.dtsi | 74 +++ >> arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 12 +- >> arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 1 - >> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 55 ++ >> drivers/mmc/host/sdhci-tegra.c | 556 +++++++++++++++++++-- >> drivers/mmc/host/sdhci.c | 21 + >> drivers/mmc/host/sdhci.h | 4 + >> drivers/soc/tegra/pmc.c | 511 ++++++++++++++----- >> include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 + >> include/soc/tegra/pmc.h | 20 +- >> 13 files changed, 1324 insertions(+), 212 deletions(-) >> create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h > > Adrian, > > these patches are also a prerequisite for the UHS signalling changes in > the other two series that Aapo posted. It'd be great if you could take a > quick look and weigh in. Sure, I'll try and have a look today.
