On Thu, 23 Aug 2018 14:51:26 +0300 Adrian Hunter wrote:
> On 23/08/18 13:09, Jisheng Zhang wrote:
> > When using DMA, if the DMA addr spans 128MB boundary, we have to split
> > the DMA transfer into two so that each one doesn't exceed the boundary.
> >
> > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@xxxxxxxxxxxxx>
> > ---
> > drivers/mmc/host/sdhci-of-dwcmshc.c | 39 +++++++++++++++++++++++++++++
> > 1 file changed, 39 insertions(+)
> >
> > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > index 1b7cd144fb01..df0a3aeabe19 100644
> > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > @@ -8,21 +8,48 @@
> > */
> >
> > #include <linux/clk.h>
> > +#include <linux/mm.h>
> > #include <linux/module.h>
> > #include <linux/of.h>
> > +#include <linux/sizes.h>
> >
> > #include "sdhci-pltfm.h"
> >
> > +#define BOUNDARY_OK(addr, len) \
> > + ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
> > +
> > struct dwcmshc_priv {
> > struct clk *bus_clk;
> > };
> >
> > +/*
> > + * If DMA addr spans 128MB boundary, we split the DMA transfer into two
> > + * so that the DMA transfer doesn't exceed the boundary.
> > + */
> > +static void dwcmshc_adma_write_desc(struct sdhci_host *host, void **desc,
> > + dma_addr_t addr, int len, unsigned int cmd)
> > +{
> > + int tmplen, offset;
> > +
> > + if (likely(!len || BOUNDARY_OK(addr, len)))
> > + sdhci_adma_write_desc(host, desc, addr, len, cmd);
>
> Doesn't this need a return? i.e.
>
> return;
oops, I made a mistake here. Pre v4, there's a return...
Thanks so much.
> }
>
> > +
> > + offset = addr & (SZ_128M - 1);
> > + tmplen = SZ_128M - offset;
> > + sdhci_adma_write_desc(host, desc, addr, tmplen, cmd);
> > +
> > + addr += tmplen;
> > + len -= tmplen;
> > + sdhci_adma_write_desc(host, desc, addr, len, cmd);
> > +}
> > +
> > static const struct sdhci_ops sdhci_dwcmshc_ops = {
> > .set_clock = sdhci_set_clock,
> > .set_bus_width = sdhci_set_bus_width,
> > .set_uhs_signaling = sdhci_set_uhs_signaling,
> > .get_max_clock = sdhci_pltfm_clk_get_max_clock,
> > .reset = sdhci_reset,
> > + .adma_write_desc = dwcmshc_adma_write_desc,
> > };
> >
> > static const struct sdhci_pltfm_data sdhci_dwcmshc_pdata = {
> > @@ -36,12 +63,24 @@ static int dwcmshc_probe(struct platform_device *pdev)
> > struct sdhci_host *host;
> > struct dwcmshc_priv *priv;
> > int err;
> > + u32 extra;
> >
> > host = sdhci_pltfm_init(pdev, &sdhci_dwcmshc_pdata,
> > sizeof(struct dwcmshc_priv));
> > if (IS_ERR(host))
> > return PTR_ERR(host);
> >
> > + /*
> > + * The DMA table descriptor count is calculated as the maximum
> > + * number of segments times 2, to allow for an alignment
> > + * descriptor for each segment, plus 1 for a nop end descriptor,
> > + * plus extra number for cross 128M boundary handling.
> > + */
> > + extra = DIV_ROUND_UP(totalram_pages, SZ_128M / PAGE_SIZE);
>
> You are assuming here that totalram_pages gives you the highest physical
> page number. Is that true?
Per my understanding, it's true. What I need is the MemTotal/PAGE_SIZE where
Memtotal is from /proc/meminfo. After reading the code, I found this is
totalram_pages as shown in si_meminfo()
>
> > + if (extra > SDHCI_MAX_SEGS)
> > + extra = SDHCI_MAX_SEGS;
> > + host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1 + extra;
>
> That should be:
>
> host->adma_table_cnt += extra;
yep, will do in v5
>
> > +
> > pltfm_host = sdhci_priv(host);
> > priv = sdhci_pltfm_priv(pltfm_host);
> >
> >
>
