Re: [PATCH 13/40] mmc: tegra: Poll for calibration completion

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 9 Aug 2018 14:46:16 +0200
Thierry Reding <thierry.reding@xxxxxxxxx> wrote:

> On Wed, Aug 01, 2018 at 07:32:03PM +0300, Aapo Vienamo wrote:
> > Implement polling with 10 ms timeout for automatic pad drive strength
> > calibration.
> > 
> > Signed-off-by: Aapo Vienamo <avienamo@xxxxxxxxxx>
> > ---
> >  drivers/mmc/host/sdhci-tegra.c | 21 ++++++++++++++++-----
> >  1 file changed, 16 insertions(+), 5 deletions(-)
> > 
> > diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> > index 7d98455..c8ff267 100644
> > --- a/drivers/mmc/host/sdhci-tegra.c
> > +++ b/drivers/mmc/host/sdhci-tegra.c
> > @@ -16,6 +16,7 @@
> >  #include <linux/err.h>
> >  #include <linux/module.h>
> >  #include <linux/init.h>
> > +#include <linux/iopoll.h>
> >  #include <linux/platform_device.h>
> >  #include <linux/clk.h>
> >  #include <linux/io.h>
> > @@ -50,6 +51,9 @@
> >  #define SDHCI_AUTO_CAL_START			BIT(31)
> >  #define SDHCI_AUTO_CAL_ENABLE			BIT(29)
> >  
> > +#define SDHCI_TEGRA_AUTO_CAL_STATUS		0x1ec
> > +#define SDHCI_TEGRA_AUTO_CAL_ACTIVE		BIT(31)
> > +
> >  #define NVQUIRK_FORCE_SDHCI_SPEC_200	BIT(0)
> >  #define NVQUIRK_ENABLE_BLOCK_GAP_DET	BIT(1)
> >  #define NVQUIRK_ENABLE_SDHCI_SPEC_300	BIT(2)
> > @@ -228,13 +232,20 @@ static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
> >  
> >  static void tegra_sdhci_pad_autocalib(struct sdhci_host *host)
> >  {
> > -	u32 val;
> > +	u32 reg;
> > +	int ret;
> > +
> > +	reg = sdhci_readl(host, SDHCI_TEGRA_AUTO_CAL_CONFIG);
> > +	reg |= SDHCI_AUTO_CAL_ENABLE | SDHCI_AUTO_CAL_START;
> > +	sdhci_writel(host, reg, SDHCI_TEGRA_AUTO_CAL_CONFIG);
> >    
> 
> I know this is preexisting, but I want to make sure we cover this so we
> don't run into this down the road: do these bits automatically clear on
> calibration completion? Can we run these multiple times and get
> everything properly calibrated?

The TRM states in the pad auto-calibration procedure description that
this bit should not be cleared.

 -Aapo
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux