> -----Original Message----- > From: Stefan Agner [mailto:stefan@xxxxxxxx] > Sent: Thursday, June 28, 2018 4:13 PM > To: adrian.hunter@xxxxxxxxx; ulf.hansson@xxxxxxxxxx > Cc: Fabio Estevam <fabio.estevam@xxxxxxx>; Bough Chen > <haibo.chen@xxxxxxx>; A.s. Dong <aisheng.dong@xxxxxxx>; > michael@xxxxxxxxxxxxxxxxxxxx; rmk+kernel@xxxxxxxxxxxxxxx; linux- > mmc@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Stefan Agner > <stefan@xxxxxxxx> > Subject: [PATCH 1/3] mmc: sdhci-esdhc-imx: get rid of support_vsel > > The field support_vsel is currently only used in the device tree case. Get rid > of it. No change in behavior. > I'm not sure if it's quite necessary to remove it as it's used to bypass 100Mhz above pad settings look up which is meaningless if user claims no 1-8 v support. If you remove it, probably you still need better check the quirk for Pad state look up. Regards Dong Aisheng > Signed-off-by: Stefan Agner <stefan@xxxxxxxx> > --- > drivers/mmc/host/sdhci-esdhc-imx.c | 8 ++------ > include/linux/platform_data/mmc-esdhc-imx.h | 2 -- > 2 files changed, 2 insertions(+), 8 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci- > esdhc-imx.c > index 6f444731754d..20a420b765b3 100644 > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > @@ -1145,18 +1145,14 @@ sdhci_esdhc_imx_probe_dt(struct > platform_device *pdev, > &boarddata->tuning_start_tap); > > if (of_find_property(np, "no-1-8-v", NULL)) > - boarddata->support_vsel = false; > - else > - boarddata->support_vsel = true; > + host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; > > if (of_property_read_u32(np, "fsl,delay-line", &boarddata- > >delay_line)) > boarddata->delay_line = 0; > > mmc_of_parse_voltage(np, &host->ocr_mask); > > - /* sdr50 and sdr104 need work on 1.8v signal voltage */ > - if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data) && > - !IS_ERR(imx_data->pins_default)) { > + if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pins_default)) > { > imx_data->pins_100mhz = pinctrl_lookup_state(imx_data- > >pinctrl, > > ESDHC_PINCTRL_STATE_100MHZ); > imx_data->pins_200mhz = pinctrl_lookup_state(imx_data- > >pinctrl, > diff --git a/include/linux/platform_data/mmc-esdhc-imx.h > b/include/linux/platform_data/mmc-esdhc-imx.h > index 7daa78a2f342..640dec8b5b0c 100644 > --- a/include/linux/platform_data/mmc-esdhc-imx.h > +++ b/include/linux/platform_data/mmc-esdhc-imx.h > @@ -34,7 +34,6 @@ enum cd_types { > * @cd_gpio: gpio for card_detect interrupt > * @wp_type: type of write_protect method (see wp_types enum above) > * @cd_type: type of card_detect method (see cd_types enum above) > - * @support_vsel: indicate it supports 1.8v switching > */ > > struct esdhc_platform_data { > @@ -43,7 +42,6 @@ struct esdhc_platform_data { > enum wp_types wp_type; > enum cd_types cd_type; > int max_bus_width; > - bool support_vsel; > unsigned int delay_line; > unsigned int tuning_step; /* The delay cell steps in tuning > procedure */ > unsigned int tuning_start_tap; /* The start delay cell point in tuning > procedure */ > -- > 2.18.0 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
