On 04/07/18 14:34, Ulf Hansson wrote:
> On 4 July 2018 at 13:34, Marc Zyngier <marc.zyngier@xxxxxxx> wrote:
>> On 04/07/18 11:50, Ulf Hansson wrote:
>>> + Marc
>>>
>>> On 4 July 2018 at 08:28, Stefan Mavrodiev <stefan@xxxxxxxxxx> wrote:
>>>> When mmc host controller enters suspend state, the clocks are
>>>> disabled, but irqs are not. For some reason the irqchip emits
>>>> false interrupts, which causes system lock loop.
>>>>
>>>> Debug log is:
>>>> ...
>>>> sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
>>>> sunxi-mmc 1c11000.mmc: enabling the clock
>>>> sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
>>>> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
>>>> sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
>>>> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
>>>> sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
>>>> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
>>>> mmc1: new DDR MMC card at address 0001
>>>> mmcblk1: mmc1:0001 AGND3R 14.6 GiB
>>>> mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
>>>> mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
>>>> sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
>>>> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
>>>> mmcblk1: p1
>>>> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
>>>> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
>>>> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
>>>> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
>>>> and so on...
>>>>
>>>> This issue apears on eMMC cards, routed on MMC2 slot. The patch is
>>>> tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
>>>>
>>>> Fixes: 9a8e1e8cc2c0 ("mmc: sunxi: Add runtime_pm support")
>>>> Signed-off-by: Stefan Mavrodiev <stefan@xxxxxxxxxx>
>>>> ---
>>>> Changes in v2:
>>>> - Add comment why disable_irq() is necessary
>>>>
>>>> ---
>>>> drivers/mmc/host/sunxi-mmc.c | 7 +++++++
>>>> 1 file changed, 7 insertions(+)
>>>>
>>>> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
>>>> index e747259..8e7f3e3 100644
>>>> --- a/drivers/mmc/host/sunxi-mmc.c
>>>> +++ b/drivers/mmc/host/sunxi-mmc.c
>>>> @@ -1446,6 +1446,7 @@ static int sunxi_mmc_runtime_resume(struct device *dev)
>>>> sunxi_mmc_init_host(host);
>>>> sunxi_mmc_set_bus_width(host, mmc->ios.bus_width);
>>>> sunxi_mmc_set_clk(host, &mmc->ios);
>>>> + enable_irq(host->irq);
>>>>
>>>> return 0;
>>>> }
>>>> @@ -1455,6 +1456,12 @@ static int sunxi_mmc_runtime_suspend(struct device *dev)
>>>> struct mmc_host *mmc = dev_get_drvdata(dev);
>>>> struct sunxi_mmc_host *host = mmc_priv(mmc);
>>>>
>>>> + /*
>>>> + * When clocks are off, it's possible receiving
>>>> + * fake interrupts, which will stall the system.
>>>> + * Disabling the irq will prevent this.
>>>> + */
>>>> + disable_irq(host->irq);
>>>
>>> No, this doesn't work for shared IRQs.
>>
>> Well, in this case, it does work, because that interrupt line cannot be
>> shared with anything else, if I understand how the SoC is wired: each
>> MMC controller has a dedicated interrupt line to the GIC, and it isn't
>> shared with anything (that's on the A20 though, and I don't know about
>> other SoCs integrating the same IP).
>
> That's the problem. This may work on some SoCs but not on others.
>
>>
>>>
>>>> sunxi_mmc_reset_host(host);
>>>> sunxi_mmc_disable(host);
>>>>
>>>> --
>>>> 2.7.4
>>>>
>>>
>>> The only option today is to use free_irq() in runtime suspend and then
>>> re-request the irq to re-install the handler at runtime resume.
>>>
>>> That's not an optimal solution, which is pointed out in the below
>>> discussion as well. Moreover, it has also turned out using free_irq()
>>> is also problematic in cases threaded handlers are used.
>>>
>>> Here's the link to the discussion, it's not the only one I know of, so
>>> this is common problem.
>>> https://lkml.org/lkml/2016/1/28/213
>>>
>>> Care to have a hack on the "common" solution, which in principle means
>>> adding APIs to genirq that can disable/enable handlers from being
>>> called, rather than the entire IRQ line.
>>
>> That doesn't work. You still end-up with a screaming interrupt, and you
>> will still spend 100% of your time in interrupt context for nothing.
>>
>> Eventually, the kernel will have enough (the /other/ shared handlers
>> returning IRQ_NONE all the time), and will forcefully kill that
>> particular interrupt interrupt line, meaning you end-up in the same
>> situation of having the line disabled for all the users of that
>> interrupt line. Except that now, it is disabled forever.
>
> Ahh, correct!
>
> Sounds like free_irq() is what we need. Only that it's bit heavy
> weight as we need to re-install handlers.
>
>>
>> A better fix would be to kill the interrupt generation at the source
>> (the MMC controller in this particular case) when suspending.
>
> Right. But using disable_irq() doesn't work a general solution, so
> something else is needed.
Which is why I asked whether there was a way to prevent interrupts from
being generated at the MMC controller level. Most IPs have something
there, and I'd be surprised if there wasn't anything to that effect in
the SDHCI spec.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
