On 20/04/18 19:39, ernest.zhang wrote:
> Add MSI interrupt support if the SD host device can support MSI interrupt.
>
> Changes in V5:
The change log goes below the --- line or in a separate cover email.
> 1. Because pci_enable_msi is marked as deprecated and should not be
> used in new code, use pci_alloc_irq_vectors instead.
> 2. Remove unneeded CONFIG_PCI_MSI macro check
>
> Changes in V4:
> Enable MSI interrupt if the MSI capability bit is set in
> capability register.
>
> Changes in V3:
> None. This patch is add in V4.
>
> Changes in V2:
> None. This patch is add in V4.
>
> Changes in V1:
> None. This patch is add in V4.
>
> Signed-off-by: ernest.zhang <ernest.zhang@xxxxxxxxxxxxxx>
> ---
> drivers/mmc/host/sdhci-pci-o2micro.c | 30 +++++++++++++++++++++++++++---
> 1 file changed, 27 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index 96adaae..374c783 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -358,11 +358,13 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
> {
> struct sdhci_pci_chip *chip;
> struct sdhci_host *host;
> + struct mmc_host *mmc;
> u32 reg;
> int ret;
>
> chip = slot->chip;
> host = slot->host;
> + mmc = host->mmc;
> switch (chip->pdev->device) {
> case PCI_DEVICE_ID_O2_SDS0:
> case PCI_DEVICE_ID_O2_SEABIRD0:
> @@ -373,6 +375,28 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
> if (reg & 0x1)
> host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
>
> + if (pci_find_capability(chip->pdev, PCI_CAP_ID_MSI)) {
> + ret = pci_alloc_irq_vectors(chip->pdev, 1, 1,
> + PCI_IRQ_MSI | PCI_IRQ_MSIX);
> + if (ret == 1) {
> + ret = pci_irq_vector(chip->pdev, 0);
> + if (ret >= 0) {
> + host->irq = ret;
> + pr_info("%s: use MSI irq, irq=%d\n",
> + mmc_hostname(mmc), host->irq);
> + } else {
> + pr_err("%s: failed to get device irq, err=%d\n",
> + mmc_hostname(mmc), ret);
> + }
> + } else {
> + pr_err("%s: enable PCI MSI failed, err=%d\n",
> + mmc_hostname(mmc), ret);
> + }
> + } else {
> + pr_info("%s: unsupport msi, use INTx irq\n",
> + mmc_hostname(mmc));
> + }
There seem to be more prints here than you really need. Please reduce them
and make this a separate function.
> +
> if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
> ret = pci_read_config_dword(chip->pdev,
> O2_SD_MISC_SETTING, ®);
> @@ -380,11 +404,11 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
> return -EIO;
> if (reg & (1 << 4)) {
> pr_info("%s: emmc 1.8v flag is set, force 1.8v signaling voltage\n",
> - mmc_hostname(host->mmc));
> + mmc_hostname(mmc));
The change from using 'host->mmc' to using local variable 'mmc' needs to be
a separate patch.
> host->flags &= ~SDHCI_SIGNALING_330;
> host->flags |= SDHCI_SIGNALING_180;
> - host->mmc->caps2 |= MMC_CAP2_NO_SD;
> - host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
> + mmc->caps2 |= MMC_CAP2_NO_SD;
> + mmc->caps2 |= MMC_CAP2_NO_SDIO;
Ditto
> }
> }
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
