On 8 February 2018 at 15:59, Quentin Schulz <quentin.schulz@xxxxxxxxxxx> wrote: > Hi Ulf, > > On Wed, Aug 30, 2017 at 03:43:49PM +0200, Ulf Hansson wrote: >> On 30 August 2017 at 14:44, Hans de Goede <hdegoede@xxxxxxxxxx> wrote: >> > Hi, >> > >> > >> > On 21-07-17 16:35, Quentin Schulz wrote: >> >> >> >> From: Hans de Goede <hdegoede@xxxxxxxxxx> >> >> >> >> Some sdio devices have a multiple stage bring-up process. Specifically >> >> the esp8089 (for which an out of tree driver is available) loads firmware >> >> on the first call to its sdio-drivers' probe function and then resets >> >> the device causing it to reboot from its RAM with the new firmware. >> >> >> >> When this sdio device reboots it comes back up in 1 bit 400 KHz mode >> >> again, and we need to walk through the whole ios negatiation and sdio >> >> setup >> >> again. >> >> >> >> There are 2 problems with this: >> >> >> >> 1) Typically these devices are soldered onto some (ARM) tablet / SBC >> >> PCB and as such are described in devicetree as "non-removable", which >> >> causes the mmc-core to scan them only once and not poll for the device >> >> dropping of the bus. Normally this is the right thing todo but in the >> >> eso8089 example we need the mmc-core to notice the module has disconnected >> >> (since it is now in 1 bit mode again it will not talk to the host in 4 bit >> >> mode). This can be worked around by using "broken-cd" in devicetree >> >> instead of "non-removable", but that is not a proper fix since the device >> >> really is non-removable. >> >> >> >> 2) When the mmc-core detects the device has disconnected it will poweroff >> >> the device, causing the RAM loaded firmware to be lost. This can be worked >> >> around in devicetree by using regulator-always-on (and avoiding the use of >> >> mmc-pwrseq), but again that is more of a hack then a proper fix. >> >> >> >> This commmit fixes 1) by adding a mmc_force_detect_change function which >> >> will cause scanning for device removal / insertion until a new device is >> >> detected. 2) Is fixed by a keep_power flag to the mmc_force_detect_change >> >> function which when set causes the mmc-core to keep the power to the >> >> device >> >> on during the rescan. >> >> >> >> Cc: Icenowy Zheng <icenowy@xxxxxxxx> >> >> Cc: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx> >> >> Cc: Chen-Yu Tsai <wens@xxxxxxxx> >> >> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> >> > >> > >> > So when I posted this patch quite a while back, there was some discussion >> > about this and a consensus that this is not the right solution. >> > >> > So first of all lets describe the problem: >> > >> > The esp8089 sdio wifi chip is really an ARM core with a wifi phy >> > connected to it (as many wifi chipsets are). >> > >> > But this one comes up in some really generic sdio capable boot-loader >> > mode and we need to feed it firmware and then reboot it into the >> > new firmware. >> > >> > The reboot is where the problems happens. It seems to fallback >> > from the negotiated 4 wire sdio mode to single wire spi mode then. >> > >> > The out of tree version of the driver deals with this by not setting >> > the non-removable flag as well as setting the broken_cd flag so that >> > the mmc core polls the device, after the reboot the poll fails >> > because the mmc-controller and the esp8089 are using a different >> > amount of wires so the mmc-cmd the poll uses times out. >> > >> > After which the esp8089 drivers remove function gets called, and >> > the mmc stack re-discovers the esp8089 by restarting the whole >> > number of wires (and speed) used negotiation. After which the >> > esp8089 driver's probe function gets called (again) and on >> > firmware loading is has set a global flag, so now it actually >> > acts as a wifi driver rather then trying to load the firmware >> > a second time. >> > >> > Since I did not want to rely on broken_cd polling I came up >> > with the hack which is this patch. >> > >> > So when this patch was first discussed we came to the conclusion >> > that what we really need is some sort of mmc_reprobe_device >> > function which the driver can call from probe which will >> > redo the number of wires (and speed) used negotiation, >> > while keeping the sdio_function device as is so that probe can >> > simply continue after this and we also don't need the ugly >> > global flag. >> > >> > The idea would be for this function to be some wrapper >> > around mmc_init_card() which resets the ios settings as is >> > normally done on remove and then call mmc_init_card() >> > passing in the existing card the same way as is done >> > one resume, so that the existing card / sdio_function >> > devices get reused. >> > >> > IIRC Ulf would look into writing this mmc_reprobe_device >> > function and then I would test it with the esp8089, but >> > Ulf never got around to writing the function and I ended >> > up working on other things too. >> >> Thanks for summary! >> >> Just to let you know, I haven't forgot about this problem. I am >> planning for a major update of the SDIO for power management support, >> within a not too far future. >> The issue described above, is then also one of the things I also plan >> to look into. >> > > I'd like to know if any progress has been made on that problem (I may > have missed patches). > Had you had the time to look at the issue? I have looked at the issue, but not manage to cook some patches for it. However, it's on my top of my TODO list for mmc. No promises, but perhaps and hopefully I manage to get something posted during the coming release cycle. Sorry for the delay! Br Uffe -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
