card_busy ops is used by mmc core in 1) mmc_set_uhs_voltage to verify voltage switch 2) __mmc_start_request/mmc_poll_for_busy to check the card busy status While only DAT0 can be used to check the card busy status (in '2' above), CMD and DAT[0..3] is used to verify voltage switch (in '1' above). The voltage switching sequence for AM572x platform is mentioned in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM (SPRUHZ6I - October 2014–Revised April 2017 [1]). Add card_busy host ops in sdhci_omap that checks for both CMD and DAT[0..3]. card_busy here returns true if one of CMD and DAT[0..3] is low though during voltage switch sequence all of CMD and DAT[0..3] has to be low (however haven't observed a case where some DAT lines are low and some are high). In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON should also be set after switching to 1.8v which is also taken care in the card_busy ops. [1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx> --- drivers/mmc/host/sdhci-omap.c | 62 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+) diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c index 96985786cadf..defe4eac020d 100644 --- a/drivers/mmc/host/sdhci-omap.c +++ b/drivers/mmc/host/sdhci-omap.c @@ -31,11 +31,20 @@ #define SDHCI_OMAP_CON 0x12c #define CON_DW8 BIT(5) #define CON_DMA_MASTER BIT(20) +#define CON_CLKEXTFREE BIT(16) +#define CON_PADEN BIT(15) #define CON_INIT BIT(1) #define CON_OD BIT(0) #define SDHCI_OMAP_CMD 0x20c +#define SDHCI_OMAP_PSTATE 0x0224 +#define PSTATE_CLEV BIT(24) +#define PSTATE_DLEV_SHIFT 20 +#define PSTATE_DLEV_DAT(x) (1 << (PSTATE_DLEV_SHIFT + (x))) +#define PSTATE_DLEV (PSTATE_DLEV_DAT(0) | PSTATE_DLEV_DAT(1) | \ + PSTATE_DLEV_DAT(2) | PSTATE_DLEV_DAT(3)) + #define SDHCI_OMAP_HCTL 0x228 #define HCTL_SDBP BIT(8) #define HCTL_SDVS_SHIFT 9 @@ -191,6 +200,58 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host, } } +static int sdhci_omap_card_busy(struct mmc_host *mmc) +{ + int i; + u32 reg, ac12; + int ret = true; + struct sdhci_host *host = mmc_priv(mmc); + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_omap_host *omap_host; + u32 ier = host->ier; + + pltfm_host = sdhci_priv(host); + omap_host = sdhci_pltfm_priv(pltfm_host); + + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + ac12 = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12); + reg &= ~CON_CLKEXTFREE; + if (ac12 & AC12_V1V8_SIGEN) + reg |= CON_CLKEXTFREE; + reg |= CON_PADEN; + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + disable_irq(host->irq); + ier |= SDHCI_INT_CARD_INT; + sdhci_writel(host, ier, SDHCI_INT_ENABLE); + sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE); + + for (i = 0; i < 5; i++) { + /* + * Delay is required for PSTATE to correctly reflect + * DLEV/CLEV values after PADEM is set. + */ + usleep_range(100, 200); + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_PSTATE); + if ((reg & PSTATE_CLEV) && + ((reg & PSTATE_DLEV) == PSTATE_DLEV)) { + ret = false; + goto ret; + } + } + +ret: + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + reg &= ~(CON_CLKEXTFREE | CON_PADEN); + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); + enable_irq(host->irq); + + return ret; +} + static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) { @@ -562,6 +623,7 @@ static int sdhci_omap_probe(struct platform_device *pdev) host->mmc_host_ops.start_signal_voltage_switch = sdhci_omap_start_signal_voltage_switch; host->mmc_host_ops.set_ios = sdhci_omap_set_ios; + host->mmc_host_ops.card_busy = sdhci_omap_card_busy; sdhci_read_caps(host); host->caps |= SDHCI_CAN_DO_ADMA2; -- 2.11.0 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
