On 3 July 2017 at 21:28, Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx> wrote: > I always anticipated this code to be not correct, but now I had a test > case to prove it. According to all documentation I have, setting the > TMIO_STOP_STP bit ever only worked during block transfers. This bit is > like manually enforcing an autocmd12 during a so far seamless transfer. > It does NOT work when the block transfer had errors. It also does NOT > work with any other cmd except block commands. For all those, CMD12 has > to be treated like any other command. So, basically, we could use this > bit only for mrq->data->stop cmds. But for these, we happily use the > autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above > bit is not useful for us and we need to treat CMD12 as a regular cmd > always. Just remove the special handling code. Note that the BSP > recognized this issue as well yet had a more cautious solution to the > problem [1]. Which is understandable but makes CMD12 handling even more > complicated. > > Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when > retuning one of my SD cards. > > [1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183a > > Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx> Thanks, applied for next! Should we add a stable tag? Kind regards Uffe > --- > > So, this is a friendly call for further testing to make sure no regressions > happen. I also put the authors of the BSP patch to CC to check if this patch > also matches their use case. I hope this is fine for these people, please > accept my apologies if not. I just really like to have your opinion on this > patch. > > Geert, Simon: any chance you can run this patch on your board farms? > > In any case: as far as my understanding goes, if I am wrong with my > assumptions, the worst case is that for older SoCs CMD12 handling might become > a tad more inefficient because we now do in software what was expected to be > done in hardware. However, I am quite sure that the HW feature was always > over-estimated and CMD12 support is simply broken. For my test case and the BSP > patch above, it definately was. > > Thanks for any assistance, > > Wolfram > > > drivers/mmc/host/tmio_mmc_core.c | 6 ------ > 1 file changed, 6 deletions(-) > > diff --git a/drivers/mmc/host/tmio_mmc_core.c b/drivers/mmc/host/tmio_mmc_core.c > index 1851c883bfc82a..fbcd56c58bce24 100644 > --- a/drivers/mmc/host/tmio_mmc_core.c > +++ b/drivers/mmc/host/tmio_mmc_core.c > @@ -355,12 +355,6 @@ static int tmio_mmc_start_command(struct tmio_mmc_host *host, > int c = cmd->opcode; > u32 irq_mask = TMIO_MASK_CMD; > > - /* CMD12 is handled by hardware */ > - if (cmd->opcode == MMC_STOP_TRANSMISSION && !cmd->arg) { > - sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, TMIO_STOP_STP); > - return 0; > - } > - > switch (mmc_resp_type(cmd)) { > case MMC_RSP_NONE: c |= RESP_NONE; break; > case MMC_RSP_R1: > -- > 2.11.0 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
