Hi Andrian and Uffe, Do you have any comments on MMC patches? Could you help to merge the mmc patches if there is no changes requested? Regarding to the dts patches, I have some more platforms to support. So I'd like to drop them currently, and send them all to arm mailing list for reviewing. Thanks a lot. Best regards, Yangbo Lu > -----Original Message----- > From: Y.B. Lu > Sent: Thursday, April 06, 2017 4:02 PM > To: Y.B. Lu; linux-mmc@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; ulf.hansson@xxxxxxxxxx; Adrian > Hunter; Rob Herring; Mark Rutland; Catalin Marinas; Will Deacon > Cc: Xiaobo Xie > Subject: RE: [v3, 0/7] Add SD UHS-I and eMMC HS200 support for eSDHC > > Hi all, > > Any comments? Thanks. > > > Best regards, > Yangbo Lu > > > -----Original Message----- > > From: Yangbo Lu [mailto:yangbo.lu@xxxxxxx] > > Sent: Monday, March 27, 2017 3:50 PM > > To: linux-mmc@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-arm- > > kernel@xxxxxxxxxxxxxxxxxxx; ulf.hansson@xxxxxxxxxx; Adrian Hunter; Rob > > Herring; Mark Rutland; Catalin Marinas; Will Deacon > > Cc: Xiaobo Xie; Y.B. Lu > > Subject: [v3, 0/7] Add SD UHS-I and eMMC HS200 support for eSDHC > > > > It's complicated to support SD UHS-I and eMMC HS200 for eSDHC because > > there're many differences between eSDHC and SD/eMMC spec. Several > > differences as below must be considered: > > 1. Peripheral clock must be used instead of platform clock. > > - eSDHC could select peripheral clock or platform clock as its > clock > > source. According to RM, UHS-I/HS200 must use peripheral clock > > since > > it supports higher frequency than platform clock. > > - Patch 1 and patch 6 is to support this. > > 2. Signal voltage switching requires a control circuit out of eSDHC. > > - eSDHC supports signal voltage switch from 3.3v to 1.8v by > > eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output > > signal SDHC_VS, and there must be a control circuit out of eSDHC > > to change the signal voltage according to SDHC_VS output signal. > > - Patch 2 is to support this. > > 3. eSDHC uses tuning block for tuning procedure. > > - Tuning clock control register must be configured before tuning. > > - Patch 3 is to support this. > > 4. Delay is needed between tuning cycles for HS200 tuning. > > - Once a patch removed mdelay between tuning cycles. > > But eSDHC needs it. > > - Patch 4 and patch 5 is to support this. > > 5. UHS-I/HS200 modes could be enabled in dts node. > > - Patch 7 is to support this. > > > > Please review and merge these patches on mmc git tree if no changes > > are required. > > > > Adrian Hunter (1): > > mmc: sdhci: Control the delay between tuning commands > > > > Yangbo Lu (6): > > mmc: sdhci-of-esdhc: add peripheral clock support > > mmc: sdhci-of-esdhc: add support for signal voltage switch > > mmc: sdhci-of-esdhc: add tuning support > > mmc: sdhci-of-esdhc: add delay between tuning cycles > > arm64: dts: ls1046a: add clocks property and compatible for eSDHC > node > > arm64: dts: ls1046ardb: add MMC HS200/UHS-1 modes support > > > > arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 8 ++ > > arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 3 +- > > drivers/mmc/host/sdhci-esdhc.h | 7 + > > drivers/mmc/host/sdhci-of-esdhc.c | 165 > > +++++++++++++++++++++- > > drivers/mmc/host/sdhci.c | 11 +- > > drivers/mmc/host/sdhci.h | 2 + > > 6 files changed, 190 insertions(+), 6 deletions(-) > > > > -- > > 2.1.0.27.g96db324 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
