Am 18.03.2017 um 09:11 schrieb Helmut Klein:
> On 17.03.2017 20:54, Heiner Kallweit wrote:
>> Am 17.03.2017 um 19:00 schrieb Helmut Klein:
>>> On 17.03.2017 07:44, Heiner Kallweit wrote:
>>>> Am 16.03.2017 um 22:12 schrieb Helmut Klein:
>>>>> Hallo Heiner,
>>>>>
>>>>> i applied your 2nd patch sets to linux-amlogic. (and of course the older set v5 1...10).
>>>>>
>>>>> The performance of the sd-card and the mmc-chip of my minimx is much better now.
>>>>>
>>>>> sd-card: from 6.5 to 22.5 MBytes/s
>>>>> mmc: from 14.5 to 28.5 MBytes/s (hs200 compatible device)
>>>>>
>>>>> But:
>>>>> the wifi-adapter is no longer operational. The problem starts with patch 3 and gets worse with patch 5.
>>>>>
>>>>> the adapter (ap6330) is attached to the sdio port of the the s905. (=mmc1)
>>>>>
>>>> Thanks for testing and sharing the feedback. Much appreciated.
>>>> The board I test on supports block devices only.
>>>>
>>>> Could you please share few more details:
>>>> - Drivers involved
>>>> - All syslog messages related to the device / driver
>>>>
>>>> And please set the relevant mailing lists on cc when providing test feedback.
>>>> Others might find your feedback helpful too.
>>>>
>>>> Thanks, Heiner
>>>>
>>>>> so i think it is important to test your patch set asap on an officially supported board with a wifi adapter).
>>>>>
>>>>> regards
>>>>> Helmut
>>>>>
>>>>
>>>>
>>>
>>> The driver for the wifi adapter is brcmfmac. It is compiled as a module and loaded via /etc/modules.
>>> the driver depends on the modules brcmutil and cfg80211, which are auto loaded.
>>>
>>> my user space is debian unstable. The kernel is cross compiled on my x86-64 laptop with gcc 5.4.1
>>>
>>> i use my own kernel configuration without an initial ramdisk. mmc, usb & ext4 drivers are compiled into the kernel
>>>
>>> kernel & dtb are loaded by u-boot from mmcblk2p1 (sd-card)
>>>
>>> the drive for the kernel is sda2 (sd-card inside of a usb card reader).
>>>
>>>
>>> here is the filtered (mmc|brcmfmac) syslog output when only patches 1 & 2 are applied
>>>
>>> [ 1.685012] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
>>> [ 1.873010] mmc0: new DDR MMC card at address 0001
>>> [ 1.873258] mmcblk0: mmc0:0001 NCard 14.5 GiB
>>> [ 1.876731] mmcblk0boot0: mmc0:0001 NCard partition 1 4.00 MiB
>>> [ 1.882597] mmcblk0boot1: mmc0:0001 NCard partition 2 4.00 MiB
>>> [ 2.004399] meson-gx-mmc d0070000.mmc: allocated mmc-pwrseq
>>> [ 2.048160] meson-gx-mmc d0072000.mmc: Got CD GPIO
>>> [ 2.066962] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
>>> [ 2.068985] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.074242] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.081275] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
>>> [ 2.124761] mmc2: Skipping voltage switch
>>> [ 2.153763] mmc1: new high speed SDIO card at address 0001
>>> [ 2.158567] mmc2: new high speed SDHC card at address 59b4
>>> [ 2.159219] mmcblk2: mmc2:59b4 USD00 29.5 GiB
>>> [ 2.164206] mmcblk2: p1 p2
>>> [ 6.664118] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Jan 6 2014 15:11:29 version 5.90.195.89.13 FWID 01-72f124c5
>>> [ 6.736239] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
>>> [ 6.928045] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 184
>>> [ 6.930475] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 188
>>> [ 6.938524] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 192
>>> [ 6.946543] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 196
>>> [ 6.954566] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 200
>>> [ 6.954663] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
>>> [ 6.969995] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 204
>>> [ 6.978023] brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 208
>>>
>>> this is the output after adding patch 3
>>>
>>> [ 1.684982] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
>>> [ 1.873041] mmc0: new DDR MMC card at address 0001
>>> [ 1.873273] mmcblk0: mmc0:0001 NCard 14.5 GiB
>>> [ 1.876765] mmcblk0boot0: mmc0:0001 NCard partition 1 4.00 MiB
>>> [ 1.882621] mmcblk0boot1: mmc0:0001 NCard partition 2 4.00 MiB
>>> [ 2.004408] meson-gx-mmc d0070000.mmc: allocated mmc-pwrseq
>>> [ 2.048189] meson-gx-mmc d0072000.mmc: Got CD GPIO
>>> [ 2.066978] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
>>> [ 2.069001] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.074253] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.081285] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
>>> [ 2.124874] mmc2: Skipping voltage switch
>>> [ 2.153475] mmc1: new high speed SDIO card at address 0001
>>> [ 2.158610] mmc2: new high speed SDHC card at address 59b4
>>> [ 2.158935] mmcblk2: mmc2:59b4 USD00 29.5 GiB
>>> [ 2.163910] mmcblk2: p1 p2
>>> [ 6.586318] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed <<<=====
>>> [ 6.586810] brcmfmac: brcmf_sdio_download_code_file: error -84 on writing 239507 membytes at 0x00000000
>>> [ 6.596373] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
>>>
>>> and this is the output after adding patches 4 & 5
>>>
>>> [ 1.684941] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
>>> [ 1.868910] mmc0: new DDR MMC card at address 0001
>>> [ 1.869159] mmcblk0: mmc0:0001 NCard 14.5 GiB
>>> [ 1.872639] mmcblk0boot0: mmc0:0001 NCard partition 1 4.00 MiB
>>> [ 1.878497] mmcblk0boot1: mmc0:0001 NCard partition 2 4.00 MiB
>>> [ 1.884356] mmcblk0rpmb: mmc0:0001 NCard partition 3 128 KiB <<<=====
>>> [ 2.000339] meson-gx-mmc d0070000.mmc: allocated mmc-pwrseq
>>> [ 2.044090] meson-gx-mmc d0072000.mmc: Got CD GPIO
>>> [ 2.062850] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
>>> [ 2.064869] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.070129] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.077161] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
>>> [ 2.120693] mmc2: Skipping voltage switch
>>> [ 2.148795] mmc1: new high speed SDIO card at address 0001
>>> [ 2.154443] mmc2: new high speed SDHC card at address 59b4
>>> [ 2.154660] mmcblk2: mmc2:59b4 USD00 29.5 GiB
>>> [ 2.159402] mmcblk2: p1 p2
>>> [ 6.550881] brcmfmac: brcmf_chip_recognition: SB chip is not supported <<<=====
>>> [ 6.556606] brcmfmac: brcmf_sdio_probe_attach: brcmf_chip_attach failed!
>>> [ 6.563260] brcmfmac: brcmf_sdio_probe: brcmf_sdio_probe_attach failed
>>> [ 6.569796] brcmfmac: brcmf_ops_sdio_probe: F2 error, probe failed -19...
>>>
>>> regards
>>> Helmut
>>>
>>
>> Thanks a lot for the additional information. The first version of the patch
>> set broke byte mode obviously (block mode is working fine).
>>
>> Before submitting a new version of the patch set:
>> Could you please apply patches 1, 2, and 4 of the patch set plus the
>> following one and re-test?
>>
>> Thanks, Heiner
>>
>> ---
>> drivers/mmc/host/meson-gx-mmc.c | 222 ++++++++++++++++++++++------------------
>> 1 file changed, 124 insertions(+), 98 deletions(-)
>>
>> diff --git a/drivers/mmc/host/meson-gx-mmc.c b/drivers/mmc/host/meson-gx-mmc.c
>> index 6bfd3da9..ca685902 100644
>> --- a/drivers/mmc/host/meson-gx-mmc.c
>> +++ b/drivers/mmc/host/meson-gx-mmc.c
>> @@ -121,6 +121,13 @@
>> #define SD_EMMC_CFG_CMD_GAP 16 /* in clock cycles */
>> #define MUX_CLK_NUM_PARENTS 2
>>
>> +struct sd_emmc_desc {
>> + u32 cmd_cfg;
>> + u32 cmd_arg;
>> + u32 cmd_data;
>> + u32 cmd_resp;
>> +};
>> +
>> struct meson_host {
>> struct device *dev;
>> struct mmc_host *mmc;
>> @@ -136,19 +143,12 @@ struct meson_host {
>> struct clk_divider cfg_div;
>> struct clk *cfg_div_clk;
>>
>> - unsigned int bounce_buf_size;
>> - void *bounce_buf;
>> - dma_addr_t bounce_dma_addr;
>> + struct sd_emmc_desc *descs;
>> + dma_addr_t descs_dma_addr;
>>
>> bool vqmmc_enabled;
>> };
>>
>> -struct sd_emmc_desc {
>> - u32 cmd_cfg;
>> - u32 cmd_arg;
>> - u32 cmd_data;
>> - u32 cmd_resp;
>> -};
>> #define CMD_CFG_LENGTH_SHIFT 0
>> #define CMD_CFG_LENGTH_MASK 0x1ff
>> #define CMD_CFG_BLOCK_MODE BIT(9)
>> @@ -185,6 +185,36 @@ static struct mmc_command *meson_mmc_get_next_command(struct mmc_command *cmd)
>> return NULL;
>> }
>>
>> +static enum dma_data_direction meson_mmc_get_data_dir(struct mmc_data *data)
>> +{
>> + return data->flags & MMC_DATA_WRITE ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
>> +}
>> +
>> +static void meson_mmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
>> +{
>> + struct mmc_data *data = mrq->data;
>> +
>> + if (!data)
>> + return;
>> +
>> + data->host_cookie = true;
>> +
>> + data->sg_count = dma_map_sg(mmc_dev(mmc), data->sg, data->sg_len,
>> + meson_mmc_get_data_dir(data));
>> + if (!data->sg_count)
>> + dev_err(mmc_dev(mmc), "dma_map_sg failed");
>> +}
>> +
>> +static void meson_mmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
>> + int err)
>> +{
>> + struct mmc_data *data = mrq->data;
>> +
>> + if (data && data->sg_count)
>> + dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len,
>> + meson_mmc_get_data_dir(data));
>> +}
>> +
>> static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate)
>> {
>> struct mmc_host *mmc = host->mmc;
>> @@ -434,104 +464,102 @@ static void meson_mmc_request_done(struct mmc_host *mmc,
>> static void meson_mmc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd)
>> {
>> struct meson_host *host = mmc_priv(mmc);
>> - struct sd_emmc_desc *desc, desc_tmp;
>> - u32 cfg;
>> - u8 blk_len, cmd_cfg_timeout;
>> - unsigned int xfer_bytes = 0;
>> + struct sd_emmc_desc *desc = host->descs;
>> + struct mmc_data *data = cmd->data;
>> + struct scatterlist *sg;
>> + u32 cfg, cmd_cfg = 0;
>> + u8 blk_len;
>> + int i;
>>
>> - /* Setup descriptors */
>> dma_rmb();
>> - desc = &desc_tmp;
>> - memset(desc, 0, sizeof(struct sd_emmc_desc));
>>
>> - desc->cmd_cfg |= (cmd->opcode & CMD_CFG_CMD_INDEX_MASK) <<
>> - CMD_CFG_CMD_INDEX_SHIFT;
>> - desc->cmd_cfg |= CMD_CFG_OWNER; /* owned by CPU */
>> - desc->cmd_arg = cmd->arg;
>> + cmd_cfg |= (cmd->opcode & CMD_CFG_CMD_INDEX_MASK) <<
>> + CMD_CFG_CMD_INDEX_SHIFT;
>> + cmd_cfg |= CMD_CFG_OWNER; /* owned by CPU */
>>
>> /* Response */
>> if (cmd->flags & MMC_RSP_PRESENT) {
>> - desc->cmd_cfg &= ~CMD_CFG_NO_RESP;
>> if (cmd->flags & MMC_RSP_136)
>> - desc->cmd_cfg |= CMD_CFG_RESP_128;
>> - desc->cmd_cfg |= CMD_CFG_RESP_NUM;
>> - desc->cmd_resp = 0;
>> + cmd_cfg |= CMD_CFG_RESP_128;
>> + cmd_cfg |= CMD_CFG_RESP_NUM;
>>
>> if (!(cmd->flags & MMC_RSP_CRC))
>> - desc->cmd_cfg |= CMD_CFG_RESP_NOCRC;
>> + cmd_cfg |= CMD_CFG_RESP_NOCRC;
>>
>> if (cmd->flags & MMC_RSP_BUSY)
>> - desc->cmd_cfg |= CMD_CFG_R1B;
>> + cmd_cfg |= CMD_CFG_R1B;
>> } else {
>> - desc->cmd_cfg |= CMD_CFG_NO_RESP;
>> + cmd_cfg |= CMD_CFG_NO_RESP;
>> }
>>
>> - /* data? */
>> - if (cmd->data) {
>> - desc->cmd_cfg |= CMD_CFG_DATA_IO;
>> - if (cmd->data->blocks > 1) {
>> - desc->cmd_cfg |= CMD_CFG_BLOCK_MODE;
>> - desc->cmd_cfg |=
>> - (cmd->data->blocks & CMD_CFG_LENGTH_MASK) <<
>> - CMD_CFG_LENGTH_SHIFT;
>> + if (data) {
>> + cmd_cfg |= CMD_CFG_DATA_IO;
>> +
>> + if (data->blocks > 1) {
>> + cmd_cfg |= CMD_CFG_BLOCK_MODE;
>>
>> /* check if block-size matches, if not update */
>> cfg = readl(host->regs + SD_EMMC_CFG);
>> blk_len = cfg & (CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT);
>> blk_len >>= CFG_BLK_LEN_SHIFT;
>> - if (blk_len != ilog2(cmd->data->blksz)) {
>> - dev_dbg(host->dev, "%s: update blk_len %d -> %d\n",
>> - __func__, blk_len,
>> - ilog2(cmd->data->blksz));
>> - blk_len = ilog2(cmd->data->blksz);
>> + if (blk_len != ilog2(data->blksz)) {
>> + dev_dbg(host->dev,
>> + "%s: update blk_len %d -> %d\n",
>> + __func__, blk_len, ilog2(data->blksz));
>> + blk_len = ilog2(data->blksz);
>> cfg &= ~(CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT);
>> cfg |= blk_len << CFG_BLK_LEN_SHIFT;
>> writel(cfg, host->regs + SD_EMMC_CFG);
>> }
>> - } else {
>> - desc->cmd_cfg &= ~CMD_CFG_BLOCK_MODE;
>> - desc->cmd_cfg |=
>> - (cmd->data->blksz & CMD_CFG_LENGTH_MASK) <<
>> - CMD_CFG_LENGTH_SHIFT;
>> }
>>
>> - cmd->data->bytes_xfered = 0;
>> - xfer_bytes = cmd->data->blksz * cmd->data->blocks;
>> - if (cmd->data->flags & MMC_DATA_WRITE) {
>> - desc->cmd_cfg |= CMD_CFG_DATA_WR;
>> - WARN_ON(xfer_bytes > host->bounce_buf_size);
>> - sg_copy_to_buffer(cmd->data->sg, cmd->data->sg_len,
>> - host->bounce_buf, xfer_bytes);
>> - cmd->data->bytes_xfered = xfer_bytes;
>> - dma_wmb();
>> - } else {
>> - desc->cmd_cfg &= ~CMD_CFG_DATA_WR;
>> - }
>> + data->bytes_xfered = 0;
>> + if (data->flags & MMC_DATA_WRITE)
>> + cmd_cfg |= CMD_CFG_DATA_WR;
>>
>> - desc->cmd_data = host->bounce_dma_addr & CMD_DATA_MASK;
>> + cmd_cfg |= ilog2(SD_EMMC_CMD_TIMEOUT_DATA) <<
>> + CMD_CFG_TIMEOUT_SHIFT;
>> +
>> + for_each_sg(data->sg, sg, data->sg_count, i) {
>> + unsigned int len = sg_dma_len(sg);
>> +
>> + if (data->blocks > 1)
>> + len /= data->blksz;
>> +
>> + desc[i].cmd_cfg = cmd_cfg;
>> + desc[i].cmd_cfg |= (len & CMD_CFG_LENGTH_MASK) <<
>> + CMD_CFG_LENGTH_SHIFT;
>> + if (i > 0)
>> + desc[i].cmd_cfg |= CMD_CFG_NO_CMD;
>> + desc[i].cmd_arg = cmd->arg;
>> + desc[i].cmd_resp = 0;
>> + desc[i].cmd_data = sg_dma_address(sg);
>> + }
>> + desc[data->sg_count - 1].cmd_cfg |= CMD_CFG_END_OF_CHAIN;
>>
>> - cmd_cfg_timeout = ilog2(SD_EMMC_CMD_TIMEOUT_DATA);
>> } else {
>> - desc->cmd_cfg &= ~CMD_CFG_DATA_IO;
>> - cmd_cfg_timeout = ilog2(SD_EMMC_CMD_TIMEOUT);
>> + cmd_cfg |= ilog2(SD_EMMC_CMD_TIMEOUT) << CMD_CFG_TIMEOUT_SHIFT;
>> + cmd_cfg |= CMD_CFG_END_OF_CHAIN;
>> + desc[0].cmd_cfg = cmd_cfg;
>> + desc[0].cmd_arg = cmd->arg;
>> + desc[0].cmd_resp = 0;
>> + desc[0].cmd_data = 0;
>> }
>> - desc->cmd_cfg |= (cmd_cfg_timeout & CMD_CFG_TIMEOUT_MASK) <<
>> - CMD_CFG_TIMEOUT_SHIFT;
>>
>> host->cmd = cmd;
>>
>> - /* Last descriptor */
>> - desc->cmd_cfg |= CMD_CFG_END_OF_CHAIN;
>> - writel(desc->cmd_cfg, host->regs + SD_EMMC_CMD_CFG);
>> - writel(desc->cmd_data, host->regs + SD_EMMC_CMD_DAT);
>> - writel(desc->cmd_resp, host->regs + SD_EMMC_CMD_RSP);
>> wmb(); /* ensure descriptor is written before kicked */
>> - writel(desc->cmd_arg, host->regs + SD_EMMC_CMD_ARG);
>> + cfg = host->descs_dma_addr | START_DESC_BUSY;
>> + writel(cfg, host->regs + SD_EMMC_START);
>> }
>>
>> static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
>> {
>> struct meson_host *host = mmc_priv(mmc);
>> + bool needs_pre_post_req = mrq->data && !mrq->data->host_cookie;
>> +
>> + if (needs_pre_post_req)
>> + meson_mmc_pre_req(mmc, mrq);
>>
>> /* Stop execution */
>> writel(0, host->regs + SD_EMMC_START);
>> @@ -540,6 +568,9 @@ static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
>> meson_mmc_start_cmd(mmc, mrq->sbc);
>> else
>> meson_mmc_start_cmd(mmc, mrq->cmd);
>> +
>> + if (needs_pre_post_req)
>> + meson_mmc_post_req(mmc, mrq, 0);
>> }
>>
>> static void meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd)
>> @@ -560,6 +591,7 @@ static irqreturn_t meson_mmc_irq(int irq, void *dev_id)
>> {
>> struct meson_host *host = dev_id;
>> struct mmc_command *cmd;
>> + struct mmc_data *data;
>> u32 irq_en, status, raw_status;
>> irqreturn_t ret = IRQ_HANDLED;
>>
>> @@ -571,6 +603,8 @@ static irqreturn_t meson_mmc_irq(int irq, void *dev_id)
>> if (WARN_ON(!cmd))
>> return IRQ_NONE;
>>
>> + data = cmd->data;
>> +
>> spin_lock(&host->lock);
>> irq_en = readl(host->regs + SD_EMMC_IRQ_EN);
>> raw_status = readl(host->regs + SD_EMMC_STATUS);
>> @@ -608,12 +642,17 @@ static irqreturn_t meson_mmc_irq(int irq, void *dev_id)
>> dev_dbg(host->dev, "Unhandled IRQ: Descriptor timeout\n");
>> cmd->error = -ETIMEDOUT;
>> }
>> +
>> + if (data && !cmd->error)
>> + data->bytes_xfered = data->blksz * data->blocks;
>> +
>> if (status & IRQ_SDIO)
>> dev_dbg(host->dev, "Unhandled IRQ: SDIO.\n");
>>
>> - if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS))
>> - ret = IRQ_WAKE_THREAD;
>> - else {
>> + if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) {
>> + if (meson_mmc_get_next_command(cmd))
>> + ret = IRQ_WAKE_THREAD;
>> + } else {
>> dev_warn(host->dev, "Unknown IRQ! status=0x%04x: MMC CMD%u arg=0x%08x flags=0x%08x stop=%d\n",
>> status, cmd->opcode, cmd->arg,
>> cmd->flags, cmd->mrq->stop ? 1 : 0);
>> @@ -642,26 +681,12 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
>> {
>> struct meson_host *host = dev_id;
>> struct mmc_command *next_cmd, *cmd = host->cmd;
>> - struct mmc_data *data;
>> - unsigned int xfer_bytes;
>>
>> if (WARN_ON(!cmd))
>> return IRQ_NONE;
>>
>> - data = cmd->data;
>> - if (data && data->flags & MMC_DATA_READ) {
>> - xfer_bytes = data->blksz * data->blocks;
>> - WARN_ON(xfer_bytes > host->bounce_buf_size);
>> - sg_copy_from_buffer(data->sg, data->sg_len,
>> - host->bounce_buf, xfer_bytes);
>> - data->bytes_xfered = xfer_bytes;
>> - }
>> -
>> next_cmd = meson_mmc_get_next_command(cmd);
>> - if (next_cmd)
>> - meson_mmc_start_cmd(host->mmc, next_cmd);
>> - else
>> - meson_mmc_request_done(host->mmc, cmd->mrq);
>> + meson_mmc_start_cmd(host->mmc, next_cmd);
>>
>> return IRQ_HANDLED;
>> }
>> @@ -695,6 +720,8 @@ static const struct mmc_host_ops meson_mmc_ops = {
>> .request = meson_mmc_request,
>> .set_ios = meson_mmc_set_ios,
>> .get_cd = meson_mmc_get_cd,
>> + .pre_req = meson_mmc_pre_req,
>> + .post_req = meson_mmc_post_req,
>> };
>>
>> static int meson_mmc_probe(struct platform_device *pdev)
>> @@ -774,15 +801,14 @@ static int meson_mmc_probe(struct platform_device *pdev)
>>
>> mmc->caps |= MMC_CAP_CMD23;
>> mmc->max_blk_count = CMD_CFG_LENGTH_MASK;
>> - mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
>> -
>> - /* data bounce buffer */
>> - host->bounce_buf_size = mmc->max_req_size;
>> - host->bounce_buf =
>> - dma_alloc_coherent(host->dev, host->bounce_buf_size,
>> - &host->bounce_dma_addr, GFP_KERNEL);
>> - if (host->bounce_buf == NULL) {
>> - dev_err(host->dev, "Unable to map allocate DMA bounce buffer.\n");
>> + mmc->max_segs = PAGE_SIZE / sizeof(struct sd_emmc_desc);
>> + mmc->max_seg_size = mmc->max_blk_count * mmc->max_blk_size;
>> + mmc->max_req_size = mmc->max_seg_size * mmc->max_segs;
>> +
>> + host->descs = dma_alloc_coherent(host->dev, PAGE_SIZE,
>> + &host->descs_dma_addr, GFP_KERNEL);
>> + if (!host->descs) {
>> + dev_err(host->dev, "Allocating descriptor DMA buffer failed\n");
>> ret = -ENOMEM;
>> goto err_div_clk;
>> }
>> @@ -807,8 +833,8 @@ static int meson_mmc_remove(struct platform_device *pdev)
>> /* disable interrupts */
>> writel(0, host->regs + SD_EMMC_IRQ_EN);
>>
>> - dma_free_coherent(host->dev, host->bounce_buf_size,
>> - host->bounce_buf, host->bounce_dma_addr);
>> + dma_free_coherent(host->dev, PAGE_SIZE, host->descs,
>> + host->descs_dma_addr);
>>
>> clk_disable_unprepare(host->cfg_div_clk);
>> clk_disable_unprepare(host->core_clk);
>>
>
> compared to the patches 1...5 there is absolutely no change to patches 1, 2, 4 and the above. Neither syslog nor performance.
>
Thanks for re-testing. I have a little bit of a hard time to understand why SD and eMMC mode
are working but SDIO (at least with brcfmac) is not. Especially as I don't have HW to test SDIO mode on.
After patches 1, 2, 4 the system is still working normally?
And would it be possible for you to compile a DEBUG kernel and post the mmc/brcmfmac related output?
In DEBUG mode mode brcmfmac driver logs all SDIO transfers.
Last but not least, could you please post /proc/interrupts ? This would give an idea whether any SDIO
or just specific ones fail.
Thanks, Heiner
> regards
> Helmut
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
