Hi Ulf,
On 24/01/17 08:16, Ulf Hansson wrote:
> On 16 January 2017 at 17:56, Maxime Ripard
> <maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
>> Experience have shown that the using the autocalibration could severely
>> degrade the performances of the MMC bus.
>>
>> Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
>> Remove the calibration code for now, and add comments to document our
>> findings.
>
> So doesn't this break some platforms using HS400? Or are you saying
> those are already broken?
This is a sunxi specific calibration routine, which was introduced
lately (e1b8dfd1b1c6) to be used by the Allwinner's enhanced MMC
controller. This is only used by devices using the sun50i-a64-mmc
compatible, of which this series introduces the first user.
So there is no way this can regress in any way, since the code wasn't
actually used before.
Cheers,
Andre.
>
>>
>> Reviewed-by: Andre Przywara <andre.przywara@xxxxxxx>
>> Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
>> ---
>> drivers/mmc/host/sunxi-mmc.c | 50 ++++++++++++-------------------------
>> 1 file changed, 17 insertions(+), 33 deletions(-)
>>
>> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
>> index 019f95e8e7c5..b9c8a62bc212 100644
>> --- a/drivers/mmc/host/sunxi-mmc.c
>> +++ b/drivers/mmc/host/sunxi-mmc.c
>> @@ -683,41 +683,19 @@ static int sunxi_mmc_oclk_onoff(struct sunxi_mmc_host *host, u32 oclk_en)
>>
>> static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off)
>> {
>> - u32 reg = readl(host->reg_base + reg_off);
>> - u32 delay;
>> - unsigned long timeout;
>> -
>> if (!host->cfg->can_calibrate)
>> return 0;
>>
>> - reg &= ~(SDXC_CAL_DL_MASK << SDXC_CAL_DL_SW_SHIFT);
>> - reg &= ~SDXC_CAL_DL_SW_EN;
>> -
>> - writel(reg | SDXC_CAL_START, host->reg_base + reg_off);
>> -
>> - dev_dbg(mmc_dev(host->mmc), "calibration started\n");
>> -
>> - timeout = jiffies + HZ * SDXC_CAL_TIMEOUT;
>> -
>> - while (!((reg = readl(host->reg_base + reg_off)) & SDXC_CAL_DONE)) {
>> - if (time_before(jiffies, timeout))
>> - cpu_relax();
>> - else {
>> - reg &= ~SDXC_CAL_START;
>> - writel(reg, host->reg_base + reg_off);
>> -
>> - return -ETIMEDOUT;
>> - }
>> - }
>> -
>> - delay = (reg >> SDXC_CAL_DL_SHIFT) & SDXC_CAL_DL_MASK;
>> -
>> - reg &= ~SDXC_CAL_START;
>> - reg |= (delay << SDXC_CAL_DL_SW_SHIFT) | SDXC_CAL_DL_SW_EN;
>> -
>> - writel(reg, host->reg_base + reg_off);
>> -
>> - dev_dbg(mmc_dev(host->mmc), "calibration ended, reg is 0x%x\n", reg);
>> + /*
>> + * FIXME:
>> + * This is not clear how the calibration is supposed to work
>> + * yet. The best rate have been obtained by simply setting the
>> + * delay to 0, as Allwinner does in its BSP.
>> + *
>> + * The only mode that doesn't have such a delay is HS400, that
>> + * is in itself a TODO.
>> + */
>> + writel(SDXC_CAL_DL_SW_EN, host->reg_base + reg_off);
>>
>> return 0;
>> }
>> @@ -809,7 +787,13 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,
>> if (ret)
>> return ret;
>>
>> - /* TODO: enable calibrate on sdc2 SDXC_REG_DS_DL_REG of A64 */
>> + /*
>> + * FIXME:
>> + *
>> + * In HS400 we'll also need to calibrate the data strobe
>> + * signal. This should only happen on the MMC2 controller (at
>> + * least on the A64).
>> + */
>>
>> return sunxi_mmc_oclk_onoff(host, 1);
>> }
>> --
>> git-series 0.8.11
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
