Re: [PATCH 3/5] arm64: dts: sun50i: add MMC nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 03/01/17 02:52, Chen-Yu Tsai wrote:

Hi,

> On Tue, Jan 3, 2017 at 7:03 AM, Andre Przywara <andre.przywara@xxxxxxx> wrote:
> 
> A commit message explaining the mmc controllers would be nice.

OK.

>> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
>> ---
>>  arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 67 +++++++++++++++++++++++++++
>>  1 file changed, 67 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> index e0dcab8..c680566 100644
>> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> @@ -150,6 +150,32 @@
>>                                 pins = "PB8", "PB9";
>>                                 function = "uart0";
>>                         };
>> +
>> +                       mmc0_pins: mmc0@0 {
>> +                               pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
>> +                               function = "mmc0";
>> +                               drive-strength = <30>;
>> +                       };
>> +
>> +                       mmc0_default_cd_pin: mmc0_cd_pin@0 {
>> +                               pins = "PF6";
>> +                               function = "gpio_in";
>> +                               bias-pull-up;
>> +                       };
> 
> We are starting to drop pinmux nodes for gpio usage.

And replacing them with what?
Or do you mean they go in the individual board .dts files?
In this case I believe having a default pin defined here would help to
define it in every .dts.

>> +
>> +                       mmc1_pins: mmc1@0 {
>> +                               pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
>> +                               function = "mmc1";
>> +                               drive-strength = <30>;
>> +                       };
>> +
>> +                       mmc2_pins: mmc2@0 {
>> +                               pins = "PC1", "PC5", "PC6", "PC8", "PC9",
>> +                                      "PC10", "PC11", "PC12", "PC13", "PC14",
>> +                                      "PC15", "PC16";
>> +                               function = "mmc2";
>> +                               drive-strength = <30>;
>> +                       };
> 
> Moreover I think you should split out the pinmux nodes to a separate patch.

I can surely do, just wondering what's the rationale is behind that?

> 
>>                 };
>>
>>                 uart0: serial@1c28000 {
>> @@ -240,6 +266,47 @@
>>                         #size-cells = <0>;
>>                 };
>>
>> +               mmc0: mmc@1c0f000 {
>> +                       compatible = "allwinner,sun50i-a64-mmc",
>> +                                    "allwinner,sun5i-a13-mmc";
> 
> Given that sun5i doesn't support mmc delay timings, and the A64 has
> calibration and delay timings, I wouldn't call them compatible.
> 
> Or are you claiming that for the A64 has a delay of 0 for the
> currently supported speeds, so the calibration doesn't really
> matter? If so this should be mentioned in the commit message.

Yes, that's my observation: Driving it with sun5-a13-mmc just works.
This sun5i driver version does not (and will never) support higher
transfer modes anyway, so for that subset they are compatible. This
opens up the door to other operating systems not having a particular
driver for the A64, for instance, also older Linux kernels.
I know that sunxi doesn't use this compatible feature much, but IMHO we
should really start thinking about the DT not just being Linux specific
- or even being specific to a certain Linux version. And this case here
is a good example: An A13 MMC driver can drive this device - if there is
no better driver (an A64 one) available.

> 
>> +                       reg = <0x01c0f000 0x1000>;
>> +                       clocks = <&ccu 31>, <&ccu 75>;
> 
> The clock / reset index macros are in the tree now.
> Please switch to them.

The include file is in the tree, but it isn't used in the current HEAD
(as in #included and the actual macros being used in the .dtsi).
So I was wondering if there is a patch pending for that?

Cheers,
Andre

>> +                       clock-names = "ahb", "mmc";
>> +                       resets = <&ccu 8>;
>> +                       reset-names = "ahb";
>> +                       interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
>> +                       status = "disabled";
>> +                       #address-cells = <1>;
>> +                       #size-cells = <0>;
>> +               };
>> +
>> +               mmc1: mmc@1c10000 {
>> +                       compatible = "allwinner,sun50i-a64-mmc",
>> +                                    "allwinner,sun5i-a13-mmc";
>> +                       reg = <0x01c10000 0x1000>;
>> +                       clocks = <&ccu 32>, <&ccu 76>;
>> +                       clock-names = "ahb", "mmc";
>> +                       resets = <&ccu 9>;
>> +                       reset-names = "ahb";
>> +                       interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
>> +                       status = "disabled";
>> +                       #address-cells = <1>;
>> +                       #size-cells = <0>;
>> +               };
>> +
>> +               mmc2: mmc@1c11000 {
>> +                       compatible = "allwinner,sun50i-a64-emmc";
>> +                       reg = <0x01c11000 0x1000>;
>> +                       clocks = <&ccu 33>, <&ccu 77>;
>> +                       clock-names = "ahb", "mmc";
>> +                       resets = <&ccu 10>;
>> +                       reset-names = "ahb";
>> +                       interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> +                       status = "disabled";
>> +                       #address-cells = <1>;
>> +                       #size-cells = <0>;
>> +               };
>> +
>>                 gic: interrupt-controller@1c81000 {
>>                         compatible = "arm,gic-400";
>>                         reg = <0x01c81000 0x1000>,
>> --
>> 2.8.2
>>

--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux