Hi Marek,
> Marek Vasut <marex@xxxxxxx> hat am 6. August 2016 um 15:13 geschrieben:
>
>
> On 08/06/2016 02:55 PM, Stefan Wahren wrote:
> > This patch implements driver support for 3.3V DDR eMMCs.
> >
> > Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
> > ---
> > drivers/mmc/host/mxs-mmc.c | 22 ++++++++++++++++++++++
> > 1 file changed, 22 insertions(+)
> >
> > diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
> > index d839147..84019d5 100644
> > --- a/drivers/mmc/host/mxs-mmc.c
> > +++ b/drivers/mmc/host/mxs-mmc.c
> > @@ -71,6 +71,7 @@ struct mxs_mmc_host {
> > spinlock_t lock;
> > int sdio_irq_en;
> > bool broken_cd;
> > + bool is_ddr;
> > };
> >
> > static int mxs_mmc_get_cd(struct mmc_host *mmc)
> > @@ -411,6 +412,9 @@ static void mxs_mmc_adtc(struct mxs_mmc_host *host)
> > cmd0 |= BF_SSP(log2_blksz, CMD0_BLOCK_SIZE) |
> > BF_SSP(blocks - 1, CMD0_BLOCK_COUNT);
> > } else {
> > + if (host->is_ddr)
> > + cmd0 |= BM_SSP_CMD0_DBL_DATA_RATE_EN;
> > +
> > writel(data_size, ssp->base + HW_SSP_XFER_SIZE);
> > writel(BF_SSP(log2_blksz, BLOCK_SIZE_BLOCK_SIZE) |
> > BF_SSP(blocks - 1, BLOCK_SIZE_BLOCK_COUNT),
> > @@ -499,6 +503,7 @@ static void mxs_mmc_request(struct mmc_host *mmc, struct
> > mmc_request *mrq)
> > static void mxs_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> > {
> > struct mxs_mmc_host *host = mmc_priv(mmc);
> > + struct mxs_ssp *ssp = &host->ssp;
> >
> > if (ios->bus_width == MMC_BUS_WIDTH_8)
> > host->bus_width = 2;
> > @@ -509,6 +514,23 @@ static void mxs_mmc_set_ios(struct mmc_host *mmc,
> > struct mmc_ios *ios)
> >
> > if (ios->clock)
> > mxs_ssp_set_clk_rate(&host->ssp, ios->clock);
> > +
> > + if (ssp_is_old(ssp))
> > + return;
> > +
> > + if (ios->timing == MMC_TIMING_MMC_DDR52) {
>
> Shouldn't you validate that the clock are set to at least 52MHz before
> neabling the DDR mode ?
according to the i.MX28 datasheet IMX28CEC
3.5.14.2 MMC4.4 (Dual Data Rate) AC Timing
the minimum clock frequency is 0 and maximum is 52 MHz. So i assume the core
take care of the right clock rate.
>
> > + /*
> > + * ENGR00133481-1: In DDR mode the host send the data at
> > + * negative edge and the MMC receive the data at positive edge.
> > + */
> > + host->is_ddr = true;
> > + writel(BM_SSP_CTRL1_POLARITY, ssp->base +
> > + HW_SSP_CTRL1(ssp) + STMP_OFFSET_REG_CLR);
> > + } else {
>
> Is it by any chance possible that this else branch will catch not only
> the non-DDR options, but also some DDR ones , thus causing problems ?
No, because the polarity bit has been set all the time by mxs_mmc_reset().
But it's possible that i didn't catch all DDR cases.
>
> > + host->is_ddr = false;
> > + writel(BM_SSP_CTRL1_POLARITY, ssp->base + HW_SSP_CTRL1(ssp) +
> > + STMP_OFFSET_REG_SET);
> > + }
> > }
> >
> > static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
> >
>
>
> --
> Best regards,
> Marek Vasut
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
