On Wed, Aug 03, 2016 at 04:18:42PM -0700, Kevin Hilman wrote:
> Add binding and basic support for the SD/eMMC controller on Amlogic
> S905/GXBB devices.
>
> Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 29 +++++++++
> .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 74 ++++++++++++++++++++++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 71 +++++++++++++++++++++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 36 ++++++++++-
> 4 files changed, 209 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
> new file mode 100644
> index 000000000000..2bfdf47018c5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
> @@ -0,0 +1,29 @@
> +Amlogic SD / eMMC controller for S905/GXBB family SoCs
> +
> +The MMC 5.1 compliant host controller on Amlogic provides the
> +interface for SD, eMMC and SDIO devices.
> +
> +This file documents the properties in addition to those available in
> +the MMC core bindings, documented by mmc.txt.
> +
> +Required properties:
> +- compatible : contains "amlogic,meson-gxbb"
> +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
> +- clock-names: Should contain the following:
> + "core" - Main peripheral bus clock
> + "clkin0" - Parent clock of internal mux
> + "clkin1" - Other parent clock of internal mux
> + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the
> + clock rate requested by the MMC core.
> +
> +Example:
> +
> + sd_emmc_a: mmc@70000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x70000 0x0 0x2000>;
> + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + pinctrl-0 = <&emmc_pins>;
> + };
> +
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 90a84c514d3d..f41d8fe5c706 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -73,6 +73,45 @@
> default-state = "off";
> };
> };
> +
> + mmc_iv: gpio-regulator {
> + compatible = "regulator-gpio";
> +
> + regulator-name = "mmc-gpio-supply";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
> + gpio-states = <0 1>;
> +
> + /*
> + * Based on ODROID-C2 schematics:
> + * signal name: IO_TF_3V3N_1V8, GPIOAO bit 3
> + */
> + states = <3300000 0
> + 1800000 1>;
There are multiple things wrong in this node based on the regulator-gpio
documentation.
> + };
> +
> + vcc1v8: regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc3v3: regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> };
>
> &uart_AO {
> @@ -87,3 +126,38 @@
> pinctrl-names = "default";
> };
>
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + vmmc-supply = <&mmc_iv>;
> + voltage-ranges = <1800 3300>;
> +};
> +
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <8>;
> + cap-sd-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + voltage-ranges = <1800 3300>;
> + vmmc-supply = <&vcc3v3>;
> + vmmcq-sumpply = <&vcc1v8>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> index f4f30f674b4c..77698815943a 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -57,6 +57,42 @@
> device_type = "memory";
> reg = <0x0 0x0 0x0 0x40000000>;
> };
> +
> + mmc_iv: gpio-regulator {
> + compatible = "regulator-gpio";
> +
> + regulator-name = "mmc-gpio-supply";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
> + gpio-states = <0 1>;
> +
> + /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
> + states = <1800000 0
> + 3300000 1>;
> + };
> +
> + vddio_boot: regulator {
[...]
> + vcc_3v3: regulator {
This won't even compile as you have the same node name twice.
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> };
>
> /* This UART is brought out to the DB9 connector */
> @@ -72,3 +108,38 @@
> pinctrl-names = "default";
> };
>
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + voltage-ranges = <1800 3300>;
> + vmmc-supply = <&mmc_iv>;
> +};
> +
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <8>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + voltage-ranges = <1800 3300>;
> + vmmc-supply = <&vcc_3v3>;
> + vmmcq-sumpply = <&vddio_boot>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> index 35c8b2beb05c..2c200f96467c 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -247,7 +247,8 @@
> mux {
> groups = "emmc_nand_d07",
> "emmc_cmd",
> - "emmc_clk";
> + "emmc_clk",
> + "emmc_ds";
> function = "emmc";
> };
> };
> @@ -330,6 +331,39 @@
> #address-cells = <2>;
> #size-cells = <2>;
> ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
> +
> + sd_emmc_a: mmc@70000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x70000 0x0 0x2000>;
> + interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_A>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> + sd_emmc_b: mmc@72000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x72000 0x0 0x2000>;
> + interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_B>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> + sd_emmc_c: mmc@74000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x74000 0x0 0x2000>;
> + interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_C>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> };
>
> ethmac: ethernet@c9410000 {
> --
> 2.9.0
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
