On 2016/7/19 16:13, Jaehoon Chung wrote: > Hi, > > Removed the unnecessary CC'd. > > On 07/19/2016 04:51 PM, Jin Guojun wrote: >> From: j00226943 <j00226943@xxxxxxxxxxxxxxxxxxxx> > > What is j00226943? > > When you send the patch for dw_mmc controller, plz use the prefix "mmc: dw_mmc: ". > >> >> Two more changes: >> >> Before we send cmd,we need to set CMD bit29 to >> 1 so that CMD and DATA sent to card through the HOLD Register, >> This is the explication in synosys host:To meet the relatively >> high Input Hold Time requirement for SDR12, SDR25, and other MMC >> speed modes, you should program bit[29]use_hold_Reg of the CMD >> register to 1'b1; the output data is then registered again in the >> cclk_in_drv domain by using the Hold Register as shown in Path B >> of Figure 10-8. However, for the higher speed modes of SDR104, SDR50 >> and DDR50, you can meet the much smaller Input Hold Time requirement >> of 0.8ns by bypassing the Hold Register (Path A in Figure 10-8, >> programming CMD.use_hold_reg = 1'b0) and then adding delay elements >> on the output path as indicated >> >> We have no tuning function in our drivers,so we must do the >> Function piling when we init UHS card. 1.For hikey we cant support UHS for SD card in https://github.com/96boards-hikey/linux/tree/hikey-mainline-rebase 2.I have no SDMMC_CMD_USE_HOLD_REG in Dw_mmc-k3.c > > Sorry..this patch is NACK. > SDMMC_CMD_USE_HOLD_REG is already used by default in dw_mmc.c > Which kernel version did you use? > >> >> Signed-off-by: Jin Guojun <kid.jin@xxxxxxxxxxxxx> >> --- >> drivers/mmc/host/dw_mmc-k3.c | 6 ++++++ >> drivers/mmc/host/dw_mmc.c | 2 ++ >> 2 files changed, 8 insertions(+) >> >> diff --git a/drivers/mmc/host/dw_mmc-k3.c b/drivers/mmc/host/dw_mmc-k3.c >> index 63c2e2e..2cbfcc7 100644 >> --- a/drivers/mmc/host/dw_mmc-k3.c >> +++ b/drivers/mmc/host/dw_mmc-k3.c >> @@ -125,10 +125,16 @@ static void dw_mci_hi6220_set_ios(struct dw_mci *host, struct mmc_ios *ios) >> host->bus_hz = clk_get_rate(host->biu_clk); >> } >> >> +static void dw_mci_hi6220_prepare_command(struct dw_mci *host, u32 *cmdr) >> +{ >> + *cmdr |= SDMMC_CMD_USE_HOLD_REG; >> +} >> + >> static const struct dw_mci_drv_data hi6220_data = { >> .switch_voltage = dw_mci_hi6220_switch_voltage, >> .set_ios = dw_mci_hi6220_set_ios, >> .parse_dt = dw_mci_hi6220_parse_dt, >> + .prepare_command = dw_mci_hi6220_prepare_command, >> }; Hi,thank you for your review 1.We do the prepare_command in dw_mci_prepare_command before we send CMD in dw_mmc.c 2.I can find the same drivers in dw_mmc-exynos.c 3.For hikey we do the initialization from Dw_mmc-k3.c,so I need to do the prepare_command in hi6220 drivers > > There is no "prepare_command" hooks. > > Best Regards, > Jaehoon Chung > >> >> static const struct of_device_id dw_mci_k3_match[] = { >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c >> index 9dd1bd3..047e116 100644 >> --- a/drivers/mmc/host/dw_mmc.c >> +++ b/drivers/mmc/host/dw_mmc.c >> @@ -1564,6 +1564,8 @@ static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode) >> >> if (drv_data && drv_data->execute_tuning) >> err = drv_data->execute_tuning(slot, opcode); >> + else >> + err = 0; >> return err; >> } >> >> > > > . > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
