Hi,
My third approach for a USB power sequence which fixes usb3503+lan
on Odroid U3 board if it was initialized by bootloader
(e.g. for TFTP boot).
Changes since v2
================
1. Add Javier's reviewed-by tags. Address some comments.
2. Re-use existing properties for GPIOs etc by pwrseq-simple
driver. New property is still added: "power-sequence".
I tried to address and do according to Rob's comments.
Please look at patch 6/12 ("power: pwrseq: simple: Add support
for regulator and generic property") for bindings and the
new code around matching "power-sequence" property.
3. I marked the usb code as "EXAMPLE" because that part
is left to Peter Chen.
Problem
=======
When Odroid U3 (usb3503 + smsc95xx + max77686) boots from network (TFTP),
the usb3503 and LAN smsc95xx do not show up in "lsusb". Hard-reset
is required, e.g. by suspend to RAM. The actual TFTP boot does
not have to happen. Just "usb start" from U-Boot is sufficient.
>From the schematics, the regulator is a supply only to LAN, however
without toggling it off/on, the usb3503 hub won appear neither.
Solution
========
This is very similar to the MMC pwrseq behavior so the idea is to:
1. Move MMC pwrseq drivers to generic place,
2. Extend the pwrseq-simple with regulator toggling,
3. Add support to USB hub and port core for pwrseq,
4. Toggle the regulator when needed.
Best regards,
Krzysztof
Krzysztof Kozlowski (12):
power/mmc: Move pwrseq drivers to power/pwrseq
MAINTAINERS: Retain Ulf Hansson as the same maintainer of pwrseq
power: pwrseq: Enable COMPILE_TEST for drivers
power: pwrseq: Remove mmc prefix from mmc_pwrseq
power: pwrseq: Generalize mmc_pwrseq operations by removing mmc prefix
power: pwrseq: simple: Add support for regulator and generic property
power: pwrseq: Add support for USB hubs with external power
usb: hub: Handle deferred probe
EXAMPLE CODE: usb: port: Parse pwrseq phandle from Device Tree
EXAMPLE CODE: usb: hub: Power sequence the ports on activation
ARM: dts: exynos: Switch the buck8 to GPIO mode on Odroid U3
ARM: dts: exynos: Fix LAN and HUB after bootloader initialization on
Odroid U3
.../pwrseq/pwrseq-emmc.txt} | 0
.../pwrseq/pwrseq-simple.txt} | 29 +++-
MAINTAINERS | 9 ++
arch/arm/boot/dts/exynos4412-odroidu3.dts | 5 +
drivers/mmc/Kconfig | 2 -
drivers/mmc/core/Makefile | 3 -
drivers/mmc/core/core.c | 8 +-
drivers/mmc/core/host.c | 2 +-
drivers/mmc/core/pwrseq.c | 110 ---------------
drivers/mmc/core/pwrseq.h | 52 -------
drivers/power/Kconfig | 1 +
drivers/power/Makefile | 1 +
drivers/{mmc/core => power/pwrseq}/Kconfig | 22 ++-
drivers/power/pwrseq/Makefile | 3 +
drivers/power/pwrseq/pwrseq.c | 153 +++++++++++++++++++++
drivers/{mmc/core => power/pwrseq}/pwrseq_emmc.c | 17 +--
drivers/{mmc/core => power/pwrseq}/pwrseq_simple.c | 110 ++++++++++++---
drivers/usb/core/hub.c | 16 ++-
drivers/usb/core/hub.h | 3 +
drivers/usb/core/port.c | 15 ++
include/linux/mmc/host.h | 4 +-
include/linux/pwrseq.h | 63 +++++++++
22 files changed, 414 insertions(+), 214 deletions(-)
rename Documentation/devicetree/bindings/{mmc/mmc-pwrseq-emmc.txt => power/pwrseq/pwrseq-emmc.txt} (100%)
rename Documentation/devicetree/bindings/{mmc/mmc-pwrseq-simple.txt => power/pwrseq/pwrseq-simple.txt} (53%)
delete mode 100644 drivers/mmc/core/pwrseq.c
delete mode 100644 drivers/mmc/core/pwrseq.h
rename drivers/{mmc/core => power/pwrseq}/Kconfig (60%)
create mode 100644 drivers/power/pwrseq/Makefile
create mode 100644 drivers/power/pwrseq/pwrseq.c
rename drivers/{mmc/core => power/pwrseq}/pwrseq_emmc.c (88%)
rename drivers/{mmc/core => power/pwrseq}/pwrseq_simple.c (52%)
create mode 100644 include/linux/pwrseq.h
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
