On 13/05/16 15:19, Ludovic Desroches wrote:
> On Fri, May 13, 2016 at 02:37:21PM +0300, Adrian Hunter wrote:
>> + cc some Marvell people because they added this code
>>
>> On 13/05/16 12:27, Ludovic Desroches wrote:
>>> Activating wakeup event is not enough to get a wakeup signal. The
>>> corresponding events have to be enabled in the Interrupt Status Enable
>>> Register too.
>>
>> That seems to follow the specification. Did you find that you actually
>> needed this change to get it to work?
>>
>
> Yes, I din't wake up on card event without this patch.
>
>>>
>>> Signed-off-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
>>> ---
>>> Hi,
>>>
>>> I just updated sdhci_enable_irq_wakeups() not sdhci_disable_irq_wakeups()
>>> because I don't think it is necessary to configure SDHCI_INT_ENABLE at this
>>> step, it will be done with sdhci_init() or sdhci_enable_card_detection().
>>
>> OK, but that should be in the commit message and commented in the code too.
>
> I'll add it.
>
>>
>>>
>>> While I was writing this patch, several questions came to my mind:
>>> - Is the naming correct? wakeup signal is not an irq. 'enable_irq_wakeups' can
>>> be a bit confusing.
>>
>> I don't support renaming things unless the names are really really bad.
>> These names are OK.
>>
>>> - If we want to wakeup from irq, we may have to set SDHCI_INT_ENABLE and
>>> SDHCI_SIGNAL_ENABLE and not rely on a previous configuration, isn't it?
>>
>> I imagine the card interrupt will occur when it is enabled. I don't know
>> about card insert / remove.
>>
>> What works for you?
>>
>
> I only use wakeup events and not irqs in system PM (patches for
> sdhci-of-at91 are not sent yet, I am waiting for the inclusion of other
> patches).
It doesn't hurt to say in the commit message what driver or hardware needed
the change.
>
> What I mean is that if we want to wake up from irqs, it could be safer and
> clearer to set explicitely SDHCI_INT_ENABLE and SDHCI_SIGNAL_ENABLE in
> sdhci_enable_irq_wakeups(). It is just a thought and not needed for this
> patch.
>
>>>
>>> Regards
>>>
>>> Ludovic
>>>
>>> drivers/mmc/host/sdhci.c | 26 ++++++++++++++++++--------
>>> 1 file changed, 18 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>>> index b284924..6fc69ed 100644
>>> --- a/drivers/mmc/host/sdhci.c
>>> +++ b/drivers/mmc/host/sdhci.c
>>> @@ -2638,18 +2638,28 @@ static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
>>> \*****************************************************************************/
>>>
>>> #ifdef CONFIG_PM
>>> +/*
>>> + * To enable wakeup events, the corresponding events have to be enabled in
>>> + * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
>>> + * Table' in the SD Host Controller Standard Specification.
>>> + */
>>> void sdhci_enable_irq_wakeups(struct sdhci_host *host)
>>> {
>>> - u8 val;
>>> - u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
>>> - | SDHCI_WAKE_ON_INT;
>>> + u8 wakeup_val;
>>> + u8 wakeup_mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
>>> + SDHCI_WAKE_ON_INT;
>>
>> Please don't rename variables, or tidy-up code that you are not changing.
>>
>
> I thought it will be better to have wakeup_val and irq_val instead of
> val and irq_val. That's why I renamed it while introducing irq_val.
val and irq_val are fine.
>
>>> + u32 irq_val = SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
>>> + SDHCI_INT_CARD_INT;
>>>
>>> - val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
>>> - val |= mask ;
>>
>> These 2 line are actually unchanged.
>>
>>> + wakeup_val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
>>> + wakeup_val |= wakeup_mask;
>>> /* Avoid fake wake up */
>>> - if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
>>> - val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
>>> - sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
>>> + if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) {
>>> + wakeup_val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
>>> + irq_val &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
>>> + }
>>> + sdhci_writeb(host, wakeup_val, SDHCI_WAKE_UP_CONTROL);
>>> + sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
>>> }
>>> EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
>>>
>>>
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
