On 04/05/16 09:54, Chaotian Jing wrote:
> Per JEDEC spec, it is not recommended to use CMD13 to get card status
> after speed mode switch. below are two reason about this:
> 1. CMD13 cannot be guaranteed due to the asynchronous operation.
> Therefore it is not recommended to use CMD13 to check busy completion
> of the timing change indication.
> 2. After switch to HS200, CMD13 will get response of 0x800, and even the
> busy signal gets de-asserted, the response of CMD13 is aslo 0x800.
>
> this patch drops CMD13 when doing speed mode switch, if host do not
> support MMC_CAP_WAIT_WHILE_BUSY and there is no ops->card_busy(),
> then the only way is to wait a fixed timeout.
This looks like it should be 3 patches:
1. Change __mmc_switch
2. Change HS200 and HS400 selection
3. Change HS selection
However there is another problem: card_busy is not the same as busy signal -
see below. So that needs to be sorted out first.
>
> Signed-off-by: Chaotian Jing <chaotian.jing@xxxxxxxxxxxx>
> ---
> drivers/mmc/core/mmc.c | 82 ++++++++++++++++----------------------------
> drivers/mmc/core/mmc_ops.c | 25 +++++++++-----
> 2 files changed, 45 insertions(+), 62 deletions(-)
>
> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> index 4dbe3df..03ee7a4 100644
> --- a/drivers/mmc/core/mmc.c
> +++ b/drivers/mmc/core/mmc.c
> @@ -962,7 +962,7 @@ static int mmc_select_hs(struct mmc_card *card)
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS,
> card->ext_csd.generic_cmd6_time,
> - true, true, true);
> + true, false, true);
If you are going to do that, then you still need to do mmc_switch_status(card).
But we have done CMD13 polling for HS for a long time, so this should be a
separate patch and separately justified. Maybe we should still poll if
!(host->caps & MMC_CAP_WAIT_WHILE_BUSY) && !host->ops->card_busy.
> if (!err)
> mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
>
> @@ -1056,7 +1056,6 @@ static int mmc_switch_status(struct mmc_card *card)
> static int mmc_select_hs400(struct mmc_card *card)
> {
> struct mmc_host *host = card->host;
> - bool send_status = true;
> unsigned int max_dtr;
> int err = 0;
> u8 val;
> @@ -1068,9 +1067,6 @@ static int mmc_select_hs400(struct mmc_card *card)
> host->ios.bus_width == MMC_BUS_WIDTH_8))
> return 0;
>
> - if (host->caps & MMC_CAP_WAIT_WHILE_BUSY)
> - send_status = false;
> -
> /* Reduce frequency to HS frequency */
> max_dtr = card->ext_csd.hs_max_dtr;
> mmc_set_clock(host, max_dtr);
> @@ -1080,7 +1076,7 @@ static int mmc_select_hs400(struct mmc_card *card)
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> EXT_CSD_HS_TIMING, val,
> card->ext_csd.generic_cmd6_time,
> - true, send_status, true);
> + true, false, true);
> if (err) {
> pr_err("%s: switch to high-speed from hs200 failed, err:%d\n",
> mmc_hostname(host), err);
> @@ -1090,11 +1086,9 @@ static int mmc_select_hs400(struct mmc_card *card)
> /* Set host controller to HS timing */
> mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
>
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - if (err)
> - goto out_err;
> - }
> + err = mmc_switch_status(card);
> + if (err)
> + goto out_err;
>
> /* Switch card to DDR */
> err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> @@ -1113,7 +1107,7 @@ static int mmc_select_hs400(struct mmc_card *card)
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> EXT_CSD_HS_TIMING, val,
> card->ext_csd.generic_cmd6_time,
> - true, send_status, true);
> + true, false, true);
> if (err) {
> pr_err("%s: switch to hs400 failed, err:%d\n",
> mmc_hostname(host), err);
> @@ -1124,11 +1118,9 @@ static int mmc_select_hs400(struct mmc_card *card)
> mmc_set_timing(host, MMC_TIMING_MMC_HS400);
> mmc_set_bus_speed(card);
>
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - if (err)
> - goto out_err;
> - }
> + err = mmc_switch_status(card);
> + if (err)
> + goto out_err;
>
> return 0;
>
> @@ -1146,14 +1138,10 @@ int mmc_hs200_to_hs400(struct mmc_card *card)
> int mmc_hs400_to_hs200(struct mmc_card *card)
> {
> struct mmc_host *host = card->host;
> - bool send_status = true;
> unsigned int max_dtr;
> int err;
> u8 val;
>
> - if (host->caps & MMC_CAP_WAIT_WHILE_BUSY)
> - send_status = false;
> -
> /* Reduce frequency to HS */
> max_dtr = card->ext_csd.hs_max_dtr;
> mmc_set_clock(host, max_dtr);
> @@ -1162,49 +1150,43 @@ int mmc_hs400_to_hs200(struct mmc_card *card)
> val = EXT_CSD_TIMING_HS;
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
> val, card->ext_csd.generic_cmd6_time,
> - true, send_status, true);
> + true, false, true);
> if (err)
> goto out_err;
>
> mmc_set_timing(host, MMC_TIMING_MMC_DDR52);
>
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - if (err)
> - goto out_err;
> - }
> + err = mmc_switch_status(card);
> + if (err)
> + goto out_err;
>
> /* Switch HS DDR to HS */
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_BUS_WIDTH,
> EXT_CSD_BUS_WIDTH_8, card->ext_csd.generic_cmd6_time,
> - true, send_status, true);
> + true, false, true);
> if (err)
> goto out_err;
>
> mmc_set_timing(host, MMC_TIMING_MMC_HS);
>
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - if (err)
> - goto out_err;
> - }
> + err = mmc_switch_status(card);
> + if (err)
> + goto out_err;
>
> /* Switch HS to HS200 */
> val = EXT_CSD_TIMING_HS200 |
> card->drive_strength << EXT_CSD_DRV_STR_SHIFT;
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
> val, card->ext_csd.generic_cmd6_time, true,
> - send_status, true);
> + false, true);
> if (err)
> goto out_err;
>
> mmc_set_timing(host, MMC_TIMING_MMC_HS200);
>
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - if (err)
> - goto out_err;
> - }
> + err = mmc_switch_status(card);
> + if (err)
> + goto out_err;
>
> mmc_set_bus_speed(card);
>
> @@ -1243,7 +1225,6 @@ static void mmc_select_driver_type(struct mmc_card *card)
> static int mmc_select_hs200(struct mmc_card *card)
> {
> struct mmc_host *host = card->host;
> - bool send_status = true;
> unsigned int old_timing;
> int err = -EINVAL;
> u8 val;
> @@ -1260,9 +1241,6 @@ static int mmc_select_hs200(struct mmc_card *card)
>
> mmc_select_driver_type(card);
>
> - if (host->caps & MMC_CAP_WAIT_WHILE_BUSY)
> - send_status = false;
> -
> /*
> * Set the bus width(4 or 8) with host's support and
> * switch to HS200 mode if bus width is set successfully.
> @@ -1274,20 +1252,18 @@ static int mmc_select_hs200(struct mmc_card *card)
> err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> EXT_CSD_HS_TIMING, val,
> card->ext_csd.generic_cmd6_time,
> - true, send_status, true);
> + true, false, true);
> if (err)
> goto err;
> old_timing = host->ios.timing;
> mmc_set_timing(host, MMC_TIMING_MMC_HS200);
> - if (!send_status) {
> - err = mmc_switch_status(card);
> - /*
> - * mmc_select_timing() assumes timing has not changed if
> - * it is a switch error.
> - */
> - if (err == -EBADMSG)
> - mmc_set_timing(host, old_timing);
> - }
> + err = mmc_switch_status(card);
> + /*
> + * mmc_select_timing() assumes timing has not changed if
> + * it is a switch error.
> + */
> + if (err == -EBADMSG)
> + mmc_set_timing(host, old_timing);
> }
> err:
> if (err)
> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> index 62355bd..32de144 100644
> --- a/drivers/mmc/core/mmc_ops.c
> +++ b/drivers/mmc/core/mmc_ops.c
> @@ -480,6 +480,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
> u32 status = 0;
> bool use_r1b_resp = use_busy_signal;
> bool expired = false;
> + bool busy = false;
>
> mmc_retune_hold(host);
>
> @@ -535,19 +536,24 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
> /* Must check status to be sure of no errors. */
> timeout = jiffies + msecs_to_jiffies(timeout_ms);
> do {
> + /*
> + * Due to the possibility of being preempted after
> + * sending the status command, check the expiration
> + * time first.
> + */
> + expired = time_after(jiffies, timeout);
> if (send_status) {
> - /*
> - * Due to the possibility of being preempted after
> - * sending the status command, check the expiration
> - * time first.
> - */
> - expired = time_after(jiffies, timeout);
> err = __mmc_send_status(card, &status, ignore_crc);
> if (err)
> goto out;
> }
> if ((host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp)
> break;
> + if (host->ops->card_busy) {
card_busy is a problem because it is designed for SD voltage switch which
checks DAT[3:0] whereas the busy signal is only DAT0.
> + if (!host->ops->card_busy(host))
> + break;
> + busy = true;
> + }
> if (mmc_host_is_spi(host))
> break;
I would tend to put all the changes together here after the
mmc_host_is_spi() check i.e.
if (host->ops->card_busy) {
expired = time_after(jiffies, timeout);
if (!host->ops->card_busy(host))
break;
if (!expired) {
cond_resched();
continue;
}
pr_err("%s: Card stuck in busy state! %s\n",
mmc_hostname(host), __func__);
err = -ETIMEDOUT;
goto out;
}
Also I think the changes to __mmc_switch() should be a separate patch.
However you can't go forward with this until you sort out what card_busy means.
>
> @@ -556,19 +562,20 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
> * does'nt support MMC_CAP_WAIT_WHILE_BUSY, then we can only
> * rely on waiting for the stated timeout to be sufficient.
> */
> - if (!send_status) {
> + if (!send_status && !host->ops->card_busy) {
> mmc_delay(timeout_ms);
> goto out;
> }
>
> /* Timeout if the device never leaves the program state. */
> - if (expired && R1_CURRENT_STATE(status) == R1_STATE_PRG) {
> + if (expired &&
> + (R1_CURRENT_STATE(status) == R1_STATE_PRG || busy)) {
> pr_err("%s: Card stuck in programming state! %s\n",
> mmc_hostname(host), __func__);
> err = -ETIMEDOUT;
> goto out;
> }
> - } while (R1_CURRENT_STATE(status) == R1_STATE_PRG);
> + } while (R1_CURRENT_STATE(status) == R1_STATE_PRG || busy);
>
> err = mmc_switch_status_error(host, status);
> out:
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
