On 23 April 2016 at 10:37, Franz <flash86@xxxxxx> wrote: > I am trying to get an SD Card to work via SPI interface. I am using a > RaspberryPI Compute Module with kernel Version 4.4, but I can't get it > to work properly. I've tried it with the native spi interface as well as > with the spi aux interface and also with a gpio bitbang spi interface. > It's always the same error: > > [ 2639.558282] mmc1: new SD card on SPI > [ 2639.566325] mmcblk1: mmc1:0000 SD256 243 MiB > [ 2639.646120] mmcblk1: p1 < > > [ 2639.833759] mmcblk1: error -38 sending status command, retrying > [ 2639.839973] mmcblk1: error -38 sending status command, retrying > [ 2639.846170] mmcblk1: error -38 sending status command, aborting > [ 2639.853406] mmc1: SPI card removed > [ 2640.240223] mmc1: host does not support reading read-only switch, > assuming write-enable > [ 2640.248328] mmc1: new SD card on SPI > [ 2640.256373] mmcblk1: mmc1:0000 SD256 243 MiB > [ 2640.336068] mmcblk1: p1 < > > [ 2640.523545] mmcblk1: error -38 sending status command, retrying > [ 2640.529757] mmcblk1: error -38 sending status command, retrying > [ 2640.535893] mmcblk1: error -38 sending status command, aborting > [ 2640.543129] mmc1: SPI card removed > [ 2640.930176] mmc1: host does not support reading read-only switch, > assuming write-enable > [ 2640.938313] mmc1: new SD card on SPI > [ 2640.946679] mmcblk1: mmc1:0000 SD256 243 MiB > [ 2641.026395] mmcblk1: p1 < > > [ 2641.213996] mmcblk1: error -38 sending status command, retrying > [ 2641.220208] mmcblk1: error -38 sending status command, retrying > [ 2641.226344] mmcblk1: error -38 sending status command, aborting > [ 2641.233435] mmc1: SPI card removed > [ 2641.620177] mmc1: host does not support reading read-only switch, > assuming write-enable > [ 2641.628277] mmc1: new SD card on SPI > [ 2641.636530] mmcblk1: mmc1:0000 SD256 243 MiB > [ 2641.716114] mmcblk1: p1 < > > [ 2641.903636] mmcblk1: error -38 sending status command, retrying > [ 2641.909852] mmcblk1: error -38 sending status command, retrying > [ 2641.915987] mmcblk1: error -38 sending status command, aborting > [ 2641.923056] mmc1: SPI card removed > > I don't have any RO or CD pins configured, just plain SPI interface > directly to the SD Card. I've tried it with different SD cards with > differen capacities. It's always the same error. The above messages > appear in a endless loop.The last time I've used the mmc_spi driver was > kernel 3.8 I think with this version everything worked without any > problems. Does anyone know how to fix this? So it seems to be a regression. I would try a bisect and see if it can pin-point us to a certain commit that causes the issue. Kind regards Uffe -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
