Hello Krzysztof,
On 04/27/2016 10:00 AM, Krzysztof Kozlowski wrote:
> The eMMC card vmmc-supply contained incorrectly two regulators: LDO20
> and buck8. The second one is ignored. Additionally the buck8 is a vqmmc
> supply only on X and X2. On U3 the buck8 is providing power to the LAN
> (SMSC95xx) so instead the LDO22 should be used.
>
> Fix this by defining proper vmmc and vqmmc supplies for respective
> boards.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>
> ---
>
> Changes since v1:
> 1. buck8 is used on X/X2 so differentiate the configuration (hint by
> Tobias Jakobi).
> ---
> arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 13 ++++++++++---
> arch/arm/boot/dts/exynos4412-odroidu3.dts | 18 ++++++++++++++++++
> arch/arm/boot/dts/exynos4412-odroidx.dts | 11 +++++++++++
> arch/arm/boot/dts/exynos4412-odroidx2.dts | 11 +++++++++++
> 4 files changed, 50 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> index 3d0d44581fbd..34a5b3daced0 100644
> --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> @@ -347,6 +347,13 @@
> regulator-boot-on;
> };
>
> + ldo22_reg: LDO22 {
> + regulator-name = "LDO22";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3950000>;
> + regulator-boot-on;
> + };
> +
I don't have a datasheet for the max77686 but I guess these min and max
values are the actual voltage range that the ldo22 regulator can support?
If that's the case, then I don't think setting these are correct since the
DT binding says that the regulator-{min,max}-microvolt properties describe
the voltage range that consumers may set. I've seen Mark mention this many
times, the last one I remember is at [0].
Probably would be better to leave the ldo22_reg definition to odroidu3.dts
to avoid setting these constraint in a .dtsi file.
> ldo25_reg: LDO25 {
> regulator-name = "VDDQ_LCD_1.8V";
> regulator-min-microvolt = <1800000>;
> @@ -411,8 +418,8 @@
>
> buck8_reg: BUCK8 {
> regulator-name = "BUCK8_2.8V";
> - regulator-min-microvolt = <2800000>;
> - regulator-max-microvolt = <2800000>;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <3900000>;
Same here, since not all boards have the same constraint for this regulator,
it would be better to remove it from the .dtsi and let each dts to define it.
> };
> };
> };
> @@ -456,7 +463,7 @@
> &mshc_0 {
> pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
> pinctrl-names = "default";
> - vmmc-supply = <&ldo20_reg &buck8_reg>;
> + vmmc-supply = <&ldo20_reg>;
> mmc-pwrseq = <&emmc_pwrseq>;
> status = "okay";
>
> diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts
> index dd89f7b37c9f..d73aa6c58fe3 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts
> @@ -69,6 +69,24 @@
> };
> };
>
> +/* Supply for LAN9730/SMSC95xx */
> +&buck8_reg {
> + regulator-name = "BUCK8_P3V3";
I think it would be better to name it "BUCK8_3.3V" for consistency.
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +};
> +
> +/* VDDQ for MSHC (eMMC card) */
> +&ldo22_reg {
> + regulator-name = "LDO22_VDDQ_MMC4_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +};
> +
> +&mshc_0 {
> + vqmmc-supply = <&ldo22_reg>;
> +};
> +
> &pwm {
> pinctrl-0 = <&pwm0_out>;
> pinctrl-names = "default";
> diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
> index bf7b21b817e4..2af235151301 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidx.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
> @@ -63,12 +63,23 @@
> };
> };
>
> +/* VDDQ for MSHC (eMMC card) */
> +&buck8_reg {
> + regulator-name = "BUCK8_VDDQ_MMC4_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +};
> +
> &ehci {
> port@1 {
> status = "okay";
> };
> };
>
> +&mshc_0 {
> + vqmmc-supply = <&buck8_reg>;
> +};
> +
> &pinctrl_1 {
> gpio_home_key: home_key {
> samsung,pins = "gpx2-2";
> diff --git a/arch/arm/boot/dts/exynos4412-odroidx2.dts b/arch/arm/boot/dts/exynos4412-odroidx2.dts
> index 6e33678562ae..3e3584270e00 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidx2.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidx2.dts
> @@ -22,6 +22,17 @@
> };
> };
>
> +/* VDDQ for MSHC (eMMC card) */
> +&buck8_reg {
> + regulator-name = "BUCK8_VDDQ_MMC4_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +};
> +
> +&mshc_0 {
> + vqmmc-supply = <&buck8_reg>;
> +};
> +
> &sound {
> simple-audio-card,name = "Odroid-X2";
> simple-audio-card,widgets =
>
Rest looks good, so if you do those changes feel free to add:
Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
[0]: http://www.spinics.net/lists/linux-omap/msg127035.html
Best regards,
--
Javier Martinez Canillas
Open Source Group
Samsung Research America
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
