Re: [PATCH] mmc: sdhci-tegra: Set DMA mask

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 02/26/2016 08:31 PM, Arnd Bergmann wrote:
On Friday 26 February 2016 16:24:34 Alexandre Courbot wrote:
On Thu, Feb 25, 2016 at 11:52 PM, Arnd Bergmann <arnd@xxxxxxxx> wrote:
Actually even if we specify a dma-ranges on the parent DT node, the
DMA range will still be limited to 32 bits because of the following
code in of_dma_configure():

     /*
      * Set default coherent_dma_mask to 32 bit.  Drivers are expected to
      * setup the correct supported mask.
      */
     if (!dev->coherent_dma_mask)
         dev->coherent_dma_mask = DMA_BIT_MASK(32);

     /*
      * Set it to coherent_dma_mask by default if the architecture
      * code has not set it.
      */
     if (!dev->dma_mask)
         dev->dma_mask = &dev->coherent_dma_mask;

     ....
     /* gets dma-ranges into dma_addr and size */
     ....


     *dev->dma_mask = min((*dev->dma_mask),
                  DMA_BIT_MASK(ilog2(dma_addr + size)));

So unless the DMA mask is set on the device before of_dma_configure()
is called, the min() statement will choose the 32 bits mask that has
been previously set. So IIUC in any case, the driver will need to call
dma_set_mask()

Yes, the driver definitely has to call dma_set_mask(), the property of
the parent bus is used to make that fail when the bus doesn't support
it.

And that's where things seem to stop working: the driver's probe
function is invoked by the platform bus, *after* of_dma_configure() is
called. So unless I am missing something there is no way for the
driver to set the DMA mask in such a way that of_dma_configure() can
see it and do the right thing.

In other words, most of the DMA mask logic in of_dma_configure()
doesn't seem to have any effect (and a 32 bits mask will be set), at
least on the platform bus.

That is correct: of_dma_configure has to set a 32-bit DMA mask
because that is the default that we expect to see in Linux drivers.

A lot of drivers don't call dma_set_mask() at all, so this is
the most reasonable value that typically works, unless the
device is more limited, or you want the extra performance you
get on devices that actually support a bigger mask.

Can I have your thoughts on this? Am I missing something?

One point: I think the dma_set_mask() probably should be in the
generic part of the sdhci driver, not the tegra specific portion.

Ok, but then how does the generic part of the driver knows which DMA
mask applies to the device?

If dma_set_mask() succeeds when passed a 64-bit mask, the driver
can pass high addresses into dma_map_*() and put the result into
the 64-bit DMA registers of the device. That is all the driver
needs to know here.

When the bus is more limited than the device, we either have
an swiotlb/iommu that will use bounce buffers to map dma_map_* work
anyway (using low DMA addresses for high memory), or we don't have
an swiotlb and the dma_set_mask() operation has to fail.

Ok, I think I understand. I was expecting of_dma_configure() to do more than it actually needs to and be the final arbiter of a device's DMA mask. That's obviously not the case - thanks for the thorough explanation.

Let me send a v2 of this to see if I got it properly.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux