On 20/01/2016 02:17, Shawn Lin wrote:
> On 2016/1/19 23:33, Mason wrote:
>
>> My SoC provides an Arasan SDIO/eMMC controller supported by the
>> drivers/mmc/host/sdhci-of-arasan.c driver.
>>
>> At init, the driver prints a warning to the console:
>>
>> [ 0.887301] sdhci: Secure Digital Host Controller Interface driver
>> [ 0.893537] sdhci: Copyright(c) Pierre Ossman
>> [ 0.897928] sdhci-pltfm: SDHCI platform and OF driver helper
>> [ 0.903903] sdhci-arasan 21000.mmc: No vmmc regulator found
>> [ 0.909537] sdhci-arasan 21000.mmc: No vqmmc regulator found
>> [ 0.915247] mmc0: Invalid maximum block size, assuming 512 bytes
>> [ 0.953797] mmc0: SDHCI controller on 21000.mmc [21000.mmc] using ADMA
>> [ 0.961494] sdhci-arasan 21200.mmc: No vmmc regulator found
>> [ 0.967110] sdhci-arasan 21200.mmc: No vqmmc regulator found
>>
>> Is "mmc0: Invalid maximum block size, assuming 512 bytes" something
>> serious which requires investigating, in your experience?
>
> you can look into this commit 0633f654241
> From <SD host controller simplified specfication version 3.00>
> sdhci doesn't support blocks of 4096 bytes.
>
> But at least check my arasan-5.1 databook, it supports 4096 from
> the capabilities register. So, you don't force arasan to use
> SDHCI_QUIRK_FORCE_BLK_SZ_2048, then sdhci core force it to be 512 bytes.
> Not serious problem, just a proper warn.
>
>> The corresponding DT is:
>>
>> mmc0: mmc@21000 {
>> compatible = "arasan,sdhci-8.9a";
>> reg = <0x21000 0x200>;
>> clock-names = "clk_xin", "clk_ahb";
>> clocks = <&sdio_clk>, <&clkgen 1>;
>> interrupts = <60 IRQ_TYPE_LEVEL_HIGH>;
>> };
Hello Shawn,
Thanks for pointing out SDHCI_QUIRK_FORCE_BLK_SZ_2048.
I don't think there is currently a way to enable this quirk
for the Arasan controller from the device tree, right?
$ git grep SDHCI_QUIRK_FORCE_BLK_SZ_2048 drivers/mmc
drivers/mmc/host/sdhci-bcm-kona.c: SDHCI_QUIRK_FORCE_BLK_SZ_2048 |
drivers/mmc/host/sdhci-esdhc.h:#define ESDHC_DEFAULT_QUIRKS (SDHCI_QUIRK_FORCE_BLK_SZ_2048 | \
drivers/mmc/host/sdhci.c: if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
drivers/mmc/host/sdhci.h:#define SDHCI_QUIRK_FORCE_BLK_SZ_2048 (1<<20)
So that means I have to write code in
drivers/mmc/host/sdhci-of-arasan.c correct?
Regards.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
